Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.Tp link 740(KS)-741-Kyivstar перепрошивка -востановление
Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.
Tp link 740(KS)-741-Kyivstar перепрошивка -востановление
Версия прошивки: Ks
Ваша страна: Ua
Название провайдера: Altair
Тип подключения: Pptp
Скорость по тарифу: 100M
Подключение с ПК по wifi или по кабелю?: Wiffi
Если наблюдаются разрывы, то как часто?: редко
Ваша операционная система: Windows7
Антивирусные программы и фаерволы: Msi
После прошивки с киевстаровской на официальную
Через время начала слетать прошивка.
Причина:включение wifi.
Установил open wrt -с отключенным wifi работает.
с родными мак и пин.та же беда.
на 2 роутерах 740такая проблема .другие шились без проблем.
А также на WR-741(rev2.0ks)слетает.
Нужна схема цепи. Может что по питанию wifi. Или не может поставить дрова на wifi
прошивал разными способами -tftp
прошивка полного дампа:
tftp 0x80000000 full.bin
erase 0x9f000000 +0x400000
cp.b 0x80000000 0x9f000000 0x400000
bootm 0x9f020000
====================================
прошивка загрузчика:
uboot：
tftp 0x80000000 uboot.bin
erase 0x9f000000 +0x20000
cp.b 0x80000000 0x9f000000 0x20000
bootm 0x9f020000
====================================
MAC: 0001FC00
KLASS:0001FD00
PIN: 1FE00
==========================
AP91 (ar7240) U-boot
DRAM:
sri
#### TAP VALUE 1 = 8, 2 = 8
32 MB
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment
BOARD IS NOT CALIBRATED!!!
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting AR7240(Python)...
Linux version 2.6.15--LSDK-7.3.0.300 gcc version 3.4.4 #1 Mon May 31 09:58:33 CS T 2010
flash_size passed from bootloader = 4
CPU revision is: 00019374
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashf s init=/sbin/init mtdparts=ar7100-nor0:128k(u-boot),1024k(kernel),2816k(rootfs), 64k(config),64k(art) mem=32M
Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 256 (order: 8, 4096 bytes)
Using 175.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 30532k/32768k available (1382k kernel code, 2220k reserved, 293k data, 1 28k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
Returning IRQ 48
AR7240 GPIOC major 0
squashfs: version 3.3 (2007/10/31) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
HDLC line discipline: version $Revision: #1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 8192K size 1024 blocksize
PPP generic driver version 2.4.2
NET: Registered protocol family 24
cmdlinepart partition parsing not available
Searching for RedBoot partition table
5 RedBoot partitions found on MTD device ar7240-nor0
Creating 5 MTD partitions on "ar7240-nor0":
0x00000000-0x00020000 : "boot"
0x00020000-0x00120000 : "kernel"
0x00120000-0x003e0000 : "rootfs"
0x003e0000-0x003f0000 : "config"
0x003f0000-0x00400000 : "art"
->Oops: flash id 0x10215 .
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <
All bugs added by David S. Miller <
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
init started: BusyBox v1.01 (2010.05.31-02:04+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
ip_conntrack version 2.4 (256 buckets, 5120 max) - 244 bytes per conntrack
insmod: cannot open module `/lib/modules/2.6.15/kernel/flashid.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.15/kernel/harmony.ko': No such file or directory
Now flash open!
Now flash open!
