Home Network Community > Wi-Fi Routers > Unable to Use XC220-G3 as main router for EASY MESH
< Wi-Fi Routers

Unable to Use XC220-G3 as main router for EASY MESH

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Unable to Use XC220-G3 as main router for EASY MESH

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Unable to Use XC220-G3 as main router for EASY MESH
Unable to Use XC220-G3 as main router for EASY MESH
2024-01-11 04:09:26
Tags: #EasyMesh
Model: General Product  
Hardware Version: V1
Firmware Version: 1.3.0 0.8.0 v6062.0 Build 230327 Rel.32753n

I'm trying to setup a EASY Mesh setup using XC220-G3 and with RC450 AC 1750 Mesh WIFI Extender, I could not able to add my devices to MESH Network.

 

Add mesh device never detected extenders, even I tried updating extenders with the latest firmware to support easy mesh and tried connecting, my extender says the main router doesn't support eazy mesh feature.

 

Can anyone help here? 

  0      
 
  0      
 
#1
Options
4 Reply
Re:Unable to Use XC220-G3 as main router for EASY MESH
2024-01-11 07:52:32 - last edited 2024-01-18 09:56:29

  @hopekiran 

 

It depends which HW version is your RE450 device. Only RE450 V4 supports Easymesh - details.

You can check the HW version on the device sticker - here.

In general when the main router is Onemesh capable but the satellite device is Easymesh capable a WPS method can be used to build the mesh.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#2
Options
Re:Unable to Use XC220-G3 as main router for EASY MESH
2024-01-11 13:33:03 - last edited 2024-01-11 13:46:26

Hi @terziyski, The main router supports only EasyMesh, and My Extender HW version is Ver:4.8

 

Main Router Hardware Version:XC220-G3 v1.0 0000000

  0  
  0  
#3
Options
Re:Unable to Use XC220-G3 as main router for EASY MESH
2024-01-11 14:32:46 - last edited 2024-01-11 15:07:02

  @hopekiran 

 

What about your range extender, is it TP-Link RE450 v4.8 ?

It has to be with the latest FW release I presume RE450(US)_V4.8_1.0.20 Build 230213, which supports Easymesh too.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#4
Options
Re:Unable to Use XC220-G3 as main router for EASY MESH
2024-01-13 10:38:19

  @hopekiran 

 

Same here! I have two different extenders that both support "easy mesh" but it is not recognized. RX700X and the 450 v.4.0 extender. 

 

 

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 732

Replies: 4

Tags

EasyMesh
Related Articles
 Configurar router XC220-G3V
179 0
Unable to login to EB810v BE22000 device configuration page
707 0
xc220-g3v v2.30 VOIP registration Failure
4093 0
xc220-g3v v2.30 VOIP one-way audio
1120 0
 I am not able to connect any easy mesh device using lane cable on my tp link xc220-g3v V2.30
585 0
 TP LINK XC220 G3V
2466 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.