Deco

TP-Link Deco is a whole-home Wi-Fi mesh solution providing seamless Wi-Fi coverage for your house. In this section you can say hello to other members, ask, answer or discuss technical topics regarding Deco products.
Deco

Tags

Label

 
Hi, My deco network has been fine for some time. I have an X60 connected to router and to a switch which is wired to other decos. Suddenly lost internet and reset router but now decos are green, app s
By Gerard50 · Latest post 2024-02-21 04:08:17 by Gerard50
0Helpful
47Views
2Replies
I upgraded my Deco system from M5 to X50. The problem I encountered with X50 is that I can't set the QOS bandwidth setting above 100Mbps. It seems its capped with that bandwidth. My current internet b
Bandwidth Control/QoS
By bleuken · Latest post 2024-02-21 04:05:25 by bleuken
2Helpful
189Views
4Replies
Hi, I have three Deco PX50's working with Starlink (with the Starlink router in bypass mode). All of my devices except the "main" Deco show PCL is being used via the Deco app. The device without PCL i
Starlinkpx50
By thelinkuser · Latest post 2024-02-20 22:57:12 by Alexmesh
0Helpful
353Views
17Replies
When there will be an firmware update for the v.1.2 of the deco x50 model ? The (older) v.1 model has already a new firmware with nice features like the eco-mode, where one can switch off the wlan ove
By Mr_AI · Latest post 2024-02-20 22:00:00 by Mr_AI
10Helpful
178Views
3Replies
I have a 3x setup of Deco AC1900 (S1900) configured in access point mode, with each Deco getting an IPv4 from my router (reservations set for each Deco unit, so their IPv4 address is persistent). Runn
Access Point ModeNetwork Connectivity
By dmmm05 · Latest post 2024-02-20 19:20:22 by dmmm05
1Helpful
236Views
9Replies
I currently have a 3-node mesh of Deco P9s working in AP mode and using Ethernet backhaul. I'm looking to add a fourth node and wondered whether I could add a single Deco X50 to the mesh and configure
Access Point ModeEthernet BackhaulPowerline Backhaul
By Vumad · Latest post 2024-02-20 19:08:43 by Vumad
2Helpful
157Views
5Replies
Hi Good Morning. I noticed for the V4 of the Deco E4 exists these features: New features: 1. Support for customizing Satellite Deco signal source. 2. Support for customizing Clients connection prefere
Firmware UpdateFeature Request
By Garpa
2Helpful
69Views
0Replies
I recently got the XE75 pro and it appears to be working fine to my Virgin Media v5 Hub. I've turned Wifi off on the hub and the XE75 is in AP mode. I'm wondering if it's better to flip the VM Hub int
Access Point Mode
By kitenski · Latest post 2024-02-20 12:59:53 by Alexandre.
1Helpful
110Views
1Replies
After the latest firmware update the deco continue to display Abnormal WAN Port speed and the download & upload speeds are capped at 94 Mbps. How can I at least downgrade to fix this issue? ISP suppor
Firmware Update
By SHN · Latest post 2024-02-20 12:03:26 by Braindeer
24Helpful
3636Views
24Replies
I Just switched to this router using 2x BE65 and an outdoor X50. I have all my IoT units connected on the Wifi IoT with no issues, however i also have two hubs. An SmartThings Hub connected on IoT wif
IoT NetworkMatterDevice IsolationEthernet
By NarkoKrig · Latest post 2024-02-20 09:26:48 by NarkoKrig
1Helpful
129Views
4Replies
1454647...
1454647...