Business Community > Pharos Wireless Bridges > CPE 210 Problem
< Pharos Wireless Bridges

CPE 210 Problem

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

CPE 210 Problem

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
CPE 210 Problem
CPE 210 Problem
2018-01-30 01:14:22
Model :

Hardware Version :

Firmware Version :

ISP :

I just purchased a CPE 210 for the purpose of projecting wifi from my outdoor shop to my barn in order to set up some IP cameras. I'm having a lot of trouble getting it to work. I've tried to set it up both as an access point and as a repeater but whenever I try to connect a device to it after its been set up it gives me a password error (when I know the password is correct) or in the case when it's set up as a repeater the internet stops working all together. It seems to be my current modem/router and the CPE are squabbling over the IP.

Any advice?
  0      
 
  0      
 
#1
Options
5 Reply
Re:CPE 210 Problem
2018-01-30 19:16:59
Repeater mode is not recommended for outdoor Point to Point long range. Instead, configure an AP and a Client.

Basic Configuration:
1. Configure CPE210 in your outdoor shop as an Access Point and Configure the one on your barn side as a Client.
2. Set up a static IP address for both of them in the same subnet as the main router.

What's the distance between the shop and the barn?
Are there any obstacles(like trees, houses) between? Make sure a clear Line of Sight.
  0  
  0  
#2
Options
Re:CPE 210 Problem
2018-01-31 12:45:16
The distance between the two is only about 300 ft. I only purchased one, I thought I would be able to link it in to my existing internet in the shop and mount it outside (facing the barn) in order to project the wifi to where I need it.
  0  
  0  
#3
Options
Re:CPE 210 Problem
2018-01-31 17:00:08

mbtr22 wrote

The distance between the two is only about 300 ft. I only purchased one, I thought I would be able to link it in to my existing internet in the shop and mount it outside (facing the barn) in order to project the wifi to where I need it.


Not possible. Your client devices (smartphones, tablets, laptops) in the barn can't cover such a distance to the CPE due to the weak antennas of the client devices (not the CPE!) and if they could, you wouldn't need a CPE at all. Best solution would be two CPEs, one at your shop wired to your Internet router and the other one at your barn wired to another indoor access point, which distributes the signal locally to the clients. Also, a CPE510 (5 GHz band) would perform much better then a CPE510 in such a setup.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#4
Options
Re:CPE 210 Problem
2018-02-02 12:17:35
Tôi nghĩ rằng có thể! I think that it is possible!
  0  
  0  
#5
Options
Re:CPE 210 Problem
2018-02-06 16:00:14
informative post
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1315

Replies: 5

Related Articles
CPE 210 Problem
1161 0
CPE 210 Authentication Problem
1410 0
Outdoor CPE 210 Netgear Problem
586 0
Trouble with cpe 210
1726 0
Camera attached to CPE-210
1224 0
access point cpe 210 connection error
3853 0
About Us
Press
Copyright © TP-Link Corporation Limited. All rights reserved.