Archer C7 v2 невозможно подключиться

Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.

Archer C7 v2 невозможно подключиться

Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.
Archer C7 v2 невозможно подключиться
Archer C7 v2 невозможно подключиться
2018-09-02 22:18:43
:cry: Здравствуйте.
Есть роутер Archer C7 v2, ранее на роутере стояла прошивка OpenWrt. После 2-х недельного отсутствия приехав домой обнаружил, что все устройства подключенные к LAN недоступны. При назначении статического IP устройства включенные в LAN-порты роутера видят друг-друга... Подумал проблема с прошивкой, решил откатится на родную.
По tftp не получилось прошить, нет передачи данных, при этом горит линк на портах, и на роутере и на ноутбуке. Для прошивки использую tftpd32, на ноуте IP 192.168.0.66
Скажу сразу, что на аналогичном роутере Archer C7 v4 получается перепрошиться, так что проблема не в файерволе, антиврусе и т.п.

В итоге после безуспешных попыток, зашел по WiFi и через web-интерфейс openWrt прошил стоковую прошивку (без boot). И... получил недоступность и по wiFi вдобавок.
Распаял UART, лог загрузки ниже под катом.
Похоже грузится штатно, видно в режиме восстановления ожидает ArcherC7v2_tp_recovery.bin но на tftpd никаких запросов не фиксируется...
Теперь осталась возможность залогиниться в BusyBox по UART и раскирпичить роутер... Но как ?
В ответ на посылку логина: [quote] Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: Admin
login: no valid shadow password

Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: admin
Password:
Login incorrect[/quote]
U-Boot 1.1.4 (Feb 9 2017 - 11:51:45)

ap135 - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(179): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x3, 0x1f)
Tap values = (0x11, 0x11, 0x11, 0x11)
128 MB
Flash Manuf Id 0x1, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment

*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ----> S17 PHY *
Vlan config...
TEST: FINAL REG VAL after TX Calibration - 0x46000000
TEST: FINAL XMII VAL after RX Calibration - 0x46000000
TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00000001
athrs17_reg_init: complete
: cfg1 0x80000000 cfg2 0x7335
eth0: ba:be:fa:ce:08:41
eth0 up
athrs17_reg_init_wan done
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
eth1 up
eth0, eth1
Setting 0x18116290 to 0x58b1214f
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'ArcherC7v2_tp_recovery.bin'.
Load address: 0x80060000
Loading: T T ## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK

Starting kernel ...

Booting QCA955x<0>
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc version 4.3.3 (GCC) ) #1 Thu Mar 8 10:14:28 CST 2018
[ 0.000000] Ram size passed from bootloader =128M
[ 0.000000] flash_size passed from bootloader = 16
[ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[ 0.000000] cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 619 ahb 206
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),14848k(rootfs),320k(config),64k(ART) mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 112924k/131072k available (1844k kernel code, 17980k reserved, 429k data, 120k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
[ 0.080000] Mount-cache hash table entries: 512
[ 0.080000]
[ 0.080000] ****************ALLOC***********************
[ 0.080000] Packet mem: 8026a4e0 (0xe00000 bytes)
[ 0.080000] ********************************************
[ 0.080000]
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] ath_pcibios_init: bus 0
[ 0.080000] ***** Warning PCIe 0 H/W not found !!!
[ 0.080000] registering PCI controller with io_map_base unset
[ 0.080000] ath_pcibios_init: bus 1
[ 0.080000] ath_pcibios_init(232): PCI 1 CMD write: 0x356
[ 0.080000] registering PCI controller with io_map_base unset
[ 0.080000] ===@@@@@@@@@@@=>use GPIO23 as wifi button control!
[ 0.080000] bio: create slab <bio-0> at 0
[ 0.084000] pcibios_map_irq: IRQ 76 for bus 1
[ 0.084000] NET: Registered protocol family 2
[ 0.084000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.084000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.084000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.084000] TCP reno registered
[ 0.084000] NET: Registered protocol family 1
[ 0.084000] ATH GPIOC major 0
[ 0.084000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.084000] msgmni has been set to 220
[ 0.088000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.088000] io scheduler noop registered
[ 0.088000] io scheduler deadline registered (default)
[ 0.088000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.088000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.088000] console [ttyS0] enabled
[ 0.396000] PPP generic driver version 2.4.2
[ 0.400000] NET: Registered protocol family 24
[ 0.404000] 5 cmdlinepart partitions found on MTD device ath-nor0
[ 0.412000] Creating 5 MTD partitions on "ath-nor0":
[ 0.416000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.420000] 0x000000020000-0x000000120000 : "kernel"
[ 0.428000] 0x000000120000-0x000000fa0000 : "rootfs"
[ 0.432000] 0x000000fa0000-0x000000ff0000 : "config"
[ 0.436000] 0x000000ff0000-0x000001000000 : "ART"
[ 0.444000] ->Oops: flash id 0x12018 .
[ 0.448000] Ooops, why the devices couldn't been initialed?
[ 0.452000] TCP cubic registered
[ 0.456000] NET: Registered protocol family 10
[ 0.460000] NET: Registered protocol family 17
[ 0.464000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.472000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.480000] athwdt_init: Registering WDT success
[ 0.484000] ath_otp_init: Registering OTP success
[ 0.496000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.504000] Freeing unused kernel memory: 120k freed

