Deco M9 Plus | Signal Source Change possible

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Deco M9 Plus | Signal Source Change possible

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
20 Reply
Re:Deco M9 Plus | Signal Source Change possible
2021-08-07 13:34:53
Hi Please I would like to have the firmware too. I am using a hybrid of M9 Plus and M5. I need the firmware for these two models please…much appreciated
  0  
  0  
#12
Options
Re:Deco M9 Plus | Signal Source Change possible
2021-08-13 14:37:32

@TP-Link When will this be incorporated to a regular release? The beta is almost 6 months old. 

  0  
  0  
#13
Options
Re:Deco M9 Plus | Signal Source Change possible
2021-08-14 07:11:35

@TP-Link Can you send me the beta version as well? Thanks

  0  
  0  
#14
Options
Re:Deco M9 Plus | Signal Source Change possible
2021-10-25 03:11:06

@TP-Link Can you send me the firmware as well?  Have a house with 5 M9's.  Previously had 6 setup but was having all sorts of issues.  With 5 it's manageable but still have significant latency issues when doing anything over wifi.

  0  
  0  
#15
Options
Re:Deco M9 Plus | Signal Source Change possible
2021-12-09 01:53:40

@TP-Link 

I would also like to try the firmware for better signal source selection. Can you email me as well? I am using M9 Plus

  0  
  0  
#16
Options
Re:Deco M9 Plus | Signal Source Change possible
2022-01-26 20:44:52

@TP-Link Half year later - is it possible to receive it? Or to became public???

Frustrated Deco (X90, M9 Plus, M4R, E4) & Tapo (C200, C210) owner looking for solutions to use the investment in them. Expensive Plastic...
  0  
  0  
#17
Options
Re:Deco M9 Plus | Signal Source Change possible
2022-01-30 02:36:00

@TP-Link Please help. I have the M9 with the router my office on the second floor and both satellites in the room below. I have very slow wifi download slow speed even though I have over 400mps on my laptop. I check the M9 and it uses the channels with the most interference and avoids channels not in use. Not sure what I am doing wrong.  Firmware is upto date. I had a Netgear Nighthawk 7000 router before it crapped out. I was very happy with it and feel foolish falling for the M9 promise. 

  0  
  0  
#18
Options
Re:Deco M9 Plus | Signal Source Change possible
2022-01-31 10:33:54

@sparta1osu 

It is actually Debug firmware, not a Beta one.

 

I don't think Decos are Mesh at all. There are just TP-Link N300 with a cut-off, fancy UI and nice plastics outside.

I made a topic about that: https://community.tp-link.com/en/home/forum/topic/528536?page=1

 

Update an e-mail from now: "We are sorry that you are not happy with your product. If Deco did not meet your expectations, you should have chosen another product. We did not claim that Deco is the best option for your network topology."

Frustrated Deco (X90, M9 Plus, M4R, E4) & Tapo (C200, C210) owner looking for solutions to use the investment in them. Expensive Plastic...
  0  
  0  
#19
Options
Re:Deco M9 Plus | Signal Source Change possible
2022-03-31 04:24:52
Does this firmware still available? Having the same issues. Can I also have the firmware please
  0  
  0  
#20
Options
Re:Deco M9 Plus | Signal Source Change possible
2022-04-01 07:35:53

  @Johnynz 

Hi, thank you very much for the message and there is no beta firmware for Deco M9 plus yet.

Please refer to this link and send an email to support.forum@tp-link.com with the requested information and we could invite the engineers to help me re-select the signal source if necessary.

Manual Signal Source Selection on Deco

  0  
  0  
#22
Options