Восстановление прошивки маршрутизатора
Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.Восстановление прошивки маршрутизатора
Посты: 992
Полезный: 8
Решения: 0
Истории: 0
Дата регистрации: 2011-05-24
2013-07-22 15:20:48
Посты: 992
Полезный: 8
Решения: 0
Истории: 0
Дата регистрации: 2011-05-24
Восстановление прошивки маршрутизатора
2013-07-22 15:20:48
Теги:
Эта инструкция относится к моделям: TL-WDR4300ND, TL-WDR3600ND, TL-MR3420v2, TL-MR3220v2,TL-WR941NDv5, TL-WR940NDv2,TL-WR842ND, TL-WR1042ND а также TL-WR841NDv8,TL-WR740Nv4, Archer C7 v2
Если вы испытываете проблемы с запуском маршрутизатора(повреждённая прошивка, невозможность зайти на веб-интерфейс настроек) и стандартные средства не помогают(перезагрузка или сброс до заводских настроек), вы можете попробовать выполнить следующие шаги по восстановлению.
Для этого зайдите в Пуск – Панель управления – Центр управления сетями и общим доступом – Изменение параметров адаптера.
Щёлкните правой кнопкой на Подключение по локальной сети и выберите Свойства. Там выберите Протокол Интернета версии 4, дважды щёлкнув.
Выберите Использовать следующий IP адрес и введите:
IP адрес – 192.168.0.66 - для моделей TL-WR740V4,TL-WR841NDV8,TL-WR842NDV2,TL-WR941NDV5,TL-MR3220V2,TL-MR3420V2,TL-WDR3600,TL-WDR4300,ArcherC7
IP адрес – 192.168.1.66 - для моделей TL-WR842NDV1,TL-WR1042NDV1
Маска подсети – 255.255.255.0
Скачать утилиту TPTP-сервер tftpd32.450.zip
Прошивка восстановления – это любая прошивка для вашей аппаратной версии устройства, не содержащая слова boot в названии.
Рекомендуемая прошивка для восстановления:
wdr4300v1_ru_3_13_23_up(130506).bin
Неправильная прошивка:
wdr4300v1_ru_3_14_1_up_boot(141208).bin
Правильная прошивка:
wdr4300v1_ru_3_13_23_up(130506).bin
Переименуйте правильную прошивку: модельверсия_tp_recovery.bin
Пример для TL-WDR4300ND:
Запустите утилиту TFTP-сервер от имени администратора(щёлкните правой кнопкой и выберите Запуск от имени Администратора).
В поле Current directory(Текущее месторасположение) выберите папку, куда вы положили утилиту и переименованную прошивку.
В поле Server interface(Интерфейс сервера) у вас должен быть IP адрес вашего компьютера, который вы прописали в 1 шаге.
После загрузки прошивки маршрутизатор перезагрузится, верните в свойствах подключения по локальной сети автоматическое получение IP адреса и попробуйте зайти на веб-интерфейс настроек маршрутизатора.
Альтернативный вариант от пользователя
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Подписаться
- Добавить в закладки
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
63 Ответить
Посты: 1
Полезный: 0
Решения: 0
Истории: 0
Дата регистрации: 2018-02-20
Re: Восстановление прошивки маршрутизатора
2018-02-20 10:21:52
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 385
Полезный: 13
Решения: 1
Истории: 0
Дата регистрации: 2017-12-08
2018-02-22 05:59:29
Посты: 385
Полезный: 13
Решения: 1
Истории: 0
Дата регистрации: 2017-12-08
Re: Восстановление прошивки маршрутизатора
2018-02-22 05:59:29
[quote="Lobotr9Is"]прошу помощи, у меня устройство tl-wa850re слетела прошивка, немогу восстановить ,может кто подскажет по моей модельке скорость rs232 и нюансы связанные с моим устройством[/quote]Такую информацию вряд ли вам тут подскажут, т.к. она отсутствует в Datasheet.
Вам проще будет обратиться в сервисный центр.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 3
Полезный: 0
Решения: 0
Истории: 0
Дата регистрации: 2018-07-15
Re: Восстановление прошивки маршрутизатора
2018-07-15 10:01:15
First 0x2 last 0x7c sector size 0x10000 124
Erased 123 sectors
Copy to Flash... write addr: 9f020000
done Ребут и по новой загрузка.
Если закрыл прогу, то идет загрузка системы. И последняя команда "restarting system". Куда копать? Получается, что система дает команду рестарта?
Лог putty:
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wdr4300v1_tp_recovery.bin'.
Load address: 0x80060000
Loading: T T ## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting Atheros AR934x
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc v ersion 4.3.3 (GCC) ) #1 Mon Dec 8 14:46:23 CST 2014
[ 0.000000] Ram size passed from bootloader =128M
[ 0.000000] flash_size passed from bootloader = 8
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=s quashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6848k(rootf s),128k(config),64k(ART) mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 112896k/131072k available (1856k kernel code, 17996k rese rved, 432k data, 120k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
[ 0.096000] Mount-cache hash table entries: 512
[ 0.096000]
[ 0.096000] ****************ALLOC***********************
[ 0.096000] Packet mem: 8026e4c0 (0xe00000 bytes)
[ 0.096000] ********************************************
[ 0.096000]
[ 0.096000] NET: Registered protocol family 16
[ 0.096000] PCI init:ath_pcibios_init
[ 0.096000] ath_pcibios_init(294): PCI CMD write: 0x356
[ 0.096000] registering PCI controller with io_map_base unset
[ 0.096000] bio: create slab <bio-0> at 0
[ 0.096000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.096000] pci 0000:00:00.0: PME# disabled
[ 0.096000] Returning IRQ 64
[ 0.100000] NET: Registered protocol family 2
[ 0.100000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.100000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.100000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.100000] TCP reno registered
[ 0.100000] NET: Registered protocol family 1
[ 0.100000] ATH GPIOC major 0
[ 0.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.100000] msgmni has been set to 220
[ 0.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 54)
[ 0.100000] io scheduler noop registered
[ 0.100000] io scheduler deadline registered (default)
[ 0.100000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.104000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.104000] console [ttyS0] enabled
[ 0.404000] PPP generic driver version 2.4.2
[ 0.408000] NET: Registered protocol family 24
[ 0.412000] 5 cmdlinepart partitions found on MTD device ath-nor0
[ 0.416000] Creating 5 MTD partitions on "ath-nor0":
[ 0.424000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.428000] 0x000000020000-0x000000120000 : "kernel"
[ 0.432000] 0x000000120000-0x0000007d0000 : "rootfs"
[ 0.440000] 0x0000007d0000-0x0000007f0000 : "config"
[ 0.444000] 0x0000007f0000-0x000000800000 : "ART"
[ 0.448000] ->Oops: flash id 0xef4017 .
[ 0.452000] ----TP IGMP has been init------
[ 0.456000] TCP cubic registered
[ 0.460000] NET: Registered protocol family 10
[ 0.468000] NET: Registered protocol family 17
[ 0.472000] 802.1Q VLAN Support v1.8 Ben Greear <
[ 0.476000] All bugs added by David S. Miller <
[ 0.484000] athwdt_init: Registering WDT success
[ 0.488000] ath_otp_init: Registering OTP success
[ 0.492000] ath_clksw_init: Registering Clock Switch Interface success
[ 0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.516000] Freeing unused kernel memory: 120k freed
init started: BusyBox v1.01 (2014.12.08-06:50+0000) multi-call binary
This Board use 2.6.31
insmod: cannot open module `/lib/modules/2.6.31/kernel/x_tables.ko': No such fil e or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xt_tcpudp.ko': No such fi le or directory
[ 1.684000] xt_time: kernel timezone is -0000
[ 1.884000] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 1.888000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 1.896000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 1.904000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.340000] ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
[ 2.732000] PPPoL2TP kernel driver, V1.0
[ 2.756000] PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
(none) mips #1 Mon Dec 8 14:46:23 CST 2014 (none)
(none) login: [ 5.096000] restoring factory default...
[ 6.992000] Now flash open!
[ 6.996000] Read from 0X20000 to 0X20120: OK
[ 7.524000] Now flash open!
[ 7.528000] Read from 0X7D0000 to 0X7E21D8: OK
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_0=0x00000000
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_1=0x00000000
[ucVlanCfg_init, 92]Prepare paramter :vlanEntry_2=0x00000000
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_3=0x0000 0000
[ucVlanCfg_init, 95]VLAN CFG PARAM STR:vlanEnable=0 vlanEntry_0=0 vlanEntr y_1=0 vlanEntry_2=0 vlanEntry_3=0
[ 8.040000] ATHR_GMAC: Length per segment 1 536
[ 8.044000] ATHR_GMAC: fifo cfg 3 01f00140
[ 8.048000] ATHR_GMAC: RX TASKLET - Pkts per Intr:100
[ 8.052000] ATHR_GMAC: Mac address for unit 0:bfff0000
[ 8.056000] ATHR_GMAC: ff:ff:ff:ff:ff:ff
[ 8.612000] ATHR_GMAC: Max segments per packet : 1
[ 8.616000] ATHR_GMAC: Max tx descriptor count : 128
[ 8.620000] ATHR_GMAC: Max rx descriptor count : 128
[ 8.628000] ATHR_GMAC: Mac capability flags : 2381
[ 8.644000] athr_gmac_ring_alloc Allocated 2048 at 0x87b1f000
[ 8.648000] athr_gmac_ring_alloc Allocated 2048 at 0x87aca800
[ 8.956000] WASP ----> S17 PHY *
[ 8.956000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 8.964000] [VLAN_CONFIG] vlanEnable:Disable
[ 8.968000] [VLAN_CONFIG] Aborting VLAN CONFIG!
[ 9.040000] Hello, nat module!