sys_mode=0 mac:81070000 ag7240_macs[0]:00000000 ag7240_macs[1]:81070000
2
sys_mode=0 mac:81c10000 ag7240_macs[0]:81c10000 ag7240_macs[1]:81070000
1
+++ pvid_bitmap initial
(none) mips #1 Mon May 31 09:58:33 CST 2010 (none)
(none) login: sys_mode 0 PHY4 auto-negotiation enable
Attention: PHY4 Class A setting in debug 5 register which is not described in D S
phy_setup ethUnit:0 phyUnit:4
Port 4, Neg Success
++++ phy_up is 1, fdx is 1, speed is 1
ATHRS26: resetting s26
ATHRS26: s26 reset done
sys_mode 0 PHY0 auto-negotiation enable
Attention: PHY 0 Class A setting in debug 5 register which is not described in DS
sys_mode 0 PHY1 auto-negotiation enable
Attention: PHY 1 Class A setting in debug 5 register which is not described in DS
sys_mode 0 PHY2 auto-negotiation enable
Attention: PHY 2 Class A setting in debug 5 register which is not described in DS
sys_mode 0 PHY3 auto-negotiation enable
Attention: PHY 3 Class A setting in debug 5 register which is not described in DS
++++ athrs26_igmp_setup once
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
++ PVID: 0x0000001a, bitmap: 0x0000001f
++ PVID: 0x0000001a, bitmap: 0x0000001f
++ PVID: 0x0000001c, bitmap: 0x0000001f
++ PVID: 0x0000001e, bitmap: 0x0000001f
++ PVID: 0x00000020, bitmap: 0x0000001f
phy_setup ethUnit:1 phyUnit:0
phy_setup ethUnit:1 phyUnit:1
phy_setup ethUnit:1 phyUnit:2
phy_setup ethUnit:1 phyUnit:3
Port 0, Neg Success
Port 1, Neg Success
Port 2, Neg Success
Port 3, Neg Success
device eth0 entered promiscuous mode
phy_setup ethUnit:1 phyUnit:0
phy_setup ethUnit:1 phyUnit:1
phy_setup ethUnit:1 phyUnit:2
phy_setup ethUnit:1 phyUnit:3
Port 0, Neg Success
Port 1, Neg Success
Port 2, Neg Success
Port 3, Neg Success
++++ phy_up is 1, fdx is 1, speed is 1
AG7240: enet unit:0 phy:4 is up...Mii 100Mbps full duplex
AG7240: enet unit 0 phy 4 mode 0x4c04
restoring factory default...
++++ phy_up is 1, fdx is 1, speed is 1
AG7240: enet unit:1 phy:0 is up...Mii 100Mbps full duplex
AG7240: enet unit 1 phy 0 mode 0x4c04
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
+++ GE0 RX DMA ENABLE
Now flash open!
Now flash open!
Now flash open!
Erase from 0X3E0000 to 0X3EC0B4:.
Program from 0X3E0000 to 0X3EC0B4:
write successfully
Now flash open!
Erase from 0X3E0000 to 0X3EC0B4:.
Program from 0X3E0000 to 0X3EC0B4:
write successfully
umount: /var: Device or resource busy
umount: /tmp: Device or resource busy
The system is going down NOW !!
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
Restarting system.
Re: Tp link 740(KS)-741-Kyivstar перепрошивка -востановлен
AP91 (AR7240 - Python 1.2) U-Boot
DRAM: 32 MB
Flash: Spansion S25FL032P (4 MB)
Using default environment
Clocks: CPU:400MHz, DDR:400MHz, AHB:200MHz, Ref:5MHz
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
Fetching MAC Address from 0x9f01fc00
Fetching MAC Address from 0x9f01fc00
GMAC: cfg1 0xf cfg2 0x7114
eth0: f8:d1:11:5c:9c:d2
eth0 up
GMAC: cfg1 0xf cfg2 0x7214
eth1: f8:d1:11:5c:9c:d3
ATHRS26: resetting s26
ATHRS26: s26 reset done
PID hash table entries: 256 (order: 8, 4096 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 30540k/32768k available (1373k kernel code, 2212k reserved, 294k data, 128k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
Reset button pressed.
Returning IRQ 48
AR7240 GPIOC major 0
squashfs: version 3.3 (2007/10/31) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
Serial: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 8192K size 1024 blocksize
PPP generic driver version 2.4.2
PPPoX init, max protocols:3
NET: Registered protocol family 24
pppox protocol 0 register. max:3
cmdlinepart partition parsing not available
Searching for RedBoot partition table
5 RedBoot partitions found on MTD device ar7240-nor0
Creating 5 MTD partitions on "ar7240-nor0":
0x00000000-0x00020000 : "boot"
0x00020000-0x00120000 : "kernel"
0x00120000-0x003e0000 : "rootfs"
0x003e0000-0x003f0000 : "config"
0x003f0000-0x00400000 : "art"
->Oops: flash id 0x10215 .
