Deco
network overview ISP ONU in bridge mode with Deco xe75 in router mode for Internet ISP is launching iptv with a different vlan the configuration sop provided by isp for route in onu details the follow
Network ConnectivityInstallationVLAN/IPTV
1Helpful
824Views
I have a new, Deco X50-4G working in router mode using a 4G Sim. I've then got 3 X50 mesh units connected to it either wirelessly or with ethernet backhaul. Standard wifi network works fine across the
Guest NetworkVLAN/IPTV
7Helpful
3182Views
Hi All, Just a quick question as I can not seem to find an answer to this. Can I use my Deco XE75 as a wifi router using PPPoE? I would connect directly with internet using an ethernet cable, not usin
VLAN/IPTV
0Helpful
1204Views
Hello. I recently purchased 3 deco x10 (one at a time) and connected them together in this way: I have 3 floors (including the garage. For simplicity I will number them in order starting from 1). the
Multi-GigabitConnection PreferenceDeco Ethernet BackhaulVLAN/IPTVPerformance
3Helpful
2483Views
Hey !! I have install again beta firmware to check IPTV bridge but still speed fluctuations problem but in beta firmware there is another problem is that i can't get WAN ip address immediately after r
Network ConnectivityVLAN/IPTV
By
ARGamingPK1
· Latest post 2024-10-31 19:39:32
by ARGamingPK1
1Helpful
1215Views
Why my ISP IPTV Box not work on first try after i reboot my Deco or when power supply went gone and the come back so the ISP IPTV Box stopped working on first try i have to reboot my IPTV Box again n
VLAN/IPTVIPTV
By
ARGamingPK1
· Latest post 2024-10-30 11:33:45
by ARGamingPK1
0Helpful
755Views
Hello I have 3 deco units... X58-4G as main/base unit. Works fine. Connected to fibre ONT with pppoe (vlan/iptv). Works great. My 2 x20 units... X20 (unit 1). Is ver 1.2 (V-NZ). I understand these are
Access Point ModeFirmware UpdateVLAN/IPTV
By
CameronWilks
· Latest post 2024-09-25 08:58:14
by CameronWilks
1Helpful
924Views
Hi all, Background: I have bought 2x units of X50-POEs and 1x unit of TL-SG108PE smart switch w/ POE. I am using the Deco X50-POE as the main router and therefore would like maintain my router in Rout
Network ConnectivityDeco Ethernet BackhaulVLAN/IPTVPoE
1Helpful
4079Views
I purchased the 4 Units of Deco M4 and setup the Unifi 500mbps PPOE and is successfully linked with WIFI. However, the test speed for Main Deco M4 is around 250mbps (50% of Unifi Speed of 500mbps). I
Network ConnectivityFirmware UpdateVLAN/IPTV
By
SylvesterChua
· Latest post 2024-06-25 09:58:27
by David-TP
0Helpful
1065Views
Hi everyone, i just changed my Singtel Wifi mesh to Deco x20 so far so good for the internet coverage, but my Singtel TV cannot get internet from Deco X20, when i try to enable the IPTV to Singapore-s
Network ConnectivityAccess Point ModeInstallationVLAN/IPTV
0Helpful
913Views
I really hope somebody can help me. I just bought this mesh router to replace my Verizon router. I've used Orbi in the past and this time I bought Deco because lots of reviews said it was great. I cur
Network ConnectivityVLAN/IPTVGuest Network
By
mosesh1185
· Latest post 2024-05-29 09:58:16
by mosesh1185
0Helpful
1034Views
hey Guys, I tried to setup an IPTV via my Deco M4 mesh system, as the TP Link powerline most likely died of age :) The problem I have is that the main Deco, which on LAN port 1 has ISP router connecti
VLAN/IPTV
By
Michaelslay90
· Latest post 2024-05-14 09:52:59
by Michaelslay90
1Helpful
2794Views