[ 9.044000] thread: napt_ct_scan create success pid:120
[ 9.048000] netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
[ 9.056000] isis_ip_intf_entry_add id[0] for vid[1]
[ 9.064000] isis_ip_intf_entry_add id[1] for vid[2]
[ 9.068000]
[ 9.068000] ######## S17 SSDK init succeeded! ########
[ 9.080000] [VLAN_MNGR] Registering: VID= 1 Member=001355d0 Policy=0 cookie =000000c8 desc=VLAN 1 For LAN OK
[ 9.092000] [VLAN_MNGR] Registering: VID= 2 Member=001bff50 Policy=0 cookie =000000c8 desc=VLAN 2 For WAN OK
[ 9.104000] ++++ athrs17_igmp_setup once
[ 9.108000] [VLAN_MNGR] Registering: VID= 4 Member=0013fdd0 Policy=3 cookie =87bc1100 desc=IGMP SNOOPING VTBL OK
[ 9.120000] [VLAN_MNGR] Registering: VID= 8 Member=0013f7d0 Policy=3 cookie =87bc1104 desc=IGMP SNOOPING VTBL OK
[ 9.128000] [VLAN_MNGR] Registering: VID= 12 Member=0013f5d0 Policy=3 cookie =87bc1108 desc=IGMP SNOOPING VTBL OK
[ 9.140000] [VLAN_MNGR] Registering: VID= 16 Member=0013dfd0 Policy=3 cookie =87bc110c desc=IGMP SNOOPING VTBL OK
[ 9.152000] [VLAN_MNGR] Registering: VID= 20 Member=0013ddd0 Policy=3 cookie =87bc1110 desc=IGMP SNOOPING VTBL OK
[ 9.160000] [VLAN_MNGR] Registering: VID= 24 Member=0013d7d0 Policy=3 cookie =87bc1114 desc=IGMP SNOOPING VTBL OK
[ 9.172000] [VLAN_MNGR] Registering: VID= 28 Member=0013d5d0 Policy=3 cookie =87bc1118 desc=IGMP SNOOPING VTBL OK
[ 9.180000] [VLAN_MNGR] Registering: VID= 32 Member=00137fd0 Policy=3 cookie =87bc111c desc=IGMP SNOOPING VTBL OK
[ 9.192000] [VLAN_MNGR] Registering: VID= 36 Member=00137dd0 Policy=3 cookie =87bc1120 desc=IGMP SNOOPING VTBL OK
[ 9.204000] [VLAN_MNGR] Registering: VID= 40 Member=001377d0 Policy=3 cookie =87bc1124 desc=IGMP SNOOPING VTBL OK
[ 9.212000] [VLAN_MNGR] Registering: VID= 44 Member=001375d0 Policy=3 cookie =87bc1128 desc=IGMP SNOOPING VTBL OK
[ 9.224000] [VLAN_MNGR] Registering: VID= 48 Member=00135fd0 Policy=3 cookie =87bc112c desc=IGMP SNOOPING VTBL OK
[ 9.236000] [VLAN_MNGR] Registering: VID= 52 Member=00135dd0 Policy=3 cookie =87bc1130 desc=IGMP SNOOPING VTBL OK
[ 9.244000] [VLAN_MNGR] Registering: VID= 56 Member=001357d0 Policy=3 cookie =87bc1134 desc=IGMP SNOOPING VTBL OK
[ 9.256000] [VLAN_MNGR] Registering: VID= 60 Member=001355d0 Policy=3 cookie =87bc1138 desc=IGMP SNOOPING VTBL OK
[ 9.276000] [VLAN_MNGR] <00> Flushing VLAN Table.
[ 9.284000] [VLAN_MNGR] <01> Creating VLAN VID= 1 Member=001355d0 Desc:VLAN 1 For LAN
[ 9.292000] [VLAN_MNGR] <02> Creating VLAN VID= 2 Member=001bff50 Desc:VLAN 2 For WAN
[ 9.300000] [VLAN_MNGR] <03> Creating VLAN VID= 3 Member=0013fdd0 Desc:IGMP SNOOPING VTBL
[ 9.312000] [VLAN_MNGR] <04> Creating VLAN VID= 4 Member=0013f7d0 Desc:IGMP SNOOPING VTBL
[ 9.320000] [VLAN_MNGR] <05> Creating VLAN VID= 5 Member=0013f5d0 Desc:IGMP SNOOPING VTBL
[ 9.328000] [VLAN_MNGR] <06> Creating VLAN VID= 6 Member=0013dfd0 Desc:IGMP SNOOPING VTBL
[ 9.340000] [VLAN_MNGR] <07> Creating VLAN VID= 7 Member=0013ddd0 Desc:IGMP SNOOPING VTBL
[ 9.348000] [VLAN_MNGR] <08> Creating VLAN VID= 8 Member=0013d7d0 Desc:IGMP SNOOPING VTBL
[ 9.360000] [VLAN_MNGR] <09> Creating VLAN VID= 9 Member=0013d5d0 Desc:IGMP SNOOPING VTBL
[ 9.368000] [VLAN_MNGR] <10> Creating VLAN VID= 10 Member=00137fd0 Desc:IGMP SNOOPING VTBL
[ 9.380000] [VLAN_MNGR] <11> Creating VLAN VID= 11 Member=00137dd0 Desc:IGMP SNOOPING VTBL
[ 9.388000] [VLAN_MNGR] <12> Creating VLAN VID= 12 Member=001377d0 Desc:IGMP SNOOPING VTBL
[ 9.396000] [VLAN_MNGR] <13> Creating VLAN VID= 13 Member=001375d0 Desc:IGMP SNOOPING VTBL
[ 9.408000] [VLAN_MNGR] <14> Creating VLAN VID= 14 Member=00135fd0 Desc:IGMP SNOOPING VTBL
[ 9.416000] [VLAN_MNGR] <15> Creating VLAN VID= 15 Member=00135dd0 Desc:IGMP SNOOPING VTBL
[ 9.428000] [VLAN_MNGR] <16> Creating VLAN VID= 16 Member=001357d0 Desc:IGMP SNOOPING VTBL
[ 9.436000] [VLAN_MNGR] <17> Creating VLAN VID= 17 Member=001355d0 Desc:IGMP SNOOPING VTBL
[ 9.448000] athrs17_reg_init:done
[ 9.448000] Setting PHY...
[ 10.456000] napt_ct_scan_thread: time: 4
[ 10.468000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.548000] device eth0.1 entered promiscuous mode
[ 10.552000] device eth0 entered promiscuous mode
[ 10.568000] Now flash open!
[ 10.568000] Read from 0X1FC00 to 0X1FC06: OK
[ 10.576000] isis_ip_intf_entry_add id[0] for vid[1]
[ 10.584000] Lan UDP checksum 0 adding rule #3
[ 10.612000] ACL is not yet enabled. Enabling...
[ 10.620000] isis_ip_intf_entry_add id[1] for vid[2]
[ 10.624000] Wan UDP checksum 0 adding rule #2
[ 10.644000] ttl adding rule #0
[ 10.740000] br0: port 1(eth0.1) entering forwarding state
[ 12.316000] Adding ACL rules 1 - wan to lan, dst ip is lan net
[ 12.952000] nf_conntrack_rtsp v0.6.21 loading
[ 12.956000]
[ 12.956000] Enet:0 port4 up
[ 12.960000] ATH_MAC_TIMER: enet unit:0 is up...
[ 12.968000] RGMii 1000Mbps full duplex
[ 12.972000] ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl
[ 12.976000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.996000] nf_nat_rtsp v0.6.21 loading
[ 13.048000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!
[ 13.348000] asf: module license 'Proprietary' taints kernel.
[ 13.352000] Disabling lock debugging due to kernel taint
[ 13.924000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D )
[ 14.040000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 14.072000] ath_dfs: Version 2.0.0
[ 14.072000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights R eserved
[ 14.412000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
usrconf_allocate_memory 212 shmget success id:43511 32769
[ 15.204000] ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
[ 15.208000] __ath_attach: Set global_scn[0]
[ 15.212000] ACBKMinfree = 48
[ 15.216000] ACBEMinfree = 32
[ 15.216000] ACVIMinfree = 16
[ 15.220000] ACVOMinfree = 0
[ 15.224000] CABMinfree = 48
[ 15.228000] UAPSDMinfree = 0
[ 15.236000] Restoring Cal data from Flash
[ 15.244000] dfs_attach: use DFS enhancements
[ 15.252000] DFS min filter rssiThresh = 18
[ 15.256000] DFS max pulse dur = 151 ticks
[ 15.264000] ath_get_caps[5108] rx chainmask mismatch actual 3 sc_chainmak 0
[ 15.268000] ath_get_caps[5083] tx chainmask mismatch actual 3 sc_chainmak 0
[ 15.284000] SC Callback Registration for wifi0
[ 15.288000] wifi0: Atheros 9340: mem=0xb8100000, irq=2
[ 15.292000] ath_pci: 9.2.0_U10.1020 (Atheros/multi-bss)
[ 15.300000] __ath_attach: Set global_scn[1]
[ 15.304000] ACBKMinfree = 48
[ 15.308000] ACBEMinfree = 32
[ 15.308000] ACVIMinfree = 16
[ 15.312000] ACVOMinfree = 0
[ 15.316000] CABMinfree = 48
[ 15.320000] UAPSDMinfree = 0
[ 15.328000] Restoring Cal data from Flash
[ 15.336000] dfs_attach: use DFS enhancements
[ 15.344000] DFS min filter rssiThresh = 18
[ 15.348000] DFS max pulse dur = 151 ticks
[ 15.352000] ath_get_caps[5108] rx chainmask mismatch actual 7 sc_chainmak 0
[ 15.356000] ath_get_caps[5083] tx chainmask mismatch actual 7 sc_chainmak 0
[ 15.372000] SC Callback Registration for wifi1
[ 15.380000] wifi1: Atheros 9580: mem=0x10000000, irq=64 hw_base=0xb0000000
[ 15.528000] DFS min filter rssiThresh = 15
[ 15.532000] DFS max pulse dur = 151 ticks
[ 15.612000] Now flash open!
