Business Routers Forums - Business Community

Exclude one WAN port from load balancing

Hi, I'm having ER605 v1 managed by Omada SDN Software Controller 5.6.3. In my setup I have 3 WAN networks as follows: The first 2 WANs which are connected to WAN & WAN/LAN 1 port of the network are di

Load Balancing

By Charitha · Latest post 2022-10-31 04:13:54 by Charitha

2Helpful

183Views

3Replies

TP Link ER 605 with Omada controller version 5.5.6 disconnects Wan every other day at the same time

Hello. Strange behaivior since updating my ER-605 to 1.2.1 and my Omada controller(running on a raspberry pi with mbentley/omada-controller 5.5.6) https://hub.docker.com/r/mbentley/omada-controller My

Firmware UpdateLoad BalancingDHCP Service

By jonas740 · Latest post 2022-09-30 05:56:25 by dsj

0Helpful

285Views

3Replies

Port Forwarding in ER605 from Cosmote Booster & Cosmote Oxygen (for Unraid server)

I did this settings to enable access to my Unraid from External places through the Unraid - MyServers and seems to be working fine The internal settings in ER605 are set to automatic-LoadBalance The t

VLAN & Multi-NetworksLoad BalancingPort ForwardingDualWan

By Apostolos55

4Helpful

117Views

0Replies

Want to route server on a sub-LAN to a particular WAN

I have two WANs. On the LAN side I have the ER605 serving IP addresses (192.168.0.xx) to a number of devices. One of these is a Mesh network, which has its own router and subnet (192.168.5.xx). I have

VLAN & Multi-NetworksLoad BalancingDHCP Service

By rtX · Latest post 2022-09-24 21:51:22 by btx

0Helpful

607Views

11Replies

How to guarantee bandwidth

Hello, On our older router (TL-ER6020) I could guarantee bandwidth for our voip phones, but this ER7206 only has a cap option rather than a guaranteed option under the Bandwidth Control section of the

Load Balancing

By JasonPamir · Latest post 2022-09-19 07:42:46 by Somnus

0Helpful

105Views

1Replies

ER605 for dual WAN load balance and failover?

Hi. I have a 250 Mb connection and a 45 Mb connection. Will ER605 be able to successfully provide load balance and failover (incase one WAN fails) without any throttling? I am using Mikrotik rb750gr3

Load BalancingVLAN & Multi-Networks

By kashif789us · Latest post 2022-09-11 00:42:46 by kashif789us

2Helpful

1243Views

6Replies

Detected Large ping attack. Dropped x packets

Hello I have 3 internet line the router is TL-ER5120 in system log i see a lot of this message Detected Large ping attack. Dropped x packets. and the internet is very slow in Traffic Statistics i see

Load Balancing

By Aabed · Latest post 2022-09-08 08:39:25 by Virgo

2Helpful

774Views

2Replies

Virtual-Server and One-to-one NAT failures and hairpin/loopback issues

I have experimented quite a bit with both features. I have 13 static IPs from my ISP. They work just fine outside ER7206 (WAN) side. I started with firmware 1.2.1 Reading through all the firmware patc

Firmware UpdateLoad BalancingPort ForwardingVLAN & Multi-Networks

By smallscript

1Helpful

214Views

0Replies

Best load balancing mode for double WAN 4G + VDSL

Hi all, I would like to ask for the recommended configuration of load balancing for the following situation: I have a cable internet connection with 1Mbps Upload that works fine for navigation and low

Load Balancing

By leki389 · Latest post 2022-09-01 05:56:20 by Somnus

0Helpful

146Views

1Replies

TL-ER7206 - two WAN with same subnet (and even IP address)

Hi. A quick technical question - will two (or more) WAN connections on same logical subnet work in load-balancing mode? For example - WAN1 has 192.168.10.10/24 and WAN2 has the same? And i can't confi

VLAN & Multi-NetworksLoad Balancing

By n0p · Latest post 2022-08-19 21:19:38 by MaximusMark

0Helpful

474Views

2Replies