Gateways
Downloaded Export Address Reservation is file list (CSV) empty, no items in the spreadsheet . The Table displays two pages of address reservations 123 total. I use the info as a backup and keep curren
0Helpful
123Views
I recently went from pre-2.3 firmware to 2.3.3 firmware on ER605. I believe this issue is related to the updated user interface so I think it affects any firmware with new user interface. When trying
UI
2Helpful
484Views
Hello, Since the new fw upgrade was released the backup wan is reported as offline, i can`t run speed test on wan 4 but ping from wan4 its ok. At this moment i don`t know if load balancing and failove
WAN SetupNetwork ConnectivityLoad Balancing
By
DonLeonhard
· Latest post Friday
by Gabriel-TP
0Helpful
99Views
Unfortunately none of the following actiion work when I tried to reset my gateway. I tried: pressing reset for 10s pressing reset for 30s pressing reset, power on and hold for 10s 30-30-30 (pressing r
By
mma678
· Latest post Friday
by Gabriel-TP
2Helpful
127Views
I have 2 ER605 routers, one v2.0 and the other v2.20. Both are on the same LAN, but different subnets, and only the v2.0 is controlled by the OC200 controller. The v2.20 has firmware 2.3.3, while the
ER605
By
MrTom
· Latest post Friday
by Vincent-TP
1Helpful
706Views
I am trying to use an ER605 as a gateway for two industrial Ethernet sensors that both have the same fixed factory IP address. The router receives traffic from the sensor port, but I cannot successful
VLAN & Multi-NetworksWAN SetupNATRouting
By
Krusing
· Latest post Friday
by Gabriel-TP
0Helpful
313Views
Buenas noches. He adquirido un TL-ER7206 y no conectan los ISP. En Wan1 con ip estática conecta y a los segundos desconecta. En Wan 2 tengo con PPPoE directamente no conecta. Actualmente estoy usando
WAN SetupNetwork Connectivity
By
KNet_Jorge
· Latest post Friday
by Vincent-TP
0Helpful
348Views
ER707-M2 v1.20 running 1.4.1 Build 20260325 Rel.78146 Local management. No Controller. Load Balance - On. tried Lower weight on Wan1 and Higher on WAN/LAN2 (reversed, same result) tried Enable Applica
By
Tarkin
· Latest post a week ago
by Vincent-TP
1Helpful
313Views
Device: ER7212PC V2.20 Firmware before (working): 2.3.1 Build 20260117 Firmware after (broken): 2.4.2 Build 20260411 Controller: Omada 6.2.0.20 Issue: After upgrading to firmware 2.4.2, mDNS proxy no
Firmware UpdatemDNSVLAN & Multi-Networks
By
brute4c
· Latest post a week ago
by Gabriel-TP
0Helpful
140Views
Its been almost 3 months since the first prereleases of 6.2 and the transition to stable and then on to 6.2.10.x And we are still waiting for ER8411 adapted firmware...I see ER605 got its build today,
By
GRL
· Latest post a week ago
by Vincent-TP
6Helpful
356Views
Hello. I have updated firmware within the last three weeks and I am trying to enable IPV6. After a lot of searching I have seen screengrabs (including from on here) which show a simple line under "gen
IPv6
By
MarkTee
· Latest post a week ago
by Gabriel-TP
0Helpful
1000Views
Need help kinda confused: so i have the TP Link ER605 V2.0 that shows in my screen shoot below. But when i check under where the serial number is i get the following: Model: ER605(UN) Ver. 2.6 i am no
Firmware Update
By
Stitch177
· Latest post a week ago
by Gabriel-TP
1Helpful
280Views