Home Network Community > 3G/4G Routers/MiFi > MR200 IPSEC VPN Will Not Passthough
< 3G/4G Routers/MiFi

MR200 IPSEC VPN Will Not Passthough

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12345

MR200 IPSEC VPN Will Not Passthough

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
MR200 IPSEC VPN Will Not Passthough
MR200 IPSEC VPN Will Not Passthough
2016-08-22 02:43:08 - last edited 2020-08-28 08:45:39
Model :

Hardware Version : Not Clear

Firmware Version :

ISP :

My MR200 is great except it wont passthrough the IPSEC traffic of my Cisco VPN or VPN Unlimited clients on different machines.
I have updated the firmware via the web but no change.
Looking around this problem seems to have been around for a while, I can't understand why TP-Link haven't fixed this.


Firmware Version:0.9.1 0.0 v004a.0 Build 160412 Rel.38588n

Hardware Version:Archer MR200 v1 00000001

 Available Solution
  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:MR200 IPSEC VPN Will Not Passthough-Solution
2020-08-15 14:02:56 - last edited 2020-08-28 08:45:39

@coatsdarlingto finally I found a way that fix this issue however its look a little like strange!

 

Follow the below steps:

 

  1. Download the v160412 firmware from the https://static.tp-link.com/res/down/soft/Archer_MR200(EU)_V1_160412.zip and update your device.
  2. After reboot, download v160706 firmware from here https://static.tp-link.com/res/down/soft/MR200_V1_Beta_160706.zip and try to update it again.
  3. As you know the error may be appeared at the previous step and before rebooting, so cancel the process and manually reboot the device by clicking on reboot icon at top right corner of web page.
  4. Now update the device to v160412 firmware aging and let it to reboot also.
  5. After rebooting, check the firmware version, now your device updated to the 0.9.1 0.0 v004a.0 Build 160706 Rel.40546n firmware!


I hope these steps could help you and others.

 

Please LIKE if you find this useful...

Recommended Solution
  2  
  2  
#53
Options
50 Reply
Re:MR200 IPSEC VPN Will Not Passthough
2016-09-03 18:10:24
Exactly same problem - vpn tunnel connected but no traffic - I have tried a travel router over the same network without problems so definitely a mr200 issue - can tplink issue a fix?
  0  
  0  
#2
Options
Re:MR200 IPSEC VPN Will Not Passthough
2016-09-06 04:28:15
I have the same issue using ShrewSoft VPN client. VPN tunnel connected, but no traffic. Same VPN trough same 4G connection works fine.
  0  
  0  
#3
Options
Re:MR200 IPSEC VPN Will Not Passthough
2016-09-13 04:43:46
Same issue, same versions etc. May need to return the item for refund as the device support doesn't appear to be very good.
  0  
  0  
#4
Options
Re:MR200 IPSEC VPN Will Not Passthough
2016-09-28 17:34:40
I installed OPENVPN successfully as a bypass, waiting for a working firmware for this device. A lot of other issues. Support inefficient
  0  
  0  
#5
Options
Re:MR200 IPSEC VPN Will Not Passthough
2016-09-30 19:11:11
Same issue on my site. I try to use the MR200 only as a modem in front of my actual DHCP and another Cisco router managing the VPN tunnel. Using this setup already for long time with ADSL and LTE router without problems. All my attempts to find a workaround by configuring port forwarding etc. failed. Please fix the problem, it is not a cheap router to just collect dust in my office.

Firmware Version:0.9.1 0.0 v004a.0 Build 160412 Rel.38588n Hardware Version:Archer MR200 v1 00000000 IMEI:867787020739961

Thanks
  0  
  0  
#6
Options
Re:MR200 IPSEC VPN Will Not Passthough
2016-11-02 15:48:57
Same problem, even after upgrading firmware to V 5/9/2016. Passthrough is enabled. Tunnel is established (welcome banner is shown) but no traffic whatsoever. Can't even Google with tunnel up.

VPN=IPSEC, which works fine everywhere else.

Please fix!
  0  
  0  
#7
Options
MR200 IPSEC VPN Will Not Passt
2016-12-11 15:26:00
HelloDoes anyone know if it is possible to install a cisco ipsec VPN client on the stora? not totally sure about the name Thanks in advance
  0  
  0  
#8
Options
Re:MR200 IPSEC VPN Will Not Passthough
2016-12-21 06:15:44
Hello
I have been using a beta update for the MR200, which you should find is available through tp link support.
It did fix the problems I was having with l2tp and ipsec.
  0  
  0  
#9
Options
Re:MR200 IPSEC VPN Will Not Passthough
2016-12-21 16:05:07

newfoundglory wrote

Hello
I have been using a beta update for the MR200, which you should find is available through tp link support.
It did fix the problems I was having with l2tp and ipsec.


I received those as well. The zip I received contains three .bin files and some instructions (PDF). They told me each .bin is for a different VPN protocol. I have asked them (twice) which one to use for IPSEC, not getting any response. Which one did you install to fix your IPSEC connection? Also, did you follow any of the instructions in the PDF? Thanks!

Archer MR200v1_0.9.1_1.1_up_boot(160707)_2016-07-07_09.43.10.bin
MR200v1_0.9.1_0.0_up_boot(151230)_15.30.09_fix_pptp.bin
MR200_up_boot_2016-07-06_11.32.53.bin
  0  
  0  
#10
Options
Re:MR200 IPSEC VPN Will Not Passthough
2016-12-21 16:10:51
Its none of those.

Its beta 161026, file starts

Archer_MR200v1_0.9.1_1.1_up_boot(161026)
  0  
  0  
#11
Options
12345

Information

Helpful: 0

Views: 13212

Replies: 50

Related Articles
Archer MR200 v1 IPSEC VPN passthrough still not working despite beta firmware
223 1
MR200 v1 doesn't passthrough IPSec VPN traffic
3220 1
MR200 v1 IPSec passthrough problems
1676 0
About Us
Press
Copyright © TP-Link Corporation Limited. All rights reserved.