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <
All bugs added by David S. Miller <
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
init started: BusyBox v1.01 (2010.09.03-04:20+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
This board use 2.6.15
ip_conntrack version 2.4 (256 buckets, 5120 max) - 244 bytes per conntrack
statistics: module license 'BSD' taints kernel.
insmod: cannot open module `/lib/modules/2.6.15/kernel/flashid.ko': No such file or directory
pppox protocol 1 register. max:3
PPPoL2TP kernel driver, V0.17. fixed many bug. drop rcv pkts and xmit pkts while no buffer, use pass time HZ/4.only drop ip pkt. no printk. xl2tpd 15 retries xmit. 08.20
PPTP driver version 0.8.3
pppox protocol 2 register. max:3
insmod: cannot open module `/lib/modules/2.6.15/kernel/harmony.ko': No such file or directory
Now flash open!
Now flash open!
sys_mode=0 mac:8106c000 ag7240_macs[0]:00000000 ag7240_macs[1]:8106c000
2
sys_mode=0 mac:81ca0000 ag7240_macs[0]:81ca0000 ag7240_macs[1]:8106c000
1
+++ pvid_bitmap initial
(none) mips #1 Fri Sep 3 12:31:04 CST 2010 (none)
(none) login: sys_mode 0 PHY4 auto-negotiation enable
Attention: PHY4 Class A setting in debug 5 register which is not described in DS
phy_setup ethUnit:0 phyUnit:4
Port 4, Neg Success
ATHRS26: resetting s26
ATHRS26: s26 reset done
sys_mode 0 PHY0 auto-negotiation enable
Attention: PHY 0 Class A setting in debug 5 register which is not described in DS
sys_mode 0 PHY1 auto-negotiation enable
Attention: PHY 1 Class A setting in debug 5 register which is not described in DS
sys_mode 0 PHY2 auto-negotiation enable
Attention: PHY 2 Class A setting in debug 5 register which is not described in DS
sys_mode 0 PHY3 auto-negotiation enable
Attention: PHY 3 Class A setting in debug 5 register which is not described in DS
++++ athrs26_igmp_setup once
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
++ PVID: 0x0000001a, bitmap: 0x0000001f
++ PVID: 0x0000001a, bitmap: 0x0000001f
++ PVID: 0x0000001c, bitmap: 0x0000001f
++ PVID: 0x0000001e, bitmap: 0x0000001f
++ PVID: 0x00000020, bitmap: 0x0000001f
phy_setup ethUnit:1 phyUnit:0
phy_setup ethUnit:1 phyUnit:1
phy_setup ethUnit:1 phyUnit:2
phy_setup ethUnit:1 phyUnit:3
Port 0, Neg Success
Port 1, Neg Success
Port 2, Neg Success
Port 3, Neg Success
device eth0 entered promiscuous mode
phy_setup ethUnit:1 phyUnit:0
phy_setup ethUnit:1 phyUnit:1
phy_setup ethUnit:1 phyUnit:2
phy_setup ethUnit:1 phyUnit:3
Port 0, Neg Success
Port 1, Neg Success
Port 2, Neg Success
Port 3, Neg Success
++++ phy_up is 1, fdx is 1, speed is 1
AG7240: enet unit:1 phy:0 is up...Mii 100Mbps full duplex
AG7240: enet unit 1 phy 0 mode 0x4c04
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
ath_hal: 0.9.17.1 (AR5416, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
wlan: 0.8.4.2 (Atheros/multi-bss)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 0.9.4.5 (Atheros/multi-bss)
wifi0: Atheros 9285: mem=0x10000000, irq=48 hw_base=0xb0000000
wlan_me: Version 0.1
Copyright (c) 2008 Atheros Communications, Inc. All Rights Reserved
wlan: mac acl policy registered
TP_Flags:6****
ar7240 data bus error: cause 0x80001c