[ 15.616000] Read from 0X20000 to 0X20120: OK
[ 15.624000] wlan_vap_create : enter. devhandle=0x86dac2c0, opmode=IEEE80211_M _HOSTAP, flags=0x1
[ 15.636000] wlan_vap_create : exit. devhandle=0x86dac2c0, opmode=IEEE80211_M_ HOSTAP, flags=0x1.
[ 15.644000] VAP device ath0 created
[ 15.808000]
[ 15.808000] DES SSID SET=TP-LINK_2.4GHz_67C93F
[ 15.820000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, vali d=1
[ 21.792000] device ath0 entered promiscuous mode
[ 21.796000] br0: port 2(ath0) entering forwarding state
[ 22.404000] ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, val id=1
[ 22.420000] br0: port 2(ath0) entering disabled state
[ 22.628000]
[ 22.628000] DES SSID SET=TP-LINK_2.4GHz_67C93F
[ 22.656000] br0: port 2(ath0) entering forwarding state
[ 24.520000] br0: port 2(ath0) entering disabled state
[ 24.556000] br0: starting userspace STP failed, starting kernel STP
[ 24.616000] br0: topology change detected, propagating
[ 24.620000] br0: port 2(ath0) entering forwarding state
[ 24.652000] DFS min filter rssiThresh = 15
[ 24.656000] DFS max pulse dur = 151 ticks
[ 24.684000] wlan_vap_create : enter. devhandle=0x86c902c0, opmode=IEEE80211_M _HOSTAP, flags=0x1
[ 24.696000] wlan_vap_create : exit. devhandle=0x86c902c0, opmode=IEEE80211_M_ HOSTAP, flags=0x1.
[ 24.704000] VAP device ath1 created
[ 24.828000]
[ 24.828000] DES SSID SET=TP-LINK_5GHz_67C940
[ 24.844000] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid =1
[ 28.024000] Found best 11na chan: 36
[ 30.720000] br0: port 1(eth0.1) entering disabled state
[ 30.744000] br0: topology change detected, propagating
[ 30.748000] br0: port 1(eth0.1) entering forwarding state
[ 30.772000] device ath1 entered promiscuous mode
[ 30.780000] br0: topology change detected, propagating
[ 30.784000] br0: port 3(ath1) entering forwarding state
[ 30.820000] ieee80211_ioctl_siwmode: imr.ifm_active=852608, new mode=3, vali d=1
[ 30.832000] br0: port 3(ath1) entering disabled state
[ 31.040000]
[ 31.040000] DES SSID SET=TP-LINK_5GHz_67C940
[ 31.064000] br0: topology change detected, propagating
[ 31.068000] br0: port 3(ath1) entering forwarding state
[ 32.840000] br0: port 3(ath1) entering disabled state
[ 32.900000] br0: topology change detected, propagating
[ 32.904000] br0: port 3(ath1) entering forwarding state
[ 33.356000] fuse init (API version 7.12)
[ 33.560000] usbcore: registered new interface driver usbfs
[ 33.564000] usbcore: registered new interface driver hub
[ 33.572000] usbcore: registered new device driver usb
[ 33.604000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 33.652000] Port Status 1c000004
[ 33.656000] ath-ehci ath-ehci.0: ATH EHCI
[ 33.660000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
[ 33.668000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 33.676000] ehci_reset Port Status 1c000000
[ 33.680000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
[ 33.684000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 33.692000] ehci_reset Port Status 1c000000
[ 33.708000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
[ 33.712000] usb usb1: configuration #1 chosen from 1 choice
[ 33.720000] hub 1-0:1.0: USB hub found
[ 33.724000] hub 1-0:1.0: 1 port detected
[ 33.944000] SCSI subsystem initialized
[ 34.076000] usb 1-1: new high speed USB device using ath-ehci and address 2
[ 34.220000] usb 1-1: configuration #1 chosen from 1 choice
[ 34.224000] hub 1-1:1.0: USB hub found
[ 34.232000] hub 1-1:1.0: 4 ports detected
[ 34.292000] Initializing USB Mass Storage driver...
[ 34.296000] usbcore: registered new interface driver usb-storage
[ 34.300000] USB Mass Storage support registered.
[ 36.040000] GPL NetUSB up!
[ 36.264000] kc 88 : run_telnetDBGDServer start
[ 36.272000] kc 225 : init_DebugD end
[ 36.276000] INFO16B9: NetUSB 1.161, 0002061F : Feb 29 2012 15:22:09
[ 36.280000] INFO16BB: AUTH ISOC
[ 36.284000] INFO16BC:
[ 36.288000] usbcore: registered new interface driver KC NetUSB General Driver
[ 36.296000] INFO0076: init proc : PAGE_SIZE 4096
[ 36.300000] INFO1715: Check mac address
[ 36.304000] INFO1575: sleep to wait br0 to wake up
[ 36.312000] INFO02D0: use dev Name br0
[ 36.316000] INFO157E: sleep to wait br0 end.
[ 36.320000] INFO1597: UDP_BROAD 7437 tcpPort:625868800
[ 36.324000] INFO02D0: use dev Name br0
[ 36.328000] my server name : TL-WDR4300
[ 36.332000] INFO14CE: tcpConnector() started...
[ 36.348000] TP_RULE_NAT:enable hardware nat
[ 36.400000] IPv6 over IPv4 tunneling driver
[ 38.908000] (tp_mroute_enable_write)173, tp_mroute_enable = 1
[ 39.360000] INFO13AB: Bind to br0
check success
[ 41.252000] Now flash open!
[ 41.256000] Read from 0X1FC00 to 0X1FC06: OK
[ 41.264000] Now flash open!
[ 41.268000] Read from 0X1FE00 to 0X1FE08: OK
[ 41.272000] Now flash open!
[ 41.276000] Erase from 0X7D0000 to 0X7E21D8:.
[ 41.476000] Program from 0X7D0000 to 0X7E21D8:.
[ 41.852000] write successfully
[ 41.952000] Now flash open!
[ 41.952000] Read from 0X1FE00 to 0X1FE08: OK
[ 41.960000] Now flash open!
[ 41.960000] Erase from 0X7D0000 to 0X7E21D8:.
[ 42.164000] Program from 0X7D0000 to 0X7E21D8:.
[ 42.556000] write successfully
[ 42.560000] Now flash open!
[ 42.564000] Erase from 0X7D0000 to 0X7E21D8:.
[ 42.768000] Program from 0X7D0000 to 0X7E21D8:.
[ 43.144000] write successfully
[ 43.188000] br0: port 2(ath0) entering disabled state
[ 43.208000] br0: port 3(ath1) entering disabled state
[ 44.348000] Restarting system.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 3
Полезный: 0
Решения: 0
Истории: 0
Дата регистрации: 2018-07-15
Re: Восстановление прошивки маршрутизатора
2018-07-15 14:13:21
[quote=igorksm post_id=65956 time=1531648875 user_id=54099] Очень прошу помощи! 4300 v1.7. Ночью роутер "упал", постоянно перезагрузжается. Систему при этом загружает полностью. Я успеваю его увидеть в web. Заметил, что sid wifi сбросился. Пытался его перешить через tftpd. Загрузка файла постоянно разная, может 50% может 88%. Сменил новую флеш. Программатором зашил u-boot, дальше по схеме. tftp+putty. Загрузка 100%. Система стартует, в web успеваю увидеть и... Ребут... Если tftp не закрыть, то будет циклическая загрузка файла после вот этогоПоменял кнопку reset. Была утечка 200 Ом.
First 0x2 last 0x7c sector size 0x10000 124
Erased 123 sectors
Copy to Flash... write addr: 9f020000
done Ребут и по новой загрузка.
Если закрыл прогу, то идет загрузка системы. И последняя команда "restarting system". Куда копать? Получается, что система дает команду рестарта?
Лог putty:
[spoiler=Лог]U-boot DB120 [/quote]
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wdr4300v1_tp_recovery.bin'.
Load address: 0x80060000
Loading: T T ## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting Atheros AR934x
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc v ersion 4.3.3 (GCC) ) #1 Mon Dec 8 14:46:23 CST 2014
[ 0.000000] Ram size passed from bootloader =128M
[ 0.000000] flash_size passed from bootloader = 8
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=s quashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6848k(rootf s),128k(config),64k(ART) mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 112896k/131072k available (1856k kernel code, 17996k rese rved, 432k data, 120k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
[ 0.096000] Mount-cache hash table entries: 512
[ 0.096000]
[ 0.096000] ****************ALLOC***********************
[ 0.096000] Packet mem: 8026e4c0 (0xe00000 bytes)
[ 0.096000] ********************************************
[ 0.096000]
[ 0.096000] NET: Registered protocol family 16
[ 0.096000] PCI init:ath_pcibios_init
[ 0.096000] ath_pcibios_init(294): PCI CMD write: 0x356
[ 0.096000] registering PCI controller with io_map_base unset
[ 0.096000] bio: create slab <bio-0> at 0
[ 0.096000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.096000] pci 0000:00:00.0: PME# disabled
[ 0.096000] Returning IRQ 64
[ 0.100000] NET: Registered protocol family 2
[ 0.100000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.100000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.100000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.100000] TCP reno registered
[ 0.100000] NET: Registered protocol family 1
[ 0.100000] ATH GPIOC major 0
[ 0.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.100000] msgmni has been set to 220
[ 0.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 54)
[ 0.100000] io scheduler noop registered
[ 0.100000] io scheduler deadline registered (default)
[ 0.100000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.104000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.104000] console [ttyS0] enabled
[ 0.404000] PPP generic driver version 2.4.2
[ 0.408000] NET: Registered protocol family 24
[ 0.412000] 5 cmdlinepart partitions found on MTD device ath-nor0
[ 0.416000] Creating 5 MTD partitions on "ath-nor0":
[ 0.424000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.428000] 0x000000020000-0x000000120000 : "kernel"
[ 0.432000] 0x000000120000-0x0000007d0000 : "rootfs"
[ 0.440000] 0x0000007d0000-0x0000007f0000 : "config"
[ 0.444000] 0x0000007f0000-0x000000800000 : "ART"
[ 0.448000] ->Oops: flash id 0xef4017 .
