Переделка Archer c1200v2 в ASUS-RT-AC1200G+
Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.
Переделка Archer c1200v2 в ASUS-RT-AC1200G+
Build Date: Tue Apr 26 14:47:17 CST 2016 (chengche@ubuntu)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=900,*533*
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.27 (r584393)
CPU type 0x0: 900MHz
Tot mem: 131072 KBytes
CFE mem: 0x00F00000 - 0x01795EF0 (9002736)
Data: 0x00F5E400 - 0x00F5E998 (1432)
BSS: 0x00F5E9A8 - 0x00F93EF0 (218440)
Heap: 0x00F93EF0 - 0x01793EF0 (8388608)
Stack: 0x01793EF0 - 0x01795EF0 (8192)
Text: 0x00F00000 - 0x00F5428C (344716)
Device eth0: hwaddr 00-90-4C-1E-20-01, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Hello!! Enter Rescue Mode: (by Force)
Reading ::
Flash Device=flash1.trx
TFTP Server.
..tftp retry wait 0
..tftp retry wait 1
..tftp retry wait 2
Failed.: Timeout occured
Reading ::
Flash Device=flash1.trx
TFTP Server.
..tftp retry wait 0
прошивка boot от tp-link
CFE> flash -noheader 192.168.1.10:boot.bin flash1.boot
Reading 192.168.1.10:boot.bin:
Flash Device=flash1.boot
TFTP Client.
- last blk -
- Last block -
Done. 171261 bytes read
.Download of 0x29cfd bytes Completed
Write bootloader binary to FLASH (0xbfc00000)
Programming...copysize=171261, amtcopy=171261
done. 171261 bytes written
Decompressing...done
CFE version 9.10.178.50 (r635252) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Wed Dec 14 16:30:49 CST 2016 (seal@seal-pc)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=900,*533*
No GPIO defined for BBSI interface
No BBSI device
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.50 (r635252)
CPU type 0x0: 900MHz
Tot mem: 131072 KBytes
CFE mem: 0x00F00000 - 0x02FB1ACC (34282188)
Data: 0x00F6933C - 0x00F69AD8 (1948)
BSS: 0x00F69AE8 - 0x00FAFACC (286692)
Heap: 0x00FAFACC - 0x02FAFACC (33554432)
Stack: 0x02FAFACC - 0x02FB1ACC (8192)
Text: 0x00F00000 - 0x00F5D4EC (382188)
Committing NVRAM...done
ЗDecompressing...doneton release...done
CFE version 9.10.178.50 (r635252) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Wed Dec 14 16:30:49 CST 2016 (seal@seal-pc)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=900,*533*
No GPIO defined for BBSI interface
No BBSI device
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.50 (r635252)
CPU type 0x0: 900MHz
Tot mem: 131072 KBytes
CFE mem: 0x00F00000 - 0x02FB1ACC (34282188)
Data: 0x00F6933C - 0x00F69AD8 (1948)
BSS: 0x00F69AE8 - 0x00FAFACC (286692)
Heap: 0x00FAFACC - 0x02FAFACC (33554432)
Stack: 0x02FAFACC - 0x02FB1ACC (8192)
Text: 0x00F00000 - 0x00F5D4EC (382188)
Device eth0: hwaddr 00-90-4C-1E-20-01, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: Image compressed with unsupported method
Failed.
Could not load flash0.os:: Unsupported function
Reading 192.168.1.10:boot-rt.bin: Done. 262144 bytes read
Programming...done. 262144 bytes written
*** command status = 0
CFE> reboot
Decompressing...done
CFE version 9.10.178.27 (r584393) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Tue Apr 26 14:47:17 CST 2016 (chengche@ubuntu)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=900,*533*
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.27 (r584393)
CPU type 0x0: 900MHz
Tot mem: 131072 KBytes
CFE mem: 0x00F00000 - 0x01795EF0 (9002736)
Data: 0x00F5E400 - 0x00F5E998 (1432)
BSS: 0x00F5E9A8 - 0x00F93EF0 (218440)
Heap: 0x00F93EF0 - 0x01793EF0 (8388608)
Stack: 0x01793EF0 - 0x01795EF0 (8192)
Text: 0x00F00000 - 0x00F5428C (344716)
Committing NVRAM...done
Device eth0: hwaddr 00-90-4C-1E-20-01, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
boot the image...
