Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Connect M5 to another satellite M5 via daisy chain connection.

< Deco

Connect M5 to another satellite M5 via daisy chain connection.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Connect M5 to another satellite M5 via daisy chain connection.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Exia

2019-10-28 00:50:39 - last edited 2019-11-01 03:47:27

Posts: 3

Helpful: 4

Solutions: 0

Stories: 0

Registered: 2019-10-28

Connect M5 to another satellite M5 via daisy chain connection.

2019-10-28 00:50:39 - last edited 2019-11-01 03:47:27

Model: Deco M5

Hardware Version: V1

Firmware Version:

I just recently bought a Deco M5 (3 pack). I have the Main Deco setup as a router. I then have a 2nd Deco setup in my hallway. The 3rd Deco is a little further to the main Deco. The 2nd Deco is in between the main and 3rd Deco in terms of distance. However, I noticed that the 3rd Deco is not connecting to the 2nd Deco that is nearer. From the Deco app, I could see that the 3rd Deco is connected to the main Deco and the signal status is very weak. Devices connected to the 3rd Deco have very slow internet speed.

I thought the 3rd Deco is supposed to connect to a nearer Deco, in this case the 2nd Deco but it is not. How can I get the 3rd Deco to connect to the 2nd Deco? Will setting 1st Deco as AP (use back but old router) help? Or satellite Decos can only connect to main Deco and do not support Daisy chain?

1 Accepted Solution

Kevin_Z

2019-10-29 01:28:20 - last edited 2019-11-01 03:47:27

Posts: 21605

Helpful: 5050

Solutions: 2546

Stories: 21

Registered: 2018-12-24

Re:Connect M5 to another satellite M5 via daisy chain connection.-Solution

2019-10-29 01:28:20 - last edited 2019-11-01 03:47:27

@Exia

The Deco supports star network and daisy-chain network, so do not worry about that, the 3rd Deco can connect to the 2nd one.

From your description, it seems that the signal strength obtained by the 3rd Deco does not reach the threshold value which does not trigger the Deco switching between different Decos.

It is suggested to move the 1st Deco and 3rd Deco further away from each other, and try to reboot the whole network system.

And you can take longer time to verify whether it works well.

May it help and have a nice day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

Recommended Solution

3 Reply

47Cosmos

LV2

2019-10-28 05:23:04 - last edited 2019-10-28 18:02:55

Posts: 27

Helpful: 8

Solutions: 1

Stories: 0

Registered: 2019-08-27

Re:Connect M5 to another satellite M5 via daisy chain connection.

2019-10-28 05:23:04 - last edited 2019-10-28 18:02:55

In my case

1st node (router mode) - 2nd floor

2nd node (wifi) - 1st floor

3rd node (wifi) - G floor

at first the 3rd tried and connecedt to 1st node, but few hours or half day later it connected to 2nd node.

Exia

LV1

2019-10-28 06:48:20 - last edited 2019-10-28 18:02:55

Posts: 3

Helpful: 4

Solutions: 0

Stories: 0

Registered: 2019-10-28

Re:Connect M5 to another satellite M5 via daisy chain connection.

2019-10-28 06:48:20 - last edited 2019-10-28 18:02:55

@47Cosmos So the 3rd node can connect to the 2nd node? In that case, I'll try to leave them on a little longer and see. Thanks.

Kevin_Z

2019-10-29 01:28:20 - last edited 2019-11-01 03:47:27

Posts: 21605

Helpful: 5050

Solutions: 2546

Stories: 21

Registered: 2018-12-24

Re:Connect M5 to another satellite M5 via daisy chain connection.-Solution

2019-10-29 01:28:20 - last edited 2019-11-01 03:47:27

@Exia

The Deco supports star network and daisy-chain network, so do not worry about that, the 3rd Deco can connect to the 2nd one.

From your description, it seems that the signal strength obtained by the 3rd Deco does not reach the threshold value which does not trigger the Deco switching between different Decos.

It is suggested to move the 1st Deco and 3rd Deco further away from each other, and try to reboot the whole network system.

And you can take longer time to verify whether it works well.

May it help and have a nice day.

Connect M5 to another satellite M5 via daisy chain connection.

Connect M5 to another satellite M5 via daisy chain connection.

Information

Voters 1

Tags