[ 0.452000] ----TP IGMP has been init------
[ 0.456000] TCP cubic registered
[ 0.460000] NET: Registered protocol family 10
[ 0.468000] NET: Registered protocol family 17
[ 0.472000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com >
[ 0.476000] All bugs added by David S. Miller <davem@redhat.com >
[ 0.484000] athwdt_init: Registering WDT success
[ 0.488000] ath_otp_init: Registering OTP success
[ 0.492000] ath_clksw_init: Registering Clock Switch Interface success
[ 0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.516000] Freeing unused kernel memory: 120k freed
init started: BusyBox v1.01 (2014.12.08-06:50+0000) multi-call binary
This Board use 2.6.31
insmod: cannot open module `/lib/modules/2.6.31/kernel/x_tables.ko': No such fil e or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xt_tcpudp.ko': No such fi le or directory
[ 1.684000] xt_time: kernel timezone is -0000
[ 1.884000] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 1.888000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 1.896000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 1.904000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.340000] ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
[ 2.732000] PPPoL2TP kernel driver, V1.0
[ 2.756000] PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
(none) mips #1 Mon Dec 8 14:46:23 CST 2014 (none)
(none) login: [ 5.096000] restoring factory default...
[ 6.992000] Now flash open!
[ 6.996000] Read from 0X20000 to 0X20120: OK
[ 7.524000] Now flash open!
[ 7.528000] Read from 0X7D0000 to 0X7E21D8: OK
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_0=0x00000000
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_1=0x00000000
[ucVlanCfg_init, 92]Prepare paramter :vlanEntry_2=0x00000000
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_3=0x0000 0000
[ucVlanCfg_init, 95]VLAN CFG PARAM STR:vlanEnable=0 vlanEntry_0=0 vlanEntr y_1=0 vlanEntry_2=0 vlanEntry_3=0
[ 8.040000] ATHR_GMAC: Length per segment 1 536
[ 8.044000] ATHR_GMAC: fifo cfg 3 01f00140
[ 8.048000] ATHR_GMAC: RX TASKLET - Pkts per Intr:100
[ 8.052000] ATHR_GMAC: Mac address for unit 0:bfff0000
[ 8.056000] ATHR_GMAC: ff:ff:ff:ff:ff:ff
[ 8.612000] ATHR_GMAC: Max segments per packet : 1
[ 8.616000] ATHR_GMAC: Max tx descriptor count : 128
[ 8.620000] ATHR_GMAC: Max rx descriptor count : 128
[ 8.628000] ATHR_GMAC: Mac capability flags : 2381
[ 8.644000] athr_gmac_ring_alloc Allocated 2048 at 0x87b1f000
[ 8.648000] athr_gmac_ring_alloc Allocated 2048 at 0x87aca800
[ 8.956000] WASP ----> S17 PHY *
[ 8.956000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 8.964000] [VLAN_CONFIG] vlanEnable:Disable
[ 8.968000] [VLAN_CONFIG] Aborting VLAN CONFIG!
[ 9.040000] Hello, nat module!
[ 9.044000] thread: napt_ct_scan create success pid:120
[ 9.048000] netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
[ 9.056000] isis_ip_intf_entry_add id[0] for vid[1]
[ 9.064000] isis_ip_intf_entry_add id[1] for vid[2]
[ 9.068000]
[ 9.068000] ######## S17 SSDK init succeeded! ########
[ 9.080000] [VLAN_MNGR] Registering: VID= 1 Member=001355d0 Policy=0 cookie =000000c8 desc=VLAN 1 For LAN OK
[ 9.092000] [VLAN_MNGR] Registering: VID= 2 Member=001bff50 Policy=0 cookie =000000c8 desc=VLAN 2 For WAN OK
[ 9.104000] ++++ athrs17_igmp_setup once
[ 9.108000] [VLAN_MNGR] Registering: VID= 4 Member=0013fdd0 Policy=3 cookie =87bc1100 desc=IGMP SNOOPING VTBL OK
[ 9.120000] [VLAN_MNGR] Registering: VID= 8 Member=0013f7d0 Policy=3 cookie =87bc1104 desc=IGMP SNOOPING VTBL OK
[ 9.128000] [VLAN_MNGR] Registering: VID= 12 Member=0013f5d0 Policy=3 cookie =87bc1108 desc=IGMP SNOOPING VTBL OK
[ 9.140000] [VLAN_MNGR] Registering: VID= 16 Member=0013dfd0 Policy=3 cookie =87bc110c desc=IGMP SNOOPING VTBL OK
[ 9.152000] [VLAN_MNGR] Registering: VID= 20 Member=0013ddd0 Policy=3 cookie =87bc1110 desc=IGMP SNOOPING VTBL OK
[ 9.160000] [VLAN_MNGR] Registering: VID= 24 Member=0013d7d0 Policy=3 cookie =87bc1114 desc=IGMP SNOOPING VTBL OK
[ 9.172000] [VLAN_MNGR] Registering: VID= 28 Member=0013d5d0 Policy=3 cookie =87bc1118 desc=IGMP SNOOPING VTBL OK
[ 9.180000] [VLAN_MNGR] Registering: VID= 32 Member=00137fd0 Policy=3 cookie =87bc111c desc=IGMP SNOOPING VTBL OK
[ 9.192000] [VLAN_MNGR] Registering: VID= 36 Member=00137dd0 Policy=3 cookie =87bc1120 desc=IGMP SNOOPING VTBL OK
[ 9.204000] [VLAN_MNGR] Registering: VID= 40 Member=001377d0 Policy=3 cookie =87bc1124 desc=IGMP SNOOPING VTBL OK
[ 9.212000] [VLAN_MNGR] Registering: VID= 44 Member=001375d0 Policy=3 cookie =87bc1128 desc=IGMP SNOOPING VTBL OK
[ 9.224000] [VLAN_MNGR] Registering: VID= 48 Member=00135fd0 Policy=3 cookie =87bc112c desc=IGMP SNOOPING VTBL OK
[ 9.236000] [VLAN_MNGR] Registering: VID= 52 Member=00135dd0 Policy=3 cookie =87bc1130 desc=IGMP SNOOPING VTBL OK
[ 9.244000] [VLAN_MNGR] Registering: VID= 56 Member=001357d0 Policy=3 cookie =87bc1134 desc=IGMP SNOOPING VTBL OK
[ 9.256000] [VLAN_MNGR] Registering: VID= 60 Member=001355d0 Policy=3 cookie =87bc1138 desc=IGMP SNOOPING VTBL OK
[ 9.276000] [VLAN_MNGR] <00> Flushing VLAN Table.
[ 9.284000] [VLAN_MNGR] <01> Creating VLAN VID= 1 Member=001355d0 Desc:VLAN 1 For LAN
[ 9.292000] [VLAN_MNGR] <02> Creating VLAN VID= 2 Member=001bff50 Desc:VLAN 2 For WAN
[ 9.300000] [VLAN_MNGR] <03> Creating VLAN VID= 3 Member=0013fdd0 Desc:IGMP SNOOPING VTBL
[ 9.312000] [VLAN_MNGR] <04> Creating VLAN VID= 4 Member=0013f7d0 Desc:IGMP SNOOPING VTBL
[ 9.320000] [VLAN_MNGR] <05> Creating VLAN VID= 5 Member=0013f5d0 Desc:IGMP SNOOPING VTBL
[ 9.328000] [VLAN_MNGR] <06> Creating VLAN VID= 6 Member=0013dfd0 Desc:IGMP SNOOPING VTBL
[ 9.340000] [VLAN_MNGR] <07> Creating VLAN VID= 7 Member=0013ddd0 Desc:IGMP SNOOPING VTBL
[ 9.348000] [VLAN_MNGR] <08> Creating VLAN VID= 8 Member=0013d7d0 Desc:IGMP SNOOPING VTBL
[ 9.360000] [VLAN_MNGR] <09> Creating VLAN VID= 9 Member=0013d5d0 Desc:IGMP SNOOPING VTBL
[ 9.368000] [VLAN_MNGR] <10> Creating VLAN VID= 10 Member=00137fd0 Desc:IGMP SNOOPING VTBL
[ 9.380000] [VLAN_MNGR] <11> Creating VLAN VID= 11 Member=00137dd0 Desc:IGMP SNOOPING VTBL
[ 9.388000] [VLAN_MNGR] <12> Creating VLAN VID= 12 Member=001377d0 Desc:IGMP SNOOPING VTBL
[ 9.396000] [VLAN_MNGR] <13> Creating VLAN VID= 13 Member=001375d0 Desc:IGMP SNOOPING VTBL
[ 9.408000] [VLAN_MNGR] <14> Creating VLAN VID= 14 Member=00135fd0 Desc:IGMP SNOOPING VTBL
[ 9.416000] [VLAN_MNGR] <15> Creating VLAN VID= 15 Member=00135dd0 Desc:IGMP SNOOPING VTBL
[ 9.428000] [VLAN_MNGR] <16> Creating VLAN VID= 16 Member=001357d0 Desc:IGMP SNOOPING VTBL
[ 9.436000] [VLAN_MNGR] <17> Creating VLAN VID= 17 Member=001355d0 Desc:IGMP SNOOPING VTBL
[ 9.448000] athrs17_reg_init:done
[ 9.448000] Setting PHY...
