No internet access when connected to OpenVPN
Hi all,
I have a Client-to-Site VPN with OpenVPN running on my TL-R605. This works perfectly fine on my iPhone, however I can only connect to local devices. Access to the internet is not working and that is annoying since I have to disconnect from the VPN to access internet resources.
I read the documentation but nothing is mentioned regarding additional configuration to access the internet.
How I configured the VPN:
Joeri
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I have been able to test this week, strangely I had internet access this time around. One thing I couldn't see is to send all traffic through the vpn instead of local traffic, is it possible to edit the server config file to include redirect-gateway?
- Copy Link
- Report Inappropriate Content
I connected to the OpenVPN server with my laptop.
Execute "route print" command and you will find the route tables.
I found that two routes were added, one is 0.0.0.0 mask 0.0.0.0 go via OpenVPN Interface;
the second is 192.168.10.0 mask 255.255.255.0 go via OpenVPN Interface;
But 0.0.0.0 mask 0.0.0.0 go via my ethernet adapter has a higher priority, so all the Internet requests are going from the Internet rather than the VPN.
- Copy Link
- Report Inappropriate Content
Dear @Filip.Bak,
Hi All, I have and Archer MR200 and have a similar problem. Im running OpenVPN on this router with this configuration :
The Archer MR200 is a 4G WiFi Router, you may start a thread in the Home Network Community > 3G/4G Routers/MiFi. Thank you!
- Copy Link
- Report Inappropriate Content
@Fae it was brought to my attention by an TP-representative from the Netherlands, this problem might be solved in Omada 4.3. together with firmware upgrades for the omada hardware.
When will this version be available to the public?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I have the same problem with openvpn.
I can connect to the lan but I cannot browse internet.
I have a TL-R605 in SDN configuration with 2 lans
192.168.0.1/24
192.168.1.1/24
The openvpn is configured this way
I also updated the firmware and the omada software that run on a windows pc in the first lan
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
With openvpn gui I can browse internet but using my local dns, so the traffic is not encrypted (?)
Is it possible to use the remote network?
- Copy Link
- Report Inappropriate Content
Hi Gyus,
I have configure openvpn server and clients has 192.168.80.0/24
I think problem is with DNS resolving,
I can ping 8.8.8.8
C:\Users\peter>ping 8.8.8.8
Pinging 8.8.8.8 with 32 bytes of data:
Reply from 8.8.8.8: bytes=32 time=10ms TTL=118
Reply from 8.8.8.8: bytes=32 time=10ms TTL=118
but I can not ping www.sme.sk because following:
Users\peter>nslookup wwww.sme.sk
DNS request timed out.
timeout was 2 seconds.
Server: UnKnown
Address: 192.168.80.1
DNS request timed out.
timeout was 2 seconds.
DNS request timed out.
timeout was 2 seconds.
DNS request timed out.
timeout was 2 seconds.
DNS request timed out.
timeout was 2 seconds.
*** Request to UnKnown timed-out
my ipconfig :
IPv4 Address. . . . . . . . . . . : 192.168.80.6(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.252
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 318832596
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-26-68-C7-1F-5C-80-B6-F8-1E-2F
DNS Servers . . . . . . . . . . . : 192.168.80.1
8.8.8.8
my question is why TPLINK configure DNS like this?
why there is no possibilty to configure dns by myself?
And why default second DNS is 8.8.8.8?
ANY answer from TPLINK?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 25130
Replies: 70
Voters 0
No one has voted for it yet.