TL-WR740N(RU) Ver.4.25 при прошивке окирпичился
Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.
TL-WR740N(RU) Ver.4.25 при прошивке окирпичился
Версия прошивки: 140814
Ваша страна: Россия
Здравствуйте, поставил OpenWRT, все работало нормально, но потом начались проблемы с зависанием онлайн видео на всех сайтах, при этом скорость подключения 90Mbps судя по тестам и данным тарифа.
Решил сменить прошивку на родную, делал по инструкции http://forum.tp-linkru.ru/viewtopic.php?f=68&t=2542
В тексте инструкции сказано что если в названии прошивки нет слова boot то надо пропустить 257 блоков этой прошивки командой dd
В официальной же прошивке нет слова boot поэтому я делать этого не стал ( качал версию TL-WR740N_V4_140814_RU)
При прошивке появилась ошибка вида Writing from /tmp/tplink.bin to firmware ... [e]Failed to erase block
Что означает что boot все же был в прошивке, но не указан в названии прошивки
После этого, при попытке прошить все же без boot появлялась ошибка Bus error
Далее попробовал перезагрузить устройство
Сейчас, судя по лампочкам, устройство непрерывно перезагружается (включаю, горят все лампочки, потом гаснут, потом опять горят и до бесконечности)
Подскажите, можно ли как то раскирпичить аппарат? Способ с TFTP не помогает, Wireshark не видит пакеты в подсети 192.168.0.0/24 и 192.168.1.0/24
Re: TL-WR740N(RU) Ver.4.25 при прошивке окирпичился
С этой штукой роутер прошился без проблем
Однако сейчас не могу завести wifi, ставлю ту же самую прошивку openwrt что стояла до того как я его окирпичил. Пробовал и sysupgrade и factory, никакого толку.
Вот вывод dmesg:
[ 0.000000] MyLoader: sysp=9d2c0f5b, boardp=5b365f3e, parts=3e39e2b4
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 8034e2b0, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28516K/32768K available (2621K kernel code, 129K rwdata, 344K rodata, 224K init, 194K bss, 4252K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[ 0.560000] Switched to clocksource MIPS
[ 0.560000] NET: Registered protocol family 2
[ 0.570000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.580000] TCP: reno registered
[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.600000] PCI: CLS 0 bytes, default 32
[ 0.600000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.630000] msgmni has been set to 55
[ 0.630000] io scheduler noop registered
[ 0.640000] io scheduler deadline registered (default)
[ 0.640000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a AR933X UART
[ 0.660000] console [ttyATH0] enabled
[ 0.670000] bootconsole [early0] disabled
[ 0.680000] m25p80 spi0.0: found s25sl032p, expected m25p80
[ 0.680000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
[ 0.690000] 5 tp-link partitions found on MTD device spi0.0
[ 0.690000] Creating 5 MTD partitions on "spi0.0":
[ 0.700000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.700000] 0x000000020000-0x00000012c510 : "kernel"
[ 0.710000] 0x00000012c510-0x0000003f0000 : "rootfs"
[ 0.710000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.720000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.720000] 0x000000350000-0x0000003f0000 : "rootfs_data"
[ 0.730000] 0x0000003f0000-0x000000400000 : "art"
[ 0.730000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.770000] libphy: ag71xx_mdio: probed
[ 1.370000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
[ 1.400000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 1.990000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 2.000000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.000000] TCP: cubic registered
[ 2.000000] NET: Registered protocol family 17
[ 2.010000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.020000] Bridge firewalling registered
[ 2.030000] 8021q: 802.1Q VLAN Support v1.8
[ 2.040000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.050000] Freeing unused kernel memory: 224K (80368000 - 803a0000)
[ 3.350000] init: Console is alive
[ 3.350000] init: - watchdog -
[ 5.430000] init: - preinit -
[ 6.270000] random: procd urandom read with 9 bits of entropy available
[ 7.840000] eth0: link up (1000Mbps/Full duplex)
[ 9.680000] jffs2: notice: (346) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.700000] mount_root: switching to jffs2 overlay
[ 9.750000] eth0: link down
[ 9.770000] procd: - early -
[ 9.770000] procd: - watchdog -
[ 10.440000] procd: - ubus -
[ 11.450000] procd: - init -
[ 12.370000] NET: Registered protocol family 10
[ 12.380000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.400000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 12.410000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 12.420000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.430000] nf_conntrack version 0.5.0 (449 buckets, 1796 max)
[ 12.480000] xt_time: kernel timezone is -0000
[ 12.510000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.540000] cfg80211: World regulatory domain updated:
[ 12.540000] cfg80211: DFS Master region: unset
[ 12.540000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.550000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.560000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.570000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.580000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.590000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 12.600000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 12.600000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.610000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 12.670000] PPP generic driver version 2.4.2
[ 12.680000] NET: Registered protocol family 24
[ 12.760000] ath: phy0: Unable to initialize hardware; initialization status: -5
[ 12.770000] ath9k ar933x_wmac: failed to initialize device
[ 12.770000] ath9k: probe of ar933x_wmac failed with error -5
[ 23.370000] device eth0 entered promiscuous mode
[ 23.400000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 23.430000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 24.970000] eth0: link up (1000Mbps/Full duplex)
[ 24.970000] br-lan: port 1(eth0) entered forwarding state
[ 24.980000] br-lan: port 1(eth0) entered forwarding state
[ 24.980000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 25.560000] eth1: link up (100Mbps/Full duplex)
[ 25.560000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 26.980000] br-lan: port 1(eth0) entered forwarding state
[ 31.120000] pppoe-wan: renamed from ppp0
[ 70.060000] random: nonblocking pool is initialized
Скриншот интерфейса Luci (отсутствует пункт wifi):