init started: BusyBox v1.01 (2015.09.28-09:17+0000) multi-call binary
This Board use 2.6.31
[ 2.164000] xt_time: kernel timezone is -0000
[ 2.364000] nf_conntrack version 0.5.0 (2048 buckets, 81920 max)
[ 2.372000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 2.380000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 2.388000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.876000] ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/igmp_agent.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
[ 3.384000] PPPoL2TP kernel driver, V1.0
[ 3.404000] PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory

(none) mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
(none) login: [ 7.968000] Read from 0X20000 to 0X2014C: OK
[ 8.068000] Read from 0XFA0000 to 0XFB2ED4: OK
[ucVlanCfg_init, 175]Prepare paramter:vlanEntry_0=0x00000000[ucVlanCfg_init, 175]Prepare paramter:vlanEntry_1=0x00000000[ucVlanCfg_init, 175]Prepare paramter:vlanEntry_2=0x00000000[ucVlanCfg_init, 175]Prepare paramter:vlanEntry_3=0x00000000[ucVlanCfg_init, 178]VLAN CFG PARAM STR:vlanEnable=0 vlanEntry_0=0 vlanEntry_1=0 vlanEntry_2=0 vlanEntry_3=0 ====>>>>vid_offset is 0
====>>>>lan:eth0[ 8.480000] Read from 0X1FC00 to 0X1FC06:.1
OK
[ 8.912000] qca955x_GMAC: Length per segment 1536
[ 8.916000] 955x_GMAC: qca955x_gmac_attach
[ 8.920000] 955x_GMAC: qca955x_set_gmac_caps
[ 8.924000] Currently in polling mode unit1
[ 8.928000] mac:1 Registering S17....
[ 8.932000] qca955x_GMAC: RX TASKLET - Pkts per Intr:200
[ 8.940000] qca955x_GMAC: Max segments per packet : 1
[ 8.944000] qca955x_GMAC: Max tx descriptor count : 220
[ 8.948000] qca955x_GMAC: Max rx descriptor count : 220
[ 8.956000] qca955x_GMAC: Mac capability flags : 12002200
[ 8.960000] 955x_GMAC: qca955x_gmac_attach
[ 8.964000] 955x_GMAC: qca955x_set_gmac_caps
[ 8.968000] Currently in polling mode unit0
[ 8.972000] mac:0 Registering S17....
[ 8.976000] qca955x_GMAC: RX TASKLET - Pkts per Intr:200
[ 8.984000] qca955x_GMAC: Max segments per packet : 1
[ 8.988000] qca955x_GMAC: Max tx descriptor count : 220
[ 8.992000] qca955x_GMAC: Max rx descriptor count : 220
[ 9.000000] qca955x_GMAC: Mac capability flags : 10002A00
[ 9.004000] 955x_GMAC: Serdes PLL is locked value 0x1f038516
[ 9.640000] athr_gmac_ring_alloc Allocated 3520 at 0x8794d000
[ 9.648000] athr_gmac_ring_alloc Allocated 3520 at 0x87b29000
[ 9.952000] 955x_GMAC: eth1 in SGMII MODE
[ 9.956000] Scorpion -----> S17 PHY
[ 9.988000] Hello, nat helper module for 1.08!
[ 9.992000] netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
[ 10.000000]
[ 10.000010.420000] [VLAN_MNGR] <07> Creating VLAN VID= 7 Member=0013ddd0 Desc:IGMP Snooping
[ 10.428000] [VLAN_MNGR] <08> Creating VLAN VID= 8 Member=0013d7d0 Desc:IGMP Snoopi1175d0 Desc:IGMP Snooping
[ 10.608000] [VLAN_MNGR] <30> Creating VLAN VID= 30 Member=00115fd0 Desc:IGMP Snooping
[ 10.616000] [VLAN_MNGR] <31> Creating VLAN VID= 31 Member=00115dd0 Desc:IGMP Snooping
