Home Network Community > Wi-Fi Routers > Can't access the internet in client mode
< Wi-Fi Routers

Can't access the internet in client mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
123

Can't access the internet in client mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
21 Reply
Re:Can't access the internet in client mode
2013-05-16 02:07:07

Matthew cook wrote

Please give a try as the following:
On WR702N's web page, go to DHCP, enter the LAN IP address of your wireless router into "default gateway" on the DHCP server page.
Don't forget to reboot the WR702N.
Then see if the computer able to automatically obtain an IP address.
Does this make any difference?


Nope. That didn't work either. I tried with both DHCP enabled and disabled, just in case.
  0  
  0  
#12
Options
Re:Can't access the internet in client mode
2013-05-16 02:31:41
Status Screen




OSX Network Settings
Manual




DHCP




Ping
TL-WR702N Internal




TL-WR702N External




OSX - Fails at internal, let alone external.


  0  
  0  
#13
Options
Re:Can't access the internet in client mode
2013-05-20 15:06:58
I think this is the same problem which I describe yesterday in post "Client mode - problem with some TV (e.g. SAMSUNG SMART TV)".
You cannot access Internet or other computers in network because ARP-Replays are wrongly translated by TL-WR702N (in Client/Bridge/Repeter mode) and that is why they are dropped by your YouView box (you have information "Host is down").

You need to wait until TP-Link change this in new firmware.
  1  
  1  
#14
Options
Re:Can't access the internet in client mode
2013-05-20 15:46:13

kkkk-kkkk wrote

I think this is the same problem which I describe yesterday in post "Client mode - problem with some TV (e.g. SAMSUNG SMART TV)".
You cannot access Internet or other computers in network because ARP-Replays are wrongly translated by TL-WR702N (in Client/Bridge/Repeter mode) and that is why they are dropped by your YouView box (you have information "Host is down").

You need to wait until TP-Link change this in new firmware.

Yup, on Saturday I listened to what was going on with Wireshark and I tend to agree. I can see when DHCP is enabled, the DHCP Discover message never gets broadcast further than the TL-WR702N. Similarly, when I manually assign an IP address, I can see my computer gratuitously requesting it's IP and I can even see both the TL-WR702N and my Belkin router asking who 192.168.1.10 is.

I've sent this data to support who say they're going to try and simulate this scenario in their lab today. If I hear anything from that I'll let you know.
  0  
  0  
#15
Options
Re:Can't access the internet in client mode
2013-05-21 15:18:09
Have you checked the DHCP Server of Belkin Router ..

The Belkin router should assign a DNS Server address to all of its Clients ..

It should be 8.8.8.8 or 8.8.4.4
  0  
  0  
#16
Options
Re:Can't access the internet in client mode
2013-05-21 15:40:58

navneet wrote

Have you checked the DHCP Server of Belkin Router ..

Yes, it's configured correctly and working fine.


The Belkin router should assign a DNS Server address to all of its Clients ..

It should be 8.8.8.8 or 8.8.4.4

The Belkin router assigns a DNS server of 192.168.1.1 (itself) to all of it's clients, it then forwards on the requests to 8.8.8.8/4.4.4.4
  0  
  0  
#17
Options
Re:Can't access the internet in client mode
2013-05-23 15:36:38
Hi all,

After a lot of communication with support, Wireshark dumps and ARP table hacks, the solution actually turned out to be very simple!

The TL-WR702N has a configuration option called 'WDS mode', changing this from Auto to 3 Addr solved all my problems. The computer connected is now assigned an IP via DHCP from my original router, and it is able to access both the internal network and the internet. Hopefully this solution helps some of you to.

It should be noted that the diagnostics page on the TL-WR702N is still unable to ping anything external to my network however.
  1  
  1  
#18
Options
Re:Can't access the internet in client mode
2013-06-02 18:42:53

Verbitan wrote

Hi all,

After a lot of communication with support, Wireshark dumps and ARP table hacks, the solution actually turned out to be very simple!

The TL-WR702N has a configuration option called 'WDS mode', changing this from Auto to 3 Addr solved all my problems. The computer connected is now assigned an IP via DHCP from my original router, and it is able to access both the internal network and the internet. Hopefully this solution helps some of you to.

It should be noted that the diagnostics page on the TL-WR702N is still unable to ping anything external to my network however.



This thread has definitely helped me resolve my problems. I had similar issues on TL-WA7510N in client mode. After ripping my hair out I came across this post. I was little optimistic first but gave it a go anyway. So I checked the WDS box under wireless settings and to my surprise I had Internet access.


Thank you Verbitan.
  0  
  0  
#19
Options
Re:Can't access the internet in client mode
2013-06-05 17:32:25
Thanks Verbitan & Bodski.
I think the logic behind this is that the main router which uses 3-add WDS mode won't talk properly with the TL-WR702N client which uses 4-add WDS mode.
So the problem is solved by changing the client to 3-add WDS mode to match the main router's.
BTW, the WDS mode selection must be available with the latest firmware, because i don't see it on mine. I will upgrade it and have a look.
  0  
  0  
#20
Options
Thanks
2014-02-11 23:51:44

bodski wrote

This thread has definitely helped me resolve my problems. I had similar issues on TL-WA7510N in client mode. After ripping my hair out I came across this post. I was little optimistic first but gave it a go anyway. So I checked the WDS box under wireless settings and to my surprise I had Internet access.


Thank you Verbitan.


I signed up to this forum to also thank you.

I was trying to connect a BT Home Hub 4 (HH4) and despite trying everything nothing was working. After changing the WDS to 3 Addr it connected straight away. Thanks again.
  0  
  0  
#21
Options
123
Related Articles
 can't connect to the internet in client mode
1589 0
 Can't access to Internet in access point mode
18450 0
I can't access Internet with my Archer AX3000
117 4
 Can't Access the Internet
723 0
 Can't access internet.
419 0
 Can't access internet
336 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.