[ 10.456000] napt_ct_scan_thread: time: 4
[ 10.468000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.548000] device eth0.1 entered promiscuous mode
[ 10.552000] device eth0 entered promiscuous mode
[ 10.568000] Now flash open!
[ 10.568000] Read from 0X1FC00 to 0X1FC06: OK
[ 10.576000] isis_ip_intf_entry_add id[0] for vid[1]
[ 10.584000] Lan UDP checksum 0 adding rule #3
[ 10.612000] ACL is not yet enabled. Enabling...
[ 10.620000] isis_ip_intf_entry_add id[1] for vid[2]
[ 10.624000] Wan UDP checksum 0 adding rule #2
[ 10.644000] ttl adding rule #0
[ 10.740000] br0: port 1(eth0.1) entering forwarding state
[ 12.316000] Adding ACL rules 1 - wan to lan, dst ip is lan net
[ 12.952000] nf_conntrack_rtsp v0.6.21 loading
[ 12.956000]
[ 12.956000] Enet:0 port4 up
[ 12.960000] ATH_MAC_TIMER: enet unit:0 is up...
[ 12.968000] RGMii 1000Mbps full duplex
[ 12.972000] ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl
[ 12.976000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.996000] nf_nat_rtsp v0.6.21 loading
[ 13.048000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!
[ 13.348000] asf: module license 'Proprietary' taints kernel.
[ 13.352000] Disabling lock debugging due to kernel taint
[ 13.924000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D )
[ 14.040000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 14.072000] ath_dfs: Version 2.0.0
[ 14.072000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights R eserved
[ 14.412000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
usrconf_allocate_memory 212 shmget success id:43511 32769
[ 15.204000] ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
[ 15.208000] __ath_attach: Set global_scn[0]
[ 15.212000] ACBKMinfree = 48
[ 15.216000] ACBEMinfree = 32
[ 15.216000] ACVIMinfree = 16
[ 15.220000] ACVOMinfree = 0
[ 15.224000] CABMinfree = 48
[ 15.228000] UAPSDMinfree = 0
[ 15.236000] Restoring Cal data from Flash
[ 15.244000] dfs_attach: use DFS enhancements
[ 15.252000] DFS min filter rssiThresh = 18
[ 15.256000] DFS max pulse dur = 151 ticks
[ 15.264000] ath_get_caps[5108] rx chainmask mismatch actual 3 sc_chainmak 0
[ 15.268000] ath_get_caps[5083] tx chainmask mismatch actual 3 sc_chainmak 0
[ 15.284000] SC Callback Registration for wifi0
[ 15.288000] wifi0: Atheros 9340: mem=0xb8100000, irq=2
[ 15.292000] ath_pci: 9.2.0_U10.1020 (Atheros/multi-bss)
[ 15.300000] __ath_attach: Set global_scn[1]
[ 15.304000] ACBKMinfree = 48
[ 15.308000] ACBEMinfree = 32
[ 15.308000] ACVIMinfree = 16
[ 15.312000] ACVOMinfree = 0
[ 15.316000] CABMinfree = 48
[ 15.320000] UAPSDMinfree = 0
[ 15.328000] Restoring Cal data from Flash
[ 15.336000] dfs_attach: use DFS enhancements
[ 15.344000] DFS min filter rssiThresh = 18
[ 15.348000] DFS max pulse dur = 151 ticks
[ 15.352000] ath_get_caps[5108] rx chainmask mismatch actual 7 sc_chainmak 0
[ 15.356000] ath_get_caps[5083] tx chainmask mismatch actual 7 sc_chainmak 0
[ 15.372000] SC Callback Registration for wifi1
[ 15.380000] wifi1: Atheros 9580: mem=0x10000000, irq=64 hw_base=0xb0000000
[ 15.528000] DFS min filter rssiThresh = 15
[ 15.532000] DFS max pulse dur = 151 ticks
[ 15.612000] Now flash open!
[ 15.616000] Read from 0X20000 to 0X20120: OK
[ 15.624000] wlan_vap_create : enter. devhandle=0x86dac2c0, opmode=IEEE80211_M _HOSTAP, flags=0x1
[ 15.636000] wlan_vap_create : exit. devhandle=0x86dac2c0, opmode=IEEE80211_M_ HOSTAP, flags=0x1.
[ 15.644000] VAP device ath0 created
[ 15.808000]
[ 15.808000] DES SSID SET=TP-LINK_2.4GHz_67C93F
[ 15.820000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, vali d=1
[ 21.792000] device ath0 entered promiscuous mode
[ 21.796000] br0: port 2(ath0) entering forwarding state
[ 22.404000] ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, val id=1
[ 22.420000] br0: port 2(ath0) entering disabled state
[ 22.628000]
[ 22.628000] DES SSID SET=TP-LINK_2.4GHz_67C93F
[ 22.656000] br0: port 2(ath0) entering forwarding state
[ 24.520000] br0: port 2(ath0) entering disabled state
[ 24.556000] br0: starting userspace STP failed, starting kernel STP
[ 24.616000] br0: topology change detected, propagating
[ 24.620000] br0: port 2(ath0) entering forwarding state
[ 24.652000] DFS min filter rssiThresh = 15
[ 24.656000] DFS max pulse dur = 151 ticks
[ 24.684000] wlan_vap_create : enter. devhandle=0x86c902c0, opmode=IEEE80211_M _HOSTAP, flags=0x1
[ 24.696000] wlan_vap_create : exit. devhandle=0x86c902c0, opmode=IEEE80211_M_ HOSTAP, flags=0x1.
[ 24.704000] VAP device ath1 created
[ 24.828000]
[ 24.828000] DES SSID SET=TP-LINK_5GHz_67C940
[ 24.844000] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid =1
[ 28.024000] Found best 11na chan: 36
[ 30.720000] br0: port 1(eth0.1) entering disabled state
[ 30.744000] br0: topology change detected, propagating
[ 30.748000] br0: port 1(eth0.1) entering forwarding state
[ 30.772000] device ath1 entered promiscuous mode
[ 30.780000] br0: topology change detected, propagating
[ 30.784000] br0: port 3(ath1) entering forwarding state
[ 30.820000] ieee80211_ioctl_siwmode: imr.ifm_active=852608, new mode=3, vali d=1
[ 30.832000] br0: port 3(ath1) entering disabled state
[ 31.040000]
[ 31.040000] DES SSID SET=TP-LINK_5GHz_67C940
[ 31.064000] br0: topology change detected, propagating
[ 31.068000] br0: port 3(ath1) entering forwarding state
[ 32.840000] br0: port 3(ath1) entering disabled state
[ 32.900000] br0: topology change detected, propagating
[ 32.904000] br0: port 3(ath1) entering forwarding state
[ 33.356000] fuse init (API version 7.12)
[ 33.560000] usbcore: registered new interface driver usbfs
[ 33.564000] usbcore: registered new interface driver hub
[ 33.572000] usbcore: registered new device driver usb
[ 33.604000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 33.652000] Port Status 1c000004
[ 33.656000] ath-ehci ath-ehci.0: ATH EHCI
[ 33.660000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
[ 33.668000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 33.676000] ehci_reset Port Status 1c000000
[ 33.680000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
[ 33.684000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 33.692000] ehci_reset Port Status 1c000000
[ 33.708000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
[ 33.712000] usb usb1: configuration #1 chosen from 1 choice
[ 33.720000] hub 1-0:1.0: USB hub found
[ 33.724000] hub 1-0:1.0: 1 port detected
[ 33.944000] SCSI subsystem initialized
[ 34.076000] usb 1-1: new high speed USB device using ath-ehci and address 2
[ 34.220000] usb 1-1: configuration #1 chosen from 1 choice
[ 34.224000] hub 1-1:1.0: USB hub found
[ 34.232000] hub 1-1:1.0: 4 ports detected
[ 34.292000] Initializing USB Mass Storage driver...
[ 34.296000] usbcore: registered new interface driver usb-storage
[ 34.300000] USB Mass Storage support registered.
[ 36.040000] GPL NetUSB up!
[ 36.264000] kc 88 : run_telnetDBGDServer start
[ 36.272000] kc 225 : init_DebugD end
[ 36.276000] INFO16B9: NetUSB 1.161, 0002061F : Feb 29 2012 15:22:09
[ 36.280000] INFO16BB: AUTH ISOC
[ 36.284000] INFO16BC:
[ 36.288000] usbcore: registered new interface driver KC NetUSB General Driver
[ 36.296000] INFO0076: init proc : PAGE_SIZE 4096
[ 36.300000] INFO1715: Check mac address
[ 36.304000] INFO1575: sleep to wait br0 to wake up
[ 36.312000] INFO02D0: use dev Name br0
[ 36.316000] INFO157E: sleep to wait br0 end.
[ 36.320000] INFO1597: UDP_BROAD 7437 tcpPort:625868800
[ 36.324000] INFO02D0: use dev Name br0
[ 36.328000] my server name : TL-WDR4300
[ 36.332000] INFO14CE: tcpConnector() started...
[ 36.348000] TP_RULE_NAT:enable hardware nat
[ 36.400000] IPv6 over IPv4 tunneling driver
[ 38.908000] (tp_mroute_enable_write)173, tp_mroute_enable = 1
[ 39.360000] INFO13AB: Bind to br0
check success
[ 41.252000] Now flash open!
[ 41.256000] Read from 0X1FC00 to 0X1FC06: OK
[ 41.264000] Now flash open!
[ 41.268000] Read from 0X1FE00 to 0X1FE08: OK
[ 41.272000] Now flash open!
[ 41.276000] Erase from 0X7D0000 to 0X7E21D8:.
[ 41.476000] Program from 0X7D0000 to 0X7E21D8:.