[ 10.624000] [VLAN_MNGR] <32> Creating VLAN VID= 32 Member=001157d0 Desc:IGMP Snooping
[ 10.632000] [VLAN_MNGR] <33> Creating VLAN VID= 33 Member=001155d0 Desc:IGMP Snooping
[ 10.640000] [VLAN_MNGR] <34> Creating VLAN VID= 34 Member=0011ffe0 Desc:Guest VLAN
[ 10.652000] athrs17_reg_init:done
[ 10.652000] 955x_SGMII::athr_gmac_sgmii_setup Done
[ 10.660000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 10.664000] Setting PHY...
[ 10.668000] vid_offset is 0
1 Member=00115dd0 Desc:IGMP Snooping
[ 10.624000] [VLAN_MNGR] <32> Creating VLAN VID= 32 Member=001157d0 Desc:IGMP Snooping
[ 10.632000] [VLAN_MNGR] <33> Creating VLAN VID= 33 Member=001155d0 Desc:IGMP Snooping
[ 10.640000] [VLAN_MNGR] <34> Creating VLAN VID= 34 Member=0011ffe0 Desc:Guest VLAN
[ 10.652000] athrs17_reg_init:done
[ 10.652000] 955x_SGMII::athr_gmac_sgmii_setup Done
[ 10.660000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 10.664000] Setting PHY...
[ 10.668000] vid_offset is 0
ooping
[ 10.484000] [VLAN_MNGR] <15> Creating VLAN VID= 15 Member=00135dd0 Desc:IGMP Snooping
[ 10.492000] [VLAN_MNGR] <16> Creating VLAN VID= 16 Member=001357d0 Desc:IGMP Snooping
[ 10.504000] [VLAN_MNGR] <17> Creating VLAN VID= 17 Member=001355d0 Desc:IGMP Snooping
[ 10.512000] [VLAN_MNGR] <18> Creating VLAN VID= 18 Member=0011ffd0 Desc:IGMP Snooping
[ 10.520000] [VLAN_MNGR] <19> Creating VLAN VID= 19 Member=0011fdd0 Desc:IGMP Snooping
[ 10.528000] [VLAN_MNGR] <20> Creating VLAN VID= 20 Member=0011f7d0 Desc:IGMP Snooping
[ 10.536000] [VLAN_MNGR] <21> Creating VLAN VID= 21 Member=0011f5d0 Desc:IGMP Snooping
[ 10.544000] [VLAN_MNGR] <22> Creating VLAN VID= 22 Member=0011dfd0 Desc:IGMP Snooping
[ 10.552000] [VLAN_MNGR] <23> Creating VLAN VID= 23 Member=0011ddd0 Desc:IGMP Snooping
[ 10.560000] [VLAN_MNGR] <24> Creating VLAN VID= 24 Member=0011d7d0 Desc:IGMP Snooping
[ 10.568000] [VLAN_MNGR] <25> Creating VLAN VID= 25 Member=0011d5d0 Desc:IGMP Snooping
[ 10.576000] [VLAN_MNGR] <26> Creating VLAN VID= 26 Member=00117fd0 Desc:IGMP Snooping
[ 10.584000] [VLAN_MNGR] <27> Creating VLAN VID= 27 Member=00117dd0 Desc:IGMP Snooping
[ 10.592000] [VLAN_MNGR] <28> Creating VLAN VID= 28 Member=001177d0 Desc:IGMP Snooping
[ 10.600000] [VLAN_MNGR] <29> Creating VLAN VID= 29 Member=00[ 11.672000] Phy setup Complete
[ 11.684000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.760000] device eth0.1 entered promiscuous mode
[ 11.776000] Read from 0X1FC00 to 0X1FC06: OK
[ 11.780000] SET INTF MAC 0:14-cc-20-5c-bf-3a
[ 11.788000] Lan UDP checksum 0 adding rule #3
[ 11.796000] ACL is not yet enabled. Enabling...
[ 11.800000] SET INTF MAC 1:14-cc-20-5c-bf-3b
[ 11.804000] ttl adding rule #0
[ 11.808000] Wan UDP checksum 0 adding rule #2
[ 11.844000] device eth0 entered promiscuous mode
[ 11.908000] br0: port 1(eth0.1) entering forwarding state
[ 13.812000] Adding ACL rules #1 - wan to lan, dst ip is lan net
[ 14.388000] nf_conntrack_rtsp v0.6.21 loading
[ 14.408000] nf_nat_rtsp v0.6.21 loading
[ 14.464000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

