TP-Link Community

Unable to obtain anything other than a /64 IPv6 prefix

I'm only able to get a /64 IPv6 prefix from my ISP. They suggested trying: Sending a prefix hint with a requested prefix - omada controller does not support this, standalone gateway does not support t

IPv6

By DcnPat · Latest post an hour ago

0Helpful

6Views

0Replies

TL-SG1016DE 7.6 wrong firmware installed and on website?

Hello I just (Dec 27 2025) purchased this switch on Amazon. The label clearly states it is hardware version 7.6 but the firmware loaded in it is designated as version 7.0. The download page from TP-Li

ConfigurationFirmware Update

By Clarocque · Latest post an hour ago by D-C

0Helpful

14Views

1Replies

Why do Agile series switches need to be "activated" separately in the site list?

Hello, i use an OC200 (Omada v6.0.0.36) and have now integrated an ES205GP (Firmware v1_1.0.3 Build 20250609). That i can integrate Switches from the Agile Series, i must activate this in the Site-Lis

ConfigurationControllerSwitch

By lukass2000 · Latest post 12 hours ago by MR.S

0Helpful

21Views

1Replies

Firmware to Support for Australian WiFi frequencies

It is awesome to see actual Australian firmware in the new EAP603 Outdoor! EAP603-Outdoor(AU) v1.0 This means the EAP supports the correct WiFi frequencies and transmission strengths for Australia. Co

Firmware UpdateAustralia

By whereisaaron · Latest post 19 hours ago

0Helpful

26Views

0Replies

Mongobleed

Dear Team, Does the security issue reported for Mongo CVE-2025-14847 also apply for the software-based Omada controller? One recommendation offered to remedy - in case no immediate update to a patched

Controller

By Eg64 · Latest post 16 hours ago by Eg64

0Helpful

42Views

2Replies

Can the SG2428LP supply access points with 24 volts via PoE?

Hello, I bought an SG2428LP, which provides PoE. This supports PoE 802.3at/af. In my Omada System there are two EAP225 and one EAP 115 Outdoor integrated. All access points use 24 volts PoE power. Can

By lukass2000 · Latest post 12 hours ago by D-C

0Helpful

42Views

3Replies

Increase limit of MAC groups

Hello, I've Omada software controller (v6.1.0.11), ER8411 v1.0 (1.3.6), SG2210XMP-M2 v1.0 (1.0.18), SX3008F v1.20 (1.20.14) and EAP650(EU) v1.0 (1.1.3). It's very struggling that with this setup I can

By Werpet · Latest post 6 hours ago by Werpet

1Helpful

35Views

3Replies

Couldn't connect to internet

Hello guys.. I have two CPE510 devices.. I set up one as AP and the other as Client. My problem is, in the client side when I connect my laptop to the LAN port in the injector there is internet connec

Pharos ControlOutdoor Wi-Fi Solution

By Seraj2211 · Latest post Yesterday

0Helpful

27Views

0Replies

Is it possible to see which device was logged into an access point and when?

Hello, When I select an access point in the OC220, the information window opens on the right. In this window, I can see which devices are currently connected to the access point. Is there a way to see

ControllerLogs

By lukass2000 · Latest post 17 hours ago by lukass2000

0Helpful

74Views

4Replies

OC 300

I'm trying to access the OC300 controller to reduce the shadow area between the 20 access points spread throughout the company. This is because when I activate fast roaming via the mobile app, the car

By NiltonFelipe · Latest post Yesterday

0Helpful

33Views

0Replies