[ 41.852000] write successfully
[ 41.952000] Now flash open!
[ 41.952000] Read from 0X1FE00 to 0X1FE08: OK
[ 41.960000] Now flash open!
[ 41.960000] Erase from 0X7D0000 to 0X7E21D8:.
[ 42.164000] Program from 0X7D0000 to 0X7E21D8:.
[ 42.556000] write successfully
[ 42.560000] Now flash open!
[ 42.564000] Erase from 0X7D0000 to 0X7E21D8:.
[ 42.768000] Program from 0X7D0000 to 0X7E21D8:.
[ 43.144000] write successfully
[ 43.188000] br0: port 2(ath0) entering disabled state
[ 43.208000] br0: port 3(ath1) entering disabled state
[ 44.348000] Restarting system.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 385
Полезный: 13
Решения: 1
Истории: 0
Дата регистрации: 2017-12-08
2018-07-17 07:41:04
Посты: 385
Полезный: 13
Решения: 1
Истории: 0
Дата регистрации: 2017-12-08
Re: Восстановление прошивки маршрутизатора
2018-07-17 07:41:04
[quote=igorksm post_id=65959 time=1531664001 user_id=54099]Проблема решена?[quote=igorksm post_id=65956 time=1531648875 user_id=54099] Очень прошу помощи! 4300 v1.7. Ночью роутер "упал", постоянно перезагрузжается. Систему при этом загружает полностью. Я успеваю его увидеть в web. Заметил, что sid wifi сбросился. Пытался его перешить через tftpd. Загрузка файла постоянно разная, может 50% может 88%. Сменил новую флеш. Программатором зашил u-boot, дальше по схеме. tftp+putty. Загрузка 100%. Система стартует, в web успеваю увидеть и... Ребут... Если tftp не закрыть, то будет циклическая загрузка файла после вот этогоПоменял кнопку reset. Была утечка 200 Ом. [/quote]
First 0x2 last 0x7c sector size 0x10000 124
Erased 123 sectors
Copy to Flash... write addr: 9f020000
done Ребут и по новой загрузка.
Если закрыл прогу, то идет загрузка системы. И последняя команда "restarting system". Куда копать? Получается, что система дает команду рестарта?
Лог putty:
[spoiler=Лог]U-boot DB120 [/quote]
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wdr4300v1_tp_recovery.bin'.
Load address: 0x80060000
Loading: T T ## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting Atheros AR934x
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc v ersion 4.3.3 (GCC) ) #1 Mon Dec 8 14:46:23 CST 2014
[ 0.000000] Ram size passed from bootloader =128M
[ 0.000000] flash_size passed from bootloader = 8
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=s quashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6848k(rootf s),128k(config),64k(ART) mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 112896k/131072k available (1856k kernel code, 17996k rese rved, 432k data, 120k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
[ 0.096000] Mount-cache hash table entries: 512
[ 0.096000]
[ 0.096000] ****************ALLOC***********************
[ 0.096000] Packet mem: 8026e4c0 (0xe00000 bytes)
[ 0.096000] ********************************************
[ 0.096000]
[ 0.096000] NET: Registered protocol family 16
[ 0.096000] PCI init:ath_pcibios_init
[ 0.096000] ath_pcibios_init(294): PCI CMD write: 0x356
[ 0.096000] registering PCI controller with io_map_base unset
[ 0.096000] bio: create slab <bio-0> at 0
[ 0.096000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.096000] pci 0000:00:00.0: PME# disabled
[ 0.096000] Returning IRQ 64
[ 0.100000] NET: Registered protocol family 2
[ 0.100000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.100000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.100000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.100000] TCP reno registered
[ 0.100000] NET: Registered protocol family 1
[ 0.100000] ATH GPIOC major 0
[ 0.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.100000] msgmni has been set to 220
[ 0.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 54)
[ 0.100000] io scheduler noop registered
[ 0.100000] io scheduler deadline registered (default)
[ 0.100000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.104000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.104000] console [ttyS0] enabled
[ 0.404000] PPP generic driver version 2.4.2
[ 0.408000] NET: Registered protocol family 24
[ 0.412000] 5 cmdlinepart partitions found on MTD device ath-nor0
[ 0.416000] Creating 5 MTD partitions on "ath-nor0":
[ 0.424000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.428000] 0x000000020000-0x000000120000 : "kernel"
[ 0.432000] 0x000000120000-0x0000007d0000 : "rootfs"
[ 0.440000] 0x0000007d0000-0x0000007f0000 : "config"
[ 0.444000] 0x0000007f0000-0x000000800000 : "ART"
[ 0.448000] ->Oops: flash id 0xef4017 .
[ 0.452000] ----TP IGMP has been init------
[ 0.456000] TCP cubic registered
[ 0.460000] NET: Registered protocol family 10
[ 0.468000] NET: Registered protocol family 17
[ 0.472000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com >
[ 0.476000] All bugs added by David S. Miller <davem@redhat.com >
[ 0.484000] athwdt_init: Registering WDT success
[ 0.488000] ath_otp_init: Registering OTP success
[ 0.492000] ath_clksw_init: Registering Clock Switch Interface success
[ 0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.516000] Freeing unused kernel memory: 120k freed
init started: BusyBox v1.01 (2014.12.08-06:50+0000) multi-call binary
This Board use 2.6.31
insmod: cannot open module `/lib/modules/2.6.31/kernel/x_tables.ko': No such fil e or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xt_tcpudp.ko': No such fi le or directory
[ 1.684000] xt_time: kernel timezone is -0000
[ 1.884000] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 1.888000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 1.896000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 1.904000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.340000] ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
[ 2.732000] PPPoL2TP kernel driver, V1.0
[ 2.756000] PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
(none) mips #1 Mon Dec 8 14:46:23 CST 2014 (none)
(none) login: [ 5.096000] restoring factory default...
[ 6.992000] Now flash open!
[ 6.996000] Read from 0X20000 to 0X20120: OK
[ 7.524000] Now flash open!
[ 7.528000] Read from 0X7D0000 to 0X7E21D8: OK
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_0=0x00000000
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_1=0x00000000
[ucVlanCfg_init, 92]Prepare paramter :vlanEntry_2=0x00000000
[ucVlanCfg_init, 92]Prepare paramter:vlanEntry_3=0x0000 0000
[ucVlanCfg_init, 95]VLAN CFG PARAM STR:vlanEnable=0 vlanEntry_0=0 vlanEntr y_1=0 vlanEntry_2=0 vlanEntry_3=0
[ 8.040000] ATHR_GMAC: Length per segment 1 536
[ 8.044000] ATHR_GMAC: fifo cfg 3 01f00140
[ 8.048000] ATHR_GMAC: RX TASKLET - Pkts per Intr:100
[ 8.052000] ATHR_GMAC: Mac address for unit 0:bfff0000
[ 8.056000] ATHR_GMAC: ff:ff:ff:ff:ff:ff
[ 8.612000] ATHR_GMAC: Max segments per packet : 1
[ 8.616000] ATHR_GMAC: Max tx descriptor count : 128
[ 8.620000] ATHR_GMAC: Max rx descriptor count : 128
[ 8.628000] ATHR_GMAC: Mac capability flags : 2381
[ 8.644000] athr_gmac_ring_alloc Allocated 2048 at 0x87b1f000
[ 8.648000] athr_gmac_ring_alloc Allocated 2048 at 0x87aca800
[ 8.956000] WASP ----> S17 PHY *
[ 8.956000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 8.964000] [VLAN_CONFIG] vlanEnable:Disable
[ 8.968000] [VLAN_CONFIG] Aborting VLAN CONFIG!
[ 9.040000] Hello, nat module!
[ 9.044000] thread: napt_ct_scan create success pid:120
[ 9.048000] netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
[ 9.056000] isis_ip_intf_entry_add id[0] for vid[1]
[ 9.064000] isis_ip_intf_entry_add id[1] for vid[2]
[ 9.068000]
[ 9.068000] ######## S17 SSDK init succeeded! ########
[ 9.080000] [VLAN_MNGR] Registering: VID= 1 Member=001355d0 Policy=0 cookie =000000c8 desc=VLAN 1 For LAN OK
[ 9.092000] [VLAN_MNGR] Registering: VID= 2 Member=001bff50 Policy=0 cookie =000000c8 desc=VLAN 2 For WAN OK
[ 9.104000] ++++ athrs17_igmp_setup once
[ 9.108000] [VLAN_MNGR] Registering: VID= 4 Member=0013fdd0 Policy=3 cookie =87bc1100 desc=IGMP SNOOPING VTBL OK
[ 9.120000] [VLAN_MNGR] Registering: VID= 8 Member=0013f7d0 Policy=3 cookie =87bc1104 desc=IGMP SNOOPING VTBL OK
[ 9.128000] [VLAN_MNGR] Registering: VID= 12 Member=0013f5d0 Policy=3 cookie =87bc1108 desc=IGMP SNOOPING VTBL OK
[ 9.140000] [VLAN_MNGR] Registering: VID= 16 Member=0013dfd0 Policy=3 cookie =87bc110c desc=IGMP SNOOPING VTBL OK
[ 9.152000] [VLAN_MNGR] Registering: VID= 20 Member=0013ddd0 Policy=3 cookie =87bc1110 desc=IGMP SNOOPING VTBL OK
[ 9.160000] [VLAN_MNGR] Registering: VID= 24 Member=0013d7d0 Policy=3 cookie =87bc1114 desc=IGMP SNOOPING VTBL OK
[ 9.172000] [VLAN_MNGR] Registering: VID= 28 Member=0013d5d0 Policy=3 cookie =87bc1118 desc=IGMP SNOOPING VTBL OK
[ 9.180000] [VLAN_MNGR] Registering: VID= 32 Member=00137fd0 Policy=3 cookie =87bc111c desc=IGMP SNOOPING VTBL OK
[ 9.192000] [VLAN_MNGR] Registering: VID= 36 Member=00137dd0 Policy=3 cookie =87bc1120 desc=IGMP SNOOPING VTBL OK
[ 9.204000] [VLAN_MNGR] Registering: VID= 40 Member=001377d0 Policy=3 cookie =87bc1124 desc=IGMP SNOOPING VTBL OK
[ 9.212000] [VLAN_MNGR] Registering: VID= 44 Member=001375d0 Policy=3 cookie =87bc1128 desc=IGMP SNOOPING VTBL OK
[ 9.224000] [VLAN_MNGR] Registering: VID= 48 Member=00135fd0 Policy=3 cookie =87bc112c desc=IGMP SNOOPING VTBL OK
[ 9.236000] [VLAN_MNGR] Registering: VID= 52 Member=00135dd0 Policy=3 cookie =87bc1130 desc=IGMP SNOOPING VTBL OK
[ 9.244000] [VLAN_MNGR] Registering: VID= 56 Member=001357d0 Policy=3 cookie =87bc1134 desc=IGMP SNOOPING VTBL OK
[ 9.256000] [VLAN_MNGR] Registering: VID= 60 Member=001355d0 Policy=3 cookie =87bc1138 desc=IGMP SNOOPING VTBL OK
[ 9.276000] [VLAN_MNGR] <00> Flushing VLAN Table.