====>>>>init2G...right region RU,cur region:83
[ 14.692000] adf: module license 'Proprietary' taints kernel.
[ 14.700000] Disabling lock debugging due to kernel taint
[ 13.812000] Adding ACL rules #1 - wan to lan, dst ip is lan net
[ 14.388000] nf_conntrack_rtsp v0.6.21 loading
[ 14.408000] nf_nat_rtsp v0.6.21 loading
[ 14.464000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

====>>>>init2G...right region RU,cur region:83
[ 14.692000] adf: module license 'Proprietary' taints kernel.
[ 14.700000] Disabling lock debugging due to kernel taint
11.808000] Wan UDP checksum 0 adding rule #2
[ 11.844000] device eth0 entered promiscuous mode
[ 11.908000] br0: port 1(eth0.1) entering forwarding state
N VID= 15 Member=00135dd0 Desc:IGMP Snooping
[ 10.492000] [VLAN_MNGR] <16> Creating VLAN VID= 16 Member=001357d0 Desc:IGMP Snooping
[ 10.504000] [VLAN_MNGR] <17> Creating VLAN VID= 17 Member=001355d0 Desc:IGMP Snooping
[ 10.512000] [VLAN_MNGR] <18> Creating VLAN VID= 18 Member=0011ffd0 Desc:IGMP Snooping
[ 10.520000] [VLAN_MNGR] <19> Creating VLAN VID= 19 Member=0011fdd0 Desc:IGMP Snooping
[ 10.528000] [VLAN_MNGR] <20> Creating VLAN VID= 20 Member=0011f7d0 Desc:IGMP Snooping
[ 10.536000] [VLAN_MNGR] <21> Creating VLAN VID= 21 Member=0011f5d0 Desc:IGMP Snooping
[ 10.544000] [VLAN_MNGR] <22> Creating VLAN VID= 22 Member=0011dfd0 Desc:IGMP Snooping
[ 10.552000] [VLAN_MNGR] <23> Creating VLAN VID= 23 Member=0011ddd0 Desc:IGMP Snooping
[ 10.560000] [VLAN_MNGR] <24> Creating VLAN VID= 24 Member=0011d7d0 Desc:IGMP Snooping
[ 10.568000] [VLAN_MNGR] <25> Creating VLAN VID= 25 Member=0011d5d0 Desc:IGMP Snooping
[ 10.576000] [VLAN_MNGR] <26> Creating VLAN VID= 26 Member=00117fd0 Desc:IGMP Snooping
[ 10.584000] [VLAN_MNGR] <27> Creating VLAN VID= 27 Member=00117dd0 Desc:IGMP Snooping
[ 10.592000] [VLAN_MNGR] <28> Creating VLAN VID= 28 Member=001177d0 Desc:IGMP Snooping
[ 10.600000] [VLAN_MNGR] <29> Creating VLAN VID= 29 Member=00 OK
[ 10.172000] [VLAN_MNGR] Registering: VID= 0 Member=001357d0 Policy=3 cookie=87bcb6f8 desc=IGMP Snooping OK
[ 10.180000] [VLAN_MNGR] Registering: VID= 0 Member=001355d0 Policy=3 cookie=87bcb6fc desc=IGMP Snooping OK
[ 10.192000] [VLAN_MNGR] Registering: VID= 0 Member=0011ffd0 Policy=3 cookie=87bcb700 desc=IGMP Snooping OK
[ 10.200000] [VLAN_MNGR] Registering: VID= 0 Member=0011fdd0 Policy=3 cookie=87bcb704 desc=IGMP Snooping OK
[ 10.212000] [VLAN_MNGR] Registering: VID= 0 Member=0011f7d0 Policy=3 cookie=87bcb708 desc=IGMP Snooping OK
[ 10.220000] [VLAN_MNGR] Registering: VID= 0 Member=0011f5d0 Policy=3 cookie=87bcb70c desc=IGMP Snooping OK
[ 10.232000] [VLAN_MNGR] Registering: VID= 0 Member=0011dfd0 Policy=3 cookie=87bcb710 desc=IGMP Snooping OK
[ 10.240000] [VLAN_MNGR] Registering: VID= 0 Member=0011ddd0 Policy=3 cookie=87bcb714 desc=IGMP Snooping OK
[ 10.252000] [VLAN_MNGR] Registering: VID= 0 Member=0011d7d0 Policy=3 cookie=87bcb718 desc=IGMP Snooping OK
[ 10.260000] [VLAN_MNGR] Registering: VID= 0 Member=0011d5d0 Policy=3 cookie=87bcb71c desc=IGMP Snooping OK
[ 10.272000] [VLAN_MNGR] Registering: VID= 0 Member=00117fd0 Policy=3 cookie=87bcb720 desc=IGMP Snooping OK
[ 10.280000] [VLAN_MNGR] Registering: VID= 0 Member=00117dd0 Policy=3 cookie=87bcb724 desc=IGMP Snooping OK
[ 10.292000] [VLAN_MNGR] Registering: VID= 0 Member=001177d0 Policy=3 cookie=87bcb728 desc=IGMP Snooping OK
[ 10.300000] [VLAN_MNGR] Registering: VID= 0 Member=001175d0 Policy=3 cookie=87bcb72c desc=IGMP Snooping OK
[ 10.312000] [VLAN_MNGR] Registering: VID= 0 Member=00115fd0 Policy=3 cookie=87bcb730 desc=IGMP Snooping OK
[ 10.320000] [VLAN_MNGR] Registering: VID= 0 Member=00115dd0 Policy=3 cookie=87bcb734 desc=IGMP Snooping OK
[ 10.332000] [VLAN_MNGR] Registering: VID= 0 Member=001157d0 Policy=3 cookie=87bcb738 desc=IGMP Snooping OK
[ 10.340000] [VLAN_MNGR] Registering: VID= 0 Member=001155d0 Policy=3 cookie=87bcb73c desc=IGMP Snooping OK
[ 10.352000] [VLAN_MNGR] Registering: VID= 0 Member=0011ffe0 Policy=3 cookie=87bcb6c0 desc=Guest VLAN OK
[ 10.360000] [VLAN_CONFIG] vlanEnable:Disable
[ 10.364000] [VLAN_CONFIG] Aborting VLAN CONFIG!
[ 10.372000] [VLAN_MNGR] <01> Creating VLAN VID= 1 Member=001955d0 Desc:VLAN 1 For LAN
[ 10.380000] [VLAN_MNGR] <02> Creating VLAN VID= 2 Member=001bff50 Desc:VLAN 2 For WAN
[ 10.388000] [VLAN_MNGR] <03> Creating VLAN VID= 3 Member=0013fdd0 Desc:IGMP Snooping
[ 10.396000] [VLAN_MNGR] <04> Creating VLAN VID= 4 Member=0013f7d0 Desc:IGMP Snooping
[ 10.404000] [VLAN_MNGR] <05> Creating VLAN VID= 5 Member=0013f5d0 Desc:IGMP Snooping
