FAIL to adopt EAP 110 outdoor

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

FAIL to adopt EAP 110 outdoor

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
FAIL to adopt EAP 110 outdoor
FAIL to adopt EAP 110 outdoor
2017-07-17 16:28:34
Model :

Hardware Version :

Firmware Version :

ISP :

Hi
1. Installed EAP 110 according to Installation Guide - it got it's DHCP IP address, seemed to work fine
2. Downloaded and installed EAP Controller on my Win10 PC
3. Created admin-login and passwd, Web interface for EAP Controller works just fine
4. Under "Access Points" : found the freshly installed EAP 110 with status "Pending"
5. Tried to Adopt : error : AP to be adopted doesn't exist !?

What can I do to adopt the EAP 110 ?
Thanks
  0      
  0      
#1
Options
15 Reply
Re:FAIL to adopt EAP 110 outdoor
2017-07-17 20:17:17
Use the EAP Discovery Utility to manually adopt the EAP. Usually you should not configure the EAP110 in stand-alone mode if you plan to manage it using the EAP controller. It is either to be controlled via EAP controller or in stand-alone mode (via the Web UI), but not both at the same time.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#2
Options
Re:FAIL to adopt EAP 110 outdoor
2017-07-17 22:15:57
Thanks R1D2 - that solved the problem ! 8-)
  0  
  0  
#3
Options
Re:FAIL to adopt EAP 110 outdoor
2019-11-14 23:20:08

@R1D2 please help me! I bought my eap 110 outdoor last week. I can't adopt my ap. I connect it directly to the router and the computer also connected to the router directly. I searched and tried everything I read in the net including turning off the firewall. Still it is not working. I tried to use mobile app and it is working but in controller it is not working.

  0  
  0  
#4
Options
Re:FAIL to adopt EAP 110 outdoor
2019-11-14 23:23:39
Firmware version is 3.0. Controller version is 3.2.1
  0  
  0  
#5
Options
Re:FAIL to adopt EAP 110 outdoor
2019-11-15 00:32:06

@Em0gurl31 

 

Here are some suggestions for you:

1. You say both your Controller host (PC) and the EAP110-Outdoor connect to the router, so they should be in the same subnet. Are you connecting the PC to the router via an ethernet cable? If not, please try it.

2. Can you ping the EAP device successfully on the Controller host? Does the EAP show on the management page of the Controller?

3. You say you cannot adopt the EAP device, what's the detailed phenomenon? If possible, please try to reset the EAP and adopt it again. 

4. By the way, you say the firmware version is 3.0, so is it EAP110-Outdoor V3.0? Please upgrade to the latest firmware (3.3.0 Build 20190301).

  0  
  0  
#6
Options
Re:FAIL to adopt EAP 110 outdoor
2019-11-15 00:55:02 - last edited 2019-11-15 01:17:39

 

Em0gurl31 wrote

I tried to use mobile app and it is working but in controller it is not working.

 

Em0gurl31, there are several things to try in case of problems with adopting. All methods require that you first do a factory reset (press the RESET button of EAP110 for 5 to 7 sec. until the LED starts blinking). Also turn off virus scanners in addition to the firewall if using Windows.

 

First method is connecting the EAP110 to the switch or router of the network the controller is runing in.

 

If this does not work, try second method using EAP Discovery Utility. Download the software from the TP-Link site here. Look up the IP of the PC running the controller, write it down. Shut down the controller and start the Discovery Utility. It should list the EAP110 and let you set the IP of the EAP, which is saved in flash memory. If done, exit the Discovery Utility and start the controller again. Now EAP110 should appear as pending.

 

First method works on layer 2 discovery, while second method works on layer 3.

 

If both methods don't work, there might be some problem with your Windows setup. You could check for services either blocking or using the ports required by Omada Controller (TCP/UDP ports 29810-29813, TCP port 8088, TCP port 8043).

 

Hope this helps.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#7
Options
Re:FAIL to adopt EAP 110 outdoor
2019-11-15 00:58:25

@forrest it is connected through ethernet. I also tried to reset my AP before. The firmware version is 3.3.0. 

  0  
  0  
#8
Options
Re:FAIL to adopt EAP 110 outdoor
2019-11-15 01:05:22

@forrest  the eap also showing to the controller but it is in pending Aps

File:
15737798364714947760898385900916.jpgDownload
  0  
  0  
#9
Options
Re:FAIL to adopt EAP 110 outdoor
2019-11-15 04:06:23

@R1D2 ok sir thanks a lot! I'll inform you once I did all your instructions thanks!

  0  
  0  
#10
Options
Re:FAIL to adopt EAP 110 outdoor
2019-11-15 05:58:29

@R1D2 sorry sir im not an IT expert. I can't understand some of your instructions especially setting the IP of the EAP. second is the layer 2 and layer 3. And lastly I don't know how to check the ports TCP and UPD. 

  0  
  0  
#11
Options

Information

Helpful: 0

Views: 6769

Replies: 15