[ 9.284000] [VLAN_MNGR] <01> Creating VLAN VID= 1 Member=001355d0 Desc:VLAN 1 For LAN
[ 9.292000] [VLAN_MNGR] <02> Creating VLAN VID= 2 Member=001bff50 Desc:VLAN 2 For WAN
[ 9.300000] [VLAN_MNGR] <03> Creating VLAN VID= 3 Member=0013fdd0 Desc:IGMP SNOOPING VTBL
[ 9.312000] [VLAN_MNGR] <04> Creating VLAN VID= 4 Member=0013f7d0 Desc:IGMP SNOOPING VTBL
[ 9.320000] [VLAN_MNGR] <05> Creating VLAN VID= 5 Member=0013f5d0 Desc:IGMP SNOOPING VTBL
[ 9.328000] [VLAN_MNGR] <06> Creating VLAN VID= 6 Member=0013dfd0 Desc:IGMP SNOOPING VTBL
[ 9.340000] [VLAN_MNGR] <07> Creating VLAN VID= 7 Member=0013ddd0 Desc:IGMP SNOOPING VTBL
[ 9.348000] [VLAN_MNGR] <08> Creating VLAN VID= 8 Member=0013d7d0 Desc:IGMP SNOOPING VTBL
[ 9.360000] [VLAN_MNGR] <09> Creating VLAN VID= 9 Member=0013d5d0 Desc:IGMP SNOOPING VTBL
[ 9.368000] [VLAN_MNGR] <10> Creating VLAN VID= 10 Member=00137fd0 Desc:IGMP SNOOPING VTBL
[ 9.380000] [VLAN_MNGR] <11> Creating VLAN VID= 11 Member=00137dd0 Desc:IGMP SNOOPING VTBL
[ 9.388000] [VLAN_MNGR] <12> Creating VLAN VID= 12 Member=001377d0 Desc:IGMP SNOOPING VTBL
[ 9.396000] [VLAN_MNGR] <13> Creating VLAN VID= 13 Member=001375d0 Desc:IGMP SNOOPING VTBL
[ 9.408000] [VLAN_MNGR] <14> Creating VLAN VID= 14 Member=00135fd0 Desc:IGMP SNOOPING VTBL
[ 9.416000] [VLAN_MNGR] <15> Creating VLAN VID= 15 Member=00135dd0 Desc:IGMP SNOOPING VTBL
[ 9.428000] [VLAN_MNGR] <16> Creating VLAN VID= 16 Member=001357d0 Desc:IGMP SNOOPING VTBL
[ 9.436000] [VLAN_MNGR] <17> Creating VLAN VID= 17 Member=001355d0 Desc:IGMP SNOOPING VTBL
[ 9.448000] athrs17_reg_init:done
[ 9.448000] Setting PHY...
[ 10.456000] napt_ct_scan_thread: time: 4
[ 10.468000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.548000] device eth0.1 entered promiscuous mode
[ 10.552000] device eth0 entered promiscuous mode
[ 10.568000] Now flash open!
[ 10.568000] Read from 0X1FC00 to 0X1FC06: OK
[ 10.576000] isis_ip_intf_entry_add id[0] for vid[1]
[ 10.584000] Lan UDP checksum 0 adding rule #3
[ 10.612000] ACL is not yet enabled. Enabling...
[ 10.620000] isis_ip_intf_entry_add id[1] for vid[2]
[ 10.624000] Wan UDP checksum 0 adding rule #2
[ 10.644000] ttl adding rule #0
[ 10.740000] br0: port 1(eth0.1) entering forwarding state
[ 12.316000] Adding ACL rules 1 - wan to lan, dst ip is lan net
[ 12.952000] nf_conntrack_rtsp v0.6.21 loading
[ 12.956000]
[ 12.956000] Enet:0 port4 up
[ 12.960000] ATH_MAC_TIMER: enet unit:0 is up...
[ 12.968000] RGMii 1000Mbps full duplex
[ 12.972000] ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl
[ 12.976000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.996000] nf_nat_rtsp v0.6.21 loading
[ 13.048000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!
[ 13.348000] asf: module license 'Proprietary' taints kernel.
[ 13.352000] Disabling lock debugging due to kernel taint
[ 13.924000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D )
[ 14.040000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 14.072000] ath_dfs: Version 2.0.0
[ 14.072000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights R eserved
[ 14.412000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
usrconf_allocate_memory 212 shmget success id:43511 32769
[ 15.204000] ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
[ 15.208000] __ath_attach: Set global_scn[0]
[ 15.212000] ACBKMinfree = 48
[ 15.216000] ACBEMinfree = 32
[ 15.216000] ACVIMinfree = 16
[ 15.220000] ACVOMinfree = 0
[ 15.224000] CABMinfree = 48
[ 15.228000] UAPSDMinfree = 0
[ 15.236000] Restoring Cal data from Flash
[ 15.244000] dfs_attach: use DFS enhancements
[ 15.252000] DFS min filter rssiThresh = 18
[ 15.256000] DFS max pulse dur = 151 ticks
[ 15.264000] ath_get_caps[5108] rx chainmask mismatch actual 3 sc_chainmak 0
[ 15.268000] ath_get_caps[5083] tx chainmask mismatch actual 3 sc_chainmak 0
[ 15.284000] SC Callback Registration for wifi0
[ 15.288000] wifi0: Atheros 9340: mem=0xb8100000, irq=2
[ 15.292000] ath_pci: 9.2.0_U10.1020 (Atheros/multi-bss)
[ 15.300000] __ath_attach: Set global_scn[1]
[ 15.304000] ACBKMinfree = 48
[ 15.308000] ACBEMinfree = 32
[ 15.308000] ACVIMinfree = 16
[ 15.312000] ACVOMinfree = 0
[ 15.316000] CABMinfree = 48
[ 15.320000] UAPSDMinfree = 0
[ 15.328000] Restoring Cal data from Flash
[ 15.336000] dfs_attach: use DFS enhancements
[ 15.344000] DFS min filter rssiThresh = 18
[ 15.348000] DFS max pulse dur = 151 ticks
[ 15.352000] ath_get_caps[5108] rx chainmask mismatch actual 7 sc_chainmak 0
[ 15.356000] ath_get_caps[5083] tx chainmask mismatch actual 7 sc_chainmak 0
[ 15.372000] SC Callback Registration for wifi1
[ 15.380000] wifi1: Atheros 9580: mem=0x10000000, irq=64 hw_base=0xb0000000
[ 15.528000] DFS min filter rssiThresh = 15
[ 15.532000] DFS max pulse dur = 151 ticks
[ 15.612000] Now flash open!
[ 15.616000] Read from 0X20000 to 0X20120: OK
[ 15.624000] wlan_vap_create : enter. devhandle=0x86dac2c0, opmode=IEEE80211_M _HOSTAP, flags=0x1
[ 15.636000] wlan_vap_create : exit. devhandle=0x86dac2c0, opmode=IEEE80211_M_ HOSTAP, flags=0x1.
[ 15.644000] VAP device ath0 created
[ 15.808000]
[ 15.808000] DES SSID SET=TP-LINK_2.4GHz_67C93F
[ 15.820000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, vali d=1
[ 21.792000] device ath0 entered promiscuous mode
[ 21.796000] br0: port 2(ath0) entering forwarding state
[ 22.404000] ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, val id=1
[ 22.420000] br0: port 2(ath0) entering disabled state
[ 22.628000]
[ 22.628000] DES SSID SET=TP-LINK_2.4GHz_67C93F
[ 22.656000] br0: port 2(ath0) entering forwarding state
[ 24.520000] br0: port 2(ath0) entering disabled state
[ 24.556000] br0: starting userspace STP failed, starting kernel STP
[ 24.616000] br0: topology change detected, propagating
[ 24.620000] br0: port 2(ath0) entering forwarding state
[ 24.652000] DFS min filter rssiThresh = 15
[ 24.656000] DFS max pulse dur = 151 ticks
[ 24.684000] wlan_vap_create : enter. devhandle=0x86c902c0, opmode=IEEE80211_M _HOSTAP, flags=0x1
[ 24.696000] wlan_vap_create : exit. devhandle=0x86c902c0, opmode=IEEE80211_M_ HOSTAP, flags=0x1.