[ 10.412000] [VLAN_MNGR] <06> Creating VLAN VID= 6 Member=0013dfd0 Desc:IGMP Snooping
[ [ 15.520000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
[ 15.604000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 15.720000] ath_dfs: Version 2.0.0
[ 15.720000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
usrconf_allocate_memory 212 shmget success id:43511 32769[ 16.164000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[ 16.976000] Read from 0X20000 to 0X20120: OK
[ 18.924000] ath_ahb: 10.2-00082-4 (Atheros/multi-bss)
[ 18.928000] __ath_attach: Set global_scn[0]
[ 18.944000] Enterprise mode: 0x53fc0000
[ 18.948000] Restoring Cal data from Flash
[ 18.956000] Green-AP : Green-AP : Attached
[ 18.956000]
[ 18.968000] ath_get_caps[6150] rx chainmask mismatch actual 7 sc_chainmak 0
[ 18.972000] ath_get_caps[6125] tx chainmask mismatch actual 7 sc_chainmak 0
[ 18.988000] ath_attach_dfs[12578] dfsdomain 1
[ 19.016000] SC Callback Registration for wifi0
[ 19.020000] wifi0: Atheros ???: mem=0xb8100000, irq=2
[ 19.024000] ath_pci: 10.2-00082-4 (Atheros/multi-bss)
[ 19.032000] ath_pci_probe
[ 19.032000] PCI device id is 003c :003c
[ 19.044000] ath_pci 0000:01:00.0: ath DEBUG: sc=0x86f46c00
[ 19.048000]
[ 19.048000] ol_ath_pci_configure : num_desired MSI set to 0
[ 19.056000]
[ 19.056000] Using PCI Legacy Interrupt
[ 19.872000] __ol_ath_attach: ath_attach TODO
[ 19.876000] __ol_ath_attach: dev name wifi1
[ 19.880000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
[ 19.892000] OL_ACBKMinfree : 0
[ 19.896000] OL_ACBEMinfree : 0
[ 19.896000] OL_ACVIMinfree : 0
[ 19.900000] OL_ACVOMinfree : 0
[ 19.904000] ol_ath_attach() BMI inited.
[ 19.908000] ol_ath_attach() BMI Get Target Info.
[ 19.912000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c
[ 19.920000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
[ 19.924000] ol_ath_attach() configure Target .
[ 19.932000] qc98xx_verify_checksum: flash checksum passed: 0x9a32
[ 19.940000] ol_transfer_bin_file 1882: Download Flash data len 2116
[ 19.956000] ol_transfer_bin_file 1827: Download Firmware data len 227320
[ 20.924000] ol_ath_attach() Download FW.
[ 20.928000] ol_ath_attach() HT Create .
[ 20.932000] ol_ath_attach() HIF Claim.
[ 20.936000] ol_ath_attach() BMI Done.
[ 20.940000] ol_ath_attach() WMI attached. wmi_handle 86e20000
[ 20.948000] +HWT
[ 20.952000] CE_recv_buf_enqueue 653 Populate last entry 512 for CE 5
[ 20.960000] CE_recv_buf_enqueue 662 CE 5 wi 511 dest_ptr 0x602d00 nbytes 0 recv_ctxt 0x86e14a60
[ 20.968000] -HWT
[ 20.972000] HTC Service:0x0300 ep:1 TX flow control disabled
[ 20.980000] CE_pkt_dl_len_set CE 4 Pkt download length 64
[ 20.988000] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from 86ed0000
[ 20.996000] HTC Service:0x0100 ep:2 TX flow control disabled
[ 21.004000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event
[ 21.012000] num_rf_chain : 00000003
[ 21.016000] ht_cap_info: : 0000085b
[ 21.020000] vht_cap_info : 338001b2
[ 21.020000] vht_supp_mcs : 0000ffea
[ 21.024000] LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256
[ 21.032000] idx 0 req 1 num_units 0 num_unit_info 2 unit size 444 actual units 145
[ 21.040000] chunk 0 len 64380 requested ,ptr 0x6ee0000
[ 21.056000] FIRMWARE:P 145 V 16 T 443
[ 21.056000]
[ 21.060000] FIRMWARE:_wlan_rtt_enable
[ 21.064000] wmi_ready_event_rx: WMI UNIFIED READY event
[ 21.072000] ol_ath_connect_htc() WMI is ready
[ 21.076000] ol_ath_set_host_app_area TODO
[ 21.080000] target uses HTT version 2.1; host uses 2.1
[ 21.092000] ol_ath_attach() connect HTC.
[ 21.096000] bypasswmi : 0
[ 21.096000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
[ 21.108000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
[ 21.116000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
[ 21.124000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
[ 21.128000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
[ 21.136000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
[ 21.144000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
[ 21.152000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
[ 21.160000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
[ 21.168000] Add VHT80 channel: 5210
[ 21.168000] Add VHT80 channel: 5290
[ 21.172000] Add VHT80 channel: 5530
[ 21.176000] Add VHT80 channel: 5610
[ 21.180000] Add VHT80 channel: 5690
[ 21.184000] Add VHT80 channel: 5775
[ 21.188000] Skipping VHT80 channel 5825
[ 21.192000] ol_ath_phyerr_attach: called
[ 21.196000] OL Resmgr Init-ed
[ 21.200000] Green-AP : Green-AP : Attached
[ 21.200000]