Data bus error, epc == c01712f8, ra == c0171968
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000000 c0171200 801c0000
$ 4 : 81980000 00009860 c01b0000 00009860
$ 8 : 0000096c c0170000 00000000 00000003
$12 : 00000003 00000004 00000003 00000003
$16 : deadc0de 00002710 c01712d0 81980000
$20 : 00009860 c017131c 00000001 00000000
$24 : 00000000 c01720a4
$28 : 81e90000 81e91c28 c0170000 c0171968
Hi : 0000052e
Lo : 1474e400
epc : c01712f8 ath_hal_reg_read+0x28/0x4c [ath_hal] Tainted: P
ra : c0171968 ath_hal_wait+0x7c/0x15c [ath_hal]
Status: 1000f403 KERNEL EXL IE
Cause : 0080001c
PrId : 00019374
Modules linked in: wlan_scan_ap wlan_scan_sta wlan_acl wlan_wep wlan_tkip wlan_ccmp wlan_xauth ath_pktlog wlan_me ath_pci ath_dev ath_rate_atheros wlan ath_hal ip_nat_rtsp ip_conntrack_rtsp ip_nat_h323 ip_nat_tftp ip_conntrack_tftp ip_nat_ftp ip_conntrack_ftp ip_nat_pptp ag7240_mod wlan_warn pptp pppol2tp br_filter ts_kmp cls_fw cls_basic sch_sfq sch_prio sch_htb ipt_MARK ip_conntrack_h323 ipt_multiurl statistics ipt_TCPMSS ip_conntrack_pptp ipt_TRIGGER ipt_time iptable_filter iptable_nat ipt_string ipt_state ipt_multiport ipt_mac ipt_iprange ipt_conntrack ipt_comment ipt_MASQUERADE ip_nat ip_conntrack ip_tables
Process ifconfig (pid: 311, threadinfo=81e90000, task=81c68000)
Stack : c01712ac c01b2dbc 00000000 00009860 00058d21 000000ac 0000000c c0171968
c01782f4 00001124 c017126c 00001070 000001b8 c019ef8c 0000096c 000000a0
c01712ac c0187b0c c01712d0 c017126c 81980000 81980450 c0170000 81971fb4
81980450 00000006 81e91d18 c019290c c01712ac 81980450 81980450 c01b2d00
000186a0 00004014 28080400 00004014 00000000 00000000 00000000 c017a2b4
...
Call Trace:
[<c01712ac>] ath_hal_reg_write+0x40/0x64 [ath_hal]
[<c0171968>] ath_hal_wait+0x7c/0x15c [ath_hal]
[<c01782f4>] ath_hal_checkchannel+0x74/0x20c [ath_hal]
[<c017126c>] ath_hal_reg_write+0x0/0x64 [ath_hal]
[<c01712ac>] ath_hal_reg_write+0x40/0x64 [ath_hal]
[<c0187b0c>] ar5416SetSlotTime+0xb8/0xd8 [ath_hal]
[<c01712d0>] ath_hal_reg_read+0x0/0x4c [ath_hal]
[<c017126c>] ath_hal_reg_write+0x0/0x64 [ath_hal]
[<c019290c>] ar5416Reset+0xa34/0x18dc [ath_hal]
[<c01712ac>] ath_hal_reg_write+0x40/0x64 [ath_hal]
[<c017a2b4>] ar5416ConfigPciPowerSave+0x198/0x340 [ath_hal]
[<c020fd28>] ath_open+0xf0/0x344 [ath_dev]
[<c01457ec>] ath_chan2flags+0x1c/0x68 [ath_pci]
[<80006954>] do_IRQ+0x24/0x34
[<c01458bc>] ath_init+0x54/0x118 [ath_pci]
[<80008400>] _sys_sigreturn+0x51c/0x660
[<800f7380>] dev_open+0x64/0xd8
[<c01e0e68>] ieee80211_init+0x168/0x1d4 [wlan]
[<800f7380>] dev_open+0x64/0xd8
[<800f8af4>] dev_change_flags+0x74/0x14c
[<800f7260>] dev_load+0x10/0x44
[<8013d300>] devinet_ioctl+0x318/0x778
[<8013d16c>] devinet_ioctl+0x184/0x778
[<8013e91c>] inet_ioctl+0xd8/0x130
[<8007949c>] d_alloc+0x34/0x1a4
[<800ed224>] sock_ioctl+0x318/0x344
[<800b8194>] sprintf+0x28/0x34
[<8005856c>] split_vma+0x148/0x16c
[<80073170>] do_ioctl+0x30/0x78
[<800734ec>] vfs_ioctl+0x334/0x35c
[<800ed77c>] sock_create+0x10/0x1c
[<80073564>] sys_ioctl+0x50/0x8c
[<8000e240>] stack_done+0x20/0x3c
[<8000e240>] stack_done+0x20/0x3c
Code: 8c500000 3c02c017 24421200 <afb00010> 24c63298 0040f809 24050004 02001021 8fbf001c