[ 24.704000] VAP device ath1 created
[ 24.828000]
[ 24.828000] DES SSID SET=TP-LINK_5GHz_67C940
[ 24.844000] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid =1
[ 28.024000] Found best 11na chan: 36
[ 30.720000] br0: port 1(eth0.1) entering disabled state
[ 30.744000] br0: topology change detected, propagating
[ 30.748000] br0: port 1(eth0.1) entering forwarding state
[ 30.772000] device ath1 entered promiscuous mode
[ 30.780000] br0: topology change detected, propagating
[ 30.784000] br0: port 3(ath1) entering forwarding state
[ 30.820000] ieee80211_ioctl_siwmode: imr.ifm_active=852608, new mode=3, vali d=1
[ 30.832000] br0: port 3(ath1) entering disabled state
[ 31.040000]
[ 31.040000] DES SSID SET=TP-LINK_5GHz_67C940
[ 31.064000] br0: topology change detected, propagating
[ 31.068000] br0: port 3(ath1) entering forwarding state
[ 32.840000] br0: port 3(ath1) entering disabled state
[ 32.900000] br0: topology change detected, propagating
[ 32.904000] br0: port 3(ath1) entering forwarding state
[ 33.356000] fuse init (API version 7.12)
[ 33.560000] usbcore: registered new interface driver usbfs
[ 33.564000] usbcore: registered new interface driver hub
[ 33.572000] usbcore: registered new device driver usb
[ 33.604000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 33.652000] Port Status 1c000004
[ 33.656000] ath-ehci ath-ehci.0: ATH EHCI
[ 33.660000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
[ 33.668000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 33.676000] ehci_reset Port Status 1c000000
[ 33.680000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
[ 33.684000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 33.692000] ehci_reset Port Status 1c000000
[ 33.708000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
[ 33.712000] usb usb1: configuration #1 chosen from 1 choice
[ 33.720000] hub 1-0:1.0: USB hub found
[ 33.724000] hub 1-0:1.0: 1 port detected
[ 33.944000] SCSI subsystem initialized
[ 34.076000] usb 1-1: new high speed USB device using ath-ehci and address 2
[ 34.220000] usb 1-1: configuration #1 chosen from 1 choice
[ 34.224000] hub 1-1:1.0: USB hub found
[ 34.232000] hub 1-1:1.0: 4 ports detected
[ 34.292000] Initializing USB Mass Storage driver...
[ 34.296000] usbcore: registered new interface driver usb-storage
[ 34.300000] USB Mass Storage support registered.
[ 36.040000] GPL NetUSB up!
[ 36.264000] kc 88 : run_telnetDBGDServer start
[ 36.272000] kc 225 : init_DebugD end
[ 36.276000] INFO16B9: NetUSB 1.161, 0002061F : Feb 29 2012 15:22:09
[ 36.280000] INFO16BB: AUTH ISOC
[ 36.284000] INFO16BC:
[ 36.288000] usbcore: registered new interface driver KC NetUSB General Driver
[ 36.296000] INFO0076: init proc : PAGE_SIZE 4096
[ 36.300000] INFO1715: Check mac address
[ 36.304000] INFO1575: sleep to wait br0 to wake up
[ 36.312000] INFO02D0: use dev Name br0
[ 36.316000] INFO157E: sleep to wait br0 end.
[ 36.320000] INFO1597: UDP_BROAD 7437 tcpPort:625868800
[ 36.324000] INFO02D0: use dev Name br0
[ 36.328000] my server name : TL-WDR4300
[ 36.332000] INFO14CE: tcpConnector() started...
[ 36.348000] TP_RULE_NAT:enable hardware nat
[ 36.400000] IPv6 over IPv4 tunneling driver
[ 38.908000] (tp_mroute_enable_write)173, tp_mroute_enable = 1
[ 39.360000] INFO13AB: Bind to br0
check success
[ 41.252000] Now flash open!
[ 41.256000] Read from 0X1FC00 to 0X1FC06: OK
[ 41.264000] Now flash open!
[ 41.268000] Read from 0X1FE00 to 0X1FE08: OK
[ 41.272000] Now flash open!
[ 41.276000] Erase from 0X7D0000 to 0X7E21D8:.
[ 41.476000] Program from 0X7D0000 to 0X7E21D8:.
[ 41.852000] write successfully
[ 41.952000] Now flash open!
[ 41.952000] Read from 0X1FE00 to 0X1FE08: OK
[ 41.960000] Now flash open!
[ 41.960000] Erase from 0X7D0000 to 0X7E21D8:.
[ 42.164000] Program from 0X7D0000 to 0X7E21D8:.
[ 42.556000] write successfully
[ 42.560000] Now flash open!
[ 42.564000] Erase from 0X7D0000 to 0X7E21D8:.
[ 42.768000] Program from 0X7D0000 to 0X7E21D8:.
[ 43.144000] write successfully
[ 43.188000] br0: port 2(ath0) entering disabled state
[ 43.208000] br0: port 3(ath1) entering disabled state
[ 44.348000] Restarting system.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 3
Полезный: 0
Решения: 0
Истории: 0
Дата регистрации: 2018-07-15
Re: Восстановление прошивки маршрутизатора
2018-07-19 16:38:51
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 1
Полезный: 0
Решения: 0
Истории: 0
Дата регистрации: 2018-07-25
Re: Восстановление прошивки маршрутизатора
2018-07-25 13:50:32
Прошу оказать мне техническую помощь в восстановлении роутера wdr4300
Не получалось зайти в админку, сброс параметров к заводским настройкам привел к тому, что вход в админку по-прежнему стал невозможен.
Подключаюсь в браузере по адресу роутера, при этом после указания стандартных логина и пароля в админку я так и не проваливался, крутится колесико, последующая страничка с параметрами не открывается (переход на нее не осуществляется), такое ощущение, что просто не отображается содержимое, пробовал с 4 разных устройств и браузеров, ничего не помогло.
При этом если осуществить попытку такого входа со стационарного компа подсоединенного по сети, то после этого, попытка входа с ноутбука по Wi-Fi отображает ошибку, что в админке уже кто-то работает и в нее возможен только один вход.
Решил залить восстановить прошивку с помощью программки tftp. Все сделал в соответствии с указанными на этом сайте инструкциями.
В результате проблема не решилась. В админку я так и не проваливаюсь.
При этом само устройство работает исправно (в том числе после сброса), при подключении к домашнему провайдеру, интернет раздается по двум диапазонам Wi-Fi, указанным на дне устройства и соответствующими паролями.
Подскажите, что делать в моем случае?
Или уже проще купить новый девайс?
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 1133
Полезный: 40
Решения: 8
Истории: 0
Дата регистрации: 2017-10-16
Re: Восстановление прошивки маршрутизатора
2018-07-27 07:34:21
[quote=Safronien post_id=66176 time=1532526632 user_id=54286] Коллеги, добрый день!
Прошу оказать мне техническую помощь в восстановлении роутера wdr4300
Не получалось зайти в админку, сброс параметров к заводским настройкам привел к тому, что вход в админку по-прежнему стал невозможен.
Подключаюсь в браузере по адресу роутера, при этом после указания стандартных логина и пароля в админку я так и не проваливался, крутится колесико, последующая страничка с параметрами не открывается (переход на нее не осуществляется), такое ощущение, что просто не отображается содержимое, пробовал с 4 разных устройств и браузеров, ничего не помогло.
При этом если осуществить попытку такого входа со стационарного компа подсоединенного по сети, то после этого, попытка входа с ноутбука по Wi-Fi отображает ошибку, что в админке уже кто-то работает и в нее возможен только один вход.
Решил залить восстановить прошивку с помощью программки tftp. Все сделал в соответствии с указанными на этом сайте инструкциями.
В результате проблема не решилась. В админку я так и не проваливаюсь.
При этом само устройство работает исправно (в том числе после сброса), при подключении к домашнему провайдеру, интернет раздается по двум диапазонам Wi-Fi, указанным на дне устройства и соответствующими паролями.
Подскажите, что делать в моем случае?
Или уже проще купить новый девайс? [/quote]
Пробовали войти на роутер в режиме инкогнито? Какой IP получает устройство,на котором работает интернет?
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 6
Полезный: 0
Решения: 0
Истории: 0
Дата регистрации: 2018-06-15
Re: Восстановление прошивки маршрутизатора
2018-08-29 13:27:13
никак не переходит в режим восстановления.
1) держу ресет - и ничего не происходит
2) держу ресет, отпускаю когда загораются два крайних светодиода - и ничего не происходит
провод в первом порту
попробовал на компе и 225 ip и 66 и 60.
но чую он даже в режим не входит. TL_WR842n v5
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 985
Полезный: 5
Решения: 0
Истории: 0
Дата регистрации: 2017-12-08
Re: Восстановление прошивки маршрутизатора
2018-08-29 15:43:51
[quote=PeLeNtRoN post_id=66864 time=1535549233 user_id=53679] что то я туплю.boot удаляли из прошивки?
никак не переходит в режим восстановления.
1) держу ресет - и ничего не происходит
2) держу ресет, отпускаю когда загораются два крайних светодиода - и ничего не происходит
провод в первом порту
попробовал на компе и 225 ip и 66 и 60.
но чую он даже в режим не входит. TL_WR842n v5 [/quote]
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
0
Мы ценим Ваш отзыв. Не стесняйтесь, дайте нам знать больше. Войдите, чтобы отправить отзыв.
#1
Опции
- Копировать ссылку
- Пожаловаться на неуместный контент
Управление потоком
Управление объявлениями
Посты: 992
Полезный: 8
Решения: 0
Истории: 0
Дата регистрации: 2011-05-24
2013-07-22 15:20:48
Посты: 992
Полезный: 8
Решения: 0
Истории: 0
Дата регистрации: 2011-05-24
Информация
Поблагодарили: 0
Просмотры: 104268
Ответы: 63
Избиратели 0
За него еще никто не проголосовал.
Теги
Статьи по теме
Восстановление прошивки.
4735
0
Пожаловаться на неуместный контент
Модуль переноса
Новое сообщение