[ 21.204000] Green-AP : Attached
[ 21.208000] ol_if_dfs_setup: called
[ 21.212000] ol_if_dfs_attach: called; ptr=86ec9974, radar_info=87b21be0
[ 21.224000] ol_ath_rtt_meas_report_attach: called
[ 21.232000] ol_ath_attach() UMAC attach .
[ 21.236000] ol_if_dfs_configure: called
[ 21.240000] ol_if_dfs_configure: FCC domain
[ 21.244000] ol_if_dfs_disable: called
[ 21.248000] ol_ath_attach: Calling ol_if_dfs_configure
[ 21.252000] __ol_ath_attach: init tx/rx TODO
[ 21.256000] __ol_ath_attach: hard_header_len reservation 58
[ 21.264000] SC Callback Registration for wifi1
[ 21.448000] ath_attach_dfs[12578] dfsdomain 1
[ 21.560000] VAP device ath0 created
[ 21.640000]
[ 21.640000] DES SSID SET=TP-LINK_BF3A
[ 21.656000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
[ 21.664000] Set freq vap stop send + 86cd4000
[ 21.668000] Set freq vap stop send -86cd4000
[ 21.700000] Set wait done --86cd4000
[ 21.868000] Set freq vap stop send + 86cd4000
[ 21.872000] Set freq vap stop send -86cd4000
[ 21.904000] Set wait done --86cd4000
[ 21.932000] FWLOG: [39036] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 )
[ 21.940000] FWLOG: [39036] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 )
[ 21.948000] FWLOG: [39036] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 )
[ 21.956000] FWLOG: [39036] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 )
[ 21.964000] FWLOG: [39042] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 )
[ 21.972000] FWLOG: [39042] WHAL_ERROR_RESET_PM ( )
[ 25.768000] Interference detected
[ 25.768000] rx_clear=100, rx_frame=0, tx_frame=0
[ 26.244000] Scan in progress.. Cancelling it
[ 26.880000] athr_gmac_ring_alloc Allocated 3520 at 0x86ec7000
[ 26.888000] athr_gmac_ring_alloc Allocated 3520 at 0x87b1c000
[ 27.192000] 955x_GMAC: eth0 in RGMII MODE
[ 27.196000] Scorpion -----> S17 PHY
[ 27.204000] athrs17_reg_init_wan done
[ 27.208000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 27.212000] Setting PHY...
[ 27.216000] vid_offset is 0
[ 27.220000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 27.248000] device eth1 entered promiscuous mode
[ 27.352000] device ath0 entered promiscuous mode
[ 27.356000] br1: port 2(ath0) entering forwarding state
[ 27.676000]
[ 27.676000] Enet:1 port1 up
[ 27.680000] 955x_GMAC: enet unit:1 is up...
[ 27.684000] eth1 SGMII 1000Mbps full duplex
[ 27.688000] 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
[ 27.692000] 955x_GMAC: qca955x_soc_gmac_set_link Done
[ 27.696000] 955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
[ 27.704000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 28.168000] ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1
[ 28.176000] Scan in progress.. Cancelling it
[ 28.228000] br1: port 2(ath0) entering disabled state
[ 28.232000] DEVICE IS DOWN ifname=ath0
[ 28.240000] DEVICE IS DOWN ifname=ath0
[ 28.464000] br1: port 2(ath0) entering forwarding state
[ 29.220000] 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
[ 29.224000] 955x_GMAC: qca955x_soc_gmac_set_link Done
[ 29.228000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 29.236000] br1: port 1(eth1) entering forwarding state
[ 29.596000] Scan in progress.. Cancelling it
[ 29.652000] br1: port 2(ath0) entering disabled state
[ 29.692000] br1: starting userspace STP failed, starting kernel STP
[ 29.764000] br1: topology change detected, propagating
[ 29.772000] br1: port 2(ath0) entering forwarding state
====>>>>init5G...right region RU cur region:83
[ 29.832000] isCountryCodeValid: EEPROM regdomain 0x0
[ 29.836000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
[ 29.844000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
[ 29.852000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
[ 29.856000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
[ 29.864000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
[ 29.872000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
[ 29.880000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
[ 29.888000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
[ 29.892000] Add VHT80 channel: 5210
[ 29.896000] Add VHT80 channel: 5290
[ 29.900000] Add VHT80 channel: 5775
[ 29.904000] Skipping VHT80 channel 5660
[ 29.908000] Skipping VHT80 channel 5680
[ 29.912000] Skipping VHT80 channel 5700
[ 29.916000] Skipping VHT80 channel 5825
[ 29.952000] ath_ioctl: SIOC80211IFCREATE CALLED
[ 29.956000] wmi_unified_vdev_create_send: ID = 0 VAP Addr = 14:cc:20:5c:bf:39:
[ 29.964000] Setting dscp for vap id: 0
[ 29.968000] VAP device ath1 created
[ 30.024000]
