Troubleshooting LED loop on Deco/ Deco stuck in solid yellow
This Article Applies to:
All Deco models
Typical Problem Description:
1. One of the Deco units was stuck in constant yellow light mode and was not able to enter setup mode (blue blinking light);
2. One of the Deco units goes into this reboot loop of Solid Yellow > Blinking Yellow > Blinking Blue > Off > Solid Yellow, this cycle keeps on repeating.
If Deco had a solid or flashing red, please have a look at this link: Deco turned red
Troubleshooting suggestions:
1. Please hold the reset pinhole at the bottom of the Deco for 1s and check whether the light could be back to yellow---flashing blue.
2. If the factory reset did not make any difference, please refer to this link to do a firmware recovery:
https://www.tp-link.com/support/faq/2958/
If the issue continues, please comment below with the following information:
1. The model number as well as the firmware version of the Deco;
2. Which problem description is more like your current issue?
3. Have you tried the hardware reset and firmware recovery suggestions? what are the results?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
1. The model number as well as the firmware version of the Deco;
Model: DECO E4R
SN: 22121N8A02866
2. Which problem description is more like your current issue?
One of the 2 DECO´s that I have has the "stuck in solid green/yellow" the led after all the suggestions
3. Have you tried the hardware reset and firmware recovery suggestions? what are the results?
Yes, and I have not any positive results
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community.
In this way, It is very likely this Deco is broken and I see the SN is still under warranty, you could contact the shop retailer to get it replaced.
Thank you very much.
Best regards.
--------------------------
Deco X50-PoE is ready for your advice. If you are interested, please help us complete the following survey.
- Copy Link
- Report Inappropriate Content
@TP-Link I don't like yellow. It annoys me.
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community.
May I know the model number of your Deco?
Have you tried the hardware reset and firmware recovery?
If neither helps, you could try to contact the local support team to check for warranty service.
Best regards.
- Copy Link
- Report Inappropriate Content
1. The model number as well as the firmware version of the Deco;
Deco X60 S/N Y215034A00377. Firmware is unknown, as I'm unable to make the device boot. I took it directly out of the box, and the problem started.
2. Which problem description is more like your current issue?
The device goes with a solid yellow light, then flashing blue, then it turns off and after that, it repeats the cycle.
3. Have you tried the hardware reset and firmware recovery suggestions? what are the results?
Yes, I've tried both in different computers, but Tftp tool doesn't get any logs in the mentioned tab, and if I try to do it without this tool, the computers can't access 192.168.0.1.
- Copy Link
- Report Inappropriate Content
Hi, my X20 v4 turns brick and stuck in solid yellow.
I have tried all the methods in https://www.tp-link.com/my/support/faq/2958/ but it doesnt seem to reset.
- Copy Link
- Report Inappropriate Content
Deco XE75
i don't know what firmware version it's on. I can't connect to it to check.
Tried the firmware recovery. When I power on the device while holding the reset button, the light starts on solid yellow, Flashes green twice and then to solid green. No internet access and no way to connect to it.
this is the second time it's happened within a year of purchasing. The replacement units you sent me have the same problem as the original I bought.
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community.
After Deco XE75 went into firmware recovery mode/solid green, have you tried
- Set a static IP address of 192.168.0.2/255.255.255.0 on the PC’s Ethernet adapter.
- On the PC, open a browser, access http://192.168.0.1
- upload the latest firmware Deco XE75(US)_V1_1.1.8 Build 20221121
This Deco will have no internet in firmware recovery mode and the PC also does not need internet to access its web UI at this moment.
I see your previous ticket record with Deco XE75 and it only mentioned the instability issue of satellite Deco XE75. The suggestions here in this post are more suitable when the hardware of Deco might be broken.
By the way, could you please lease me a private message of the MAC address of this satellite XE75?
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
Deco M5
Hardware Version: V3
S/N 22073K2A00066
Stuck on yellow and tried the fix from the refer link but its still in solid yellow. Is there any other way to fix it?
- Copy Link
- Report Inappropriate Content
Hi, I think you need to contact the local support team to ask for warranty service:
https://www.tp-link.com/ph/support/contact-technical-support/#Hotline-Support
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 49666
Replies: 51
Voters 0
No one has voted for it yet.