Official Release Deco X10_1.2.0 Added VPN, IoT network and Wi-Fi Access Control
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
This Article applies to
Deco X10_V1_1.1.7
Firmware Modifications and Bug Fixes:
- Added Static Route.
- Added the ability to customize the MTU.
- Added IoT network.
- Added VPN Server/Client
- Added Camera Security
- Added Whitelist/ Wi-Fi Access Control
- Added notification for Ethernet connection speed.
- Supported Captive Portal for Guest Network
- Supported TSS (TP-Link Simple Setup) Auto Discovery & Quick Configuration
- Added Firmware Auto Update.
- Supported Matter
- Supported KLAP protocol for Tapo smart devices
- Advanced Parental Control subscription added APP block/App Time Limits feature, which supports 2000+ applications.
- Improved Network performance and system stability;
- Fixed the bug that the device name is different in the Deco APP and the Web management page.
Firmware Download Link:
| Deco X10_V1 | 1.2.0 Build 20250306 | Newly updated to 1.10.0 Platform |
Update Advice:
- How to update the firmware via web UI.
- Firmware recovery is needed if users want to revert to the official 1.1.7: How to Downgrade Deco
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Has the ECO MODE feature in firmware 1.2 been cancelled?
Currently my MESH network only contains two X10s, both with firmware 1.2
But I can't find the ECO MODE option in the DECO APP?
- Copy Link
- Report Inappropriate Content
Hi, thank you very much for the feedback.
After confirming with the engineer, Deco X10-1.2.0 doesn't include ECO mode.
Best regards.
- Copy Link
- Report Inappropriate Content
But the situation is still the same, currently all clients can connect to the network normally, but no client can be seen in the deco app.
I'm experiencing the same issue and had posted the issue on the M9Plus firmware update thread thinking that was what was causing it. I've got 2x satellite M9Plus connected to an X10 in Access Point mode. See image below.
TL;DR The clients cannot be seen in the Android Deco app, but they are listed when viewed through the web interface of the X10.
See https://community.tp-link.com/en/home/forum/topic/810406?replyId=1561950
- Copy Link
- Report Inappropriate Content
Hi, thank you very much for the feedback.
Could you please also refer to this link to help me submit the Deco APP log:
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
David-TP wrote
Hi, thank you very much for the feedback.
Could you please also refer to this link to help me submit the Deco APP log:
Wait for your reply.
Best regards.
Thanks for responding! I've submitted the Deco app log thru the method above already.
- Copy Link
- Report Inappropriate Content
Hi, did you receive my message?
And it is also suggested to install the beta firmware here for the Deco M9 Plus to see whether it helps with the current issue:
Weak Signal on the Satellite Deco after updating Deco M9 Plus to 1.8.1
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP
No, haven't received anything from you other than the reply above. I'll try installing the beta firmware to see if it fixes clients not being shown.
David-TP wrote
Hi, did you receive my message?
And it is also suggested to install the beta firmware here for the Deco M9 Plus to see whether it helps with the current issue:
Weak Signal on the Satellite Deco after updating Deco M9 Plus to 1.8.1
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
David-TP wrote
And it is also suggested to install the beta firmware here for the Deco M9 Plus to see whether it helps with the current issue:
Weak Signal on the Satellite Deco after updating Deco M9 Plus to 1.8.1
I've upgraded the M9Plus with the beta firmware above, 1.8.1 Build 20250605 Rel. 63802, and it has not fixed the problem of clients not showing up in the client list.
- Copy Link
- Report Inappropriate Content
Hi, thank you very much for the update.
In this way, I'd like to forward your case to the senior engineer for further assistance.
Please check your email later for more suggestions.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi @David-TP !
I received an email from TPLink Support with a new X10 beta firmware, 1.2.0 Build 20250609 Rel. 56423, to test and this has fixed the problem with the clients not appearing in the Android Deco app. I've replied that email, but am also replying here for closure. Thanx for the help !
David-TP wrote
Hi, thank you very much for the update.
In this way, I'd like to forward your case to the senior engineer for further assistance.
Please check your email later for more suggestions.
Best regards.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 3
Views: 3359
Replies: 22
Voters 2