[ 30.024000] DES SSID SET=TP-LINK_BF39_5G
[ 30.036000] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
[ 30.044000] Set freq vap stop send + 866a8000
[ 30.048000] OL vap_stop +
[ 30.052000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 30.060000] OL vap_stop -
[ 30.060000] STOPPED EVENT for vap 0 (86e20000)
[ 30.064000] Set freq vap stop send -866a8000
[ 30.096000] Set wait done --866a8000
[ 30.108000] ol_ath_desc_alloc_and_mark_for_mcast_clone: VAP Mcast to Unicast buffer allocated: 400
[ 30.116000] ol_ath_vap_set_param: VAP param is now supported param:66 value:2
[ 30.136000] Set freq vap stop send + 866a8000
[ 30.140000] OL vap_stop +
[ 30.144000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 30.148000] OL vap_stop -
[ 30.152000] STOPPED EVENT for vap 0 (86e20000)
[ 30.156000] Set freq vap stop send -866a8000
[ 30.188000] Set wait done --866a8000
[ 30.200000] OL vap_stop +
[ 30.204000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 30.208000] OL vap_stop -
[ 30.212000] STOPPED EVENT for vap 0 (86e20000)
[ 30.244000] wmi_unified_scan_start_send for vap 0 (86e20000)
[ 33.492000] Interference detected
[ 33.492000] rx_clear=99, rx_frame=0, tx_frame=0
[ 35.016000] OL vap_start +
[ 35.020000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 35.024000] OL vap_start -
[ 35.032000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 35.036000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 35.044000] ol_ath_wmm_update:
[ 35.044000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 35.052000] Notification to UMAC VAP layer
[ 35.264000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 35.268000] STOPPED EVENT for vap 0 (86e20000)
[ 35.528000] Interference detected
[ 35.528000] rx_clear=99, rx_frame=0, tx_frame=0
[ 35.752000] OL vap_stop +
[ 35.756000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 35.760000] OL vap_stop -
[ 35.764000] STOPPED EVENT for vap 0 (86e20000)
[ 35.796000] OL vap_start +
[ 35.800000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 35.804000] OL vap_start -
[ 35.808000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 35.812000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 35.820000] ol_ath_wmm_update:
[ 35.820000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 35.828000] Notification to UMAC VAP layer
[ 35.956000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 35.960000] STOPPED EVENT for vap 0 (86e20000)
[ 35.976000] OL vap_stop +
[ 35.980000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 35.984000] OL vap_stop -
[ 35.988000] STOPPED EVENT for vap 0 (86e20000)
[ 36.020000] OL vap_start +
[ 36.020000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 36.028000] OL vap_start -
[ 36.032000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 36.036000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 36.044000] ol_ath_wmm_update:
[ 36.044000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 36.052000] Notification to UMAC VAP layer
[ 36.068000] device ath1 entered promiscuous mode
[ 36.072000] br1: topology change detected, propagating
[ 36.076000] br1: port 3(ath1) entering forwarding state
[ 36.104000] ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1
[ 36.116000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 36.120000] STOPPED EVENT for vap 0 (86e20000)
[ 36.128000] br1: port 3(ath1) entering disabled state
[ 36.132000] DEVICE IS DOWN ifname=ath1
[ 36.136000] DEVICE IS DOWN ifname=ath1
[ 36.304000] OL vap_stop +
[ 36.304000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 36.312000] OL vap_stop -
[ 36.312000] STOPPED EVENT for vap 0 (86e20000)
[ 36.348000] OL vap_start +
[ 36.352000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 36.356000] OL vap_start -
[ 36.360000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 36.364000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 36.372000] ol_ath_wmm_update:
[ 36.372000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 36.380000] Notification to UMAC VAP layer
[ 36.384000] br1: topology change detected, propagating
[ 36.388000] br1: port 3(ath1) entering forwarding state
[ 36.556000] Interference detected
[ 36.556000] rx_clear=100, rx_frame=0, tx_frame=0
[ 36.824000] FWLOG: [54384] WAL_DBGID_BB_WDOG_TRIGGERED ( 0xd470, 0x200008a, 0x0, 0x60 )
[ 36.832000] FWLOG: [54767] WAL_DBGID_SECURITY_ENCR_EN ( )
[ 36.836000] FWLOG: [54767] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
[ 36.844000] FWLOG: [54954] WAL_DBGID_BB_WDOG_TRIGGERED ( 0xd6aa, 0x200008a, 0x0, 0x61 )
[ 38.128000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 38.132000] STOPPED EVENT for vap 0 (86e20000)
[ 38.140000] br1: port 3(ath1) entering disabled state
[ 38.188000] OL vap_stop +
[ 38.192000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 38.196000] OL vap_stop -
[ 38.200000] STOPPED EVENT for vap 0 (86e20000)
[ 38.232000] OL vap_start +
[ 38.236000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 38.240000] OL vap_start -
[ 38.244000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 38.248000] Interference detected
[ 38.248000] rx_clear=100, rx_frame=0, tx_frame=0
[ 38.256000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 38.264000] ol_ath_wmm_update:
[ 38.264000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 38.272000] Notification to UMAC VAP layer
[ 38.288000] br1: topology change detected, propagating
[ 38.292000] br1: port 3(ath1) entering forwarding state
[ 38.392000] port is 21, val is off
[ 38.396000] set port 21 off
[ 38.408000] port is 22, val is off
[ 38.412000] set port 22 off
[ 39.296000] Interference detected
[ 39.296000] rx_clear=99, rx_frame=0, tx_frame=0
[ 39.428000] port is 21, val is on
[ 39.432000] set port 21 on
[ 39.444000] port is 22, val is on
[ 39.448000] set port 22 on
[ 39.872000] fuse init (API version 7.12)
[ 40.104000] usbcore: registered new interface driver usbfs
[ 40.108000] usbcore: registered new interface driver hub
[ 40.116000] usbcore: registered new device driver usb
[ 40.152000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 40.156000] Port Status 1c000004
[ 40.160000] ath-ehci ath-ehci.0: ATH EHCI
[ 40.164000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
[ 40.172000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 40.180000] ehci_reset Port Status 1c000000
[ 40.184000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
[ 40.192000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 40.200000] ehci_reset Port Status 1c000000
[ 40.216000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
[ 40.220000] usb usb1: configuration #1 chosen from 1 choice
[ 40.224000] hub 1-0:1.0: USB hub found
[ 40.228000] hub 1-0:1.0: 1 port detected
[ 40.236000] Port Status 1c000000
[ 40.236000] ath-ehci1 ath-ehci1.1: ATH EHCI
[ 40.240000] ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
[ 40.252000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 40.256000] ehci_reset Port Status 1c000000
[ 40.260000] ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
[ 40.268000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 40.276000] ehci_reset Port Status 1c000000
[ 40.292000] ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
[ 40.296000] usb usb2: configuration #1 chosen from 1 choice
[ 40.304000] hub 2-0:1.0: USB hub found
[ 40.304000] hub 2-0:1.0: 1 port detected
[ 40.324000] Interference detected
[ 40.324000] rx_clear=100, rx_frame=0, tx_frame=0
[ 40.572000] SCSI subsystem initialized
[ 40.896000] Initializing USB Mass Storage driver...
[ 40.904000] usbcore: registered new interface driver usb-storage
[ 40.908000] USB Mass Storage support registered.
[ 41.008000] kcg 333 :GPL NetUSB up!
[ 41.296000] kc 90 : run_telnetDBGDServer start
[ 41.300000] kc 227 : init_DebugD end
[ 41.304000] INFO17E0: NetUSB 1.02.65.5, 0002061F : Apr 21 2015 15:30:36
[ 41.312000] INFO17E2: 7437: Archer C7 v2 :Archer C7 v2
[ 41.316000] INFO17E3: AUTH ISOC
[ 41.320000] INFO17E4: filterAudio
[ 41.324000] usbcore: registered new interface driver KC NetUSB General Driver
[ 41.332000] INFO0145: init proc : PAGE_SIZE 4096
[ 41.340000] INFO16D4: infomap 85c4be3c
[ 41.344000] INFO16D7: sleep to wait br0 to wake up
[ 41.348000] INFO15A7: tcpConnector() started... : br0
[ 41.824000] IPv6 over IPv4 tunneling driver
[ 42.256000] Interference detected
[ 42.256000] rx_clear=100, rx_frame=0, tx_frame=0
[ 43.284000] Interference detected
[ 43.284000] rx_clear=100, rx_frame=0, tx_frame=0
[ 43.988000] br1: port 2(ath0) entering disabled state
[ 44.044000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 44.052000] STOPPED EVENT for vap 0 (86e20000)
[ 44.188000] br1: port 3(ath1) entering disabled state
[ 44.380000] INFO155A: Bind to br0
check success
Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: Admin
login: no valid shadow password

Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: admin
Password:
Login incorrect

Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: Admin
login: no valid shadow password
Подскажите что можно попробовать еще?
  0      
  0      
#1
Опции

Информация

Поблагодарили: 0

Просмотры: 4959

Ответы: 0

Статьи по теме