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .... 4167488 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: squash filesystem found at block 30
Creating 5 MTD partitions on "bcmsflash":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000ff0000 : "linux"
0x0000001e2d90-0x000000f60000 : "rootfs"
0x000000f60000-0x000000ff0000 : "jffs2"
0x000000ff0000-0x000001000000 : "nvram"
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== PPTP init ===
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1962 buckets, 7848 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <
All bugs added by David S. Miller <
Registering the dns_resolver key type
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
devtmpfs: mounted
Freeing init memory: 192K
## mknod /dev/null: File exists
## mknod /dev/console: File exists
1: set_action 0
Hit ENTER for console...
firmware version: 3.0.0.4.382_52272-g73d3ea2
[1 preinit:init_nvram +5] init_nvram for model(68)
## Restoring defaults... ##
done
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x1
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
bcm_robo_enable_switch: EEE is disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.61 (r667680)
hotplug net INTERFACE=eth0 ACTION=add
config_location(0x0045): [tcode] location is []
config_location(0x0048): [tcode] no location setting, using default location
config_location(0x005e): [tcode] config location: [0:ccode]=[E0], [0:regrev]=[943]
config_location(0x0068): [tcode] set_wl_country, 0, [E0], [943]
config_location(0x007e): [tcode] config location 5G: [sb/1/ccode]=[E0], [sb/1/regrev]=[943]
config_location(0x0089): [tcode] set_wl_country, 1, [E0], [943]
set_wltxpower(0x01d8): [rc] no Power Control on this model
wl_module_init: passivemode set to 0x0
wl_module_init: txworkq set to 0x1
PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
eth1: Broadcom BCM43227 802.11 Wireless Controller 9.10.178.61 (r667680)
hotplug net INTERFACE=eth1 ACTION=add
eth2: Broadcom BCM43c8 802.11 Wireless Controller 9.10.178.61 (r667680)
hotplug net INTERFACE=eth2 ACTION=add
1: check_action 0
start jffs2: 3, 589824
1: check_action 0
1: set_action 6
Unlocking 0x0 - 0xffff
Unlocking 0x10000 - 0x1ffff
Unlocking 0x20000 - 0x2ffff
Unlocking 0x30000 - 0x3ffff
Unlocking 0x40000 - 0x4ffff
Unlocking 0x50000 - 0x5ffff
Unlocking 0x60000 - 0x6ffff
Unlocking 0x70000 - 0x7ffff
Unlocking 0x80000 - 0x8ffff
1: set_action 0
"jffs2" successfully unlocked.
Clean /jffs/*
start_logger:
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
hotplug net INTERFACE=vlan1 ACTION=add
hotplug net INTERFACE=vlan2 ACTION=add
update_lan_state(lan_, 0, 0)
generate_wl_para(0x0b6c): unit 0 subunit -1
generate_wl_para(0x0f0a): bw: 0
generate_wl_para(0x0f0c): chanspec: 0
generate_wl_para(0x0f0d): bw_cap: 3
generate_wl_para(0x0f13): obss_coex: 1
wlconf_pre(0x10cb): set vhtmode 0
generate_wl_para(0x0b6c): unit 1 subunit -1
generate_wl_para(0x0f0a): bw: 0
generate_wl_para(0x0f0c): chanspec: 0
generate_wl_para(0x0f0d): bw_cap: 7
generate_wl_para(0x0f13): obss_coex: 0
wlconf_pre(0x10c6): set vhtmode 1
vlan1: cmd=14 (errno 95): Operation not supported
_ifconfig: name=vlan1 flags=1243 IFUP addr= netmask=
_ifconfig: name=eth1 flags=1243 IFUP addr= netmask=
hotplug net INTERFACE=br0 ACTION=add
generate_wl_para(0x0b6c): unit 0 subunit -1
generate_wl_para(0x0f0a): bw: 0
generate_wl_para(0x0f0c): chanspec: 0
generate_wl_para(0x0f0d): bw_cap: 3
generate_wl_para(0x0f13): obss_coex: 1
generate_wl_para(0x0b6c): unit 0 subunit 1
generate_wl_para(0x0b6c): unit 0 subunit 2
generate_wl_para(0x0b6c): unit 0 subunit 3
_ifconfig: name=eth2 flags=1243 IFUP addr= netmask=
generate_wl_para(0x0b6c): unit 1 subunit -1
generate_wl_para(0x0f0a): bw: 0
generate_wl_para(0x0f0c): chanspec: 0
generate_wl_para(0x0f0d): bw_cap: 7
generate_wl_para(0x0f13): obss_coex: 0
generate_wl_para(0x0b6c): unit 1 subunit 1
generate_wl_para(0x0b6c): unit 1 subunit 2
generate_wl_para(0x0b6c): unit 1 subunit 3
start_lan: setting MAC address of bridge br0 as 00:90:4C:1E:20:01
_ifconfig: name=br0 flags=1243 IFUP addr=192.168.1.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
update_lan_state(lan_, 2, 0)
nat_rule: stop_nat_rules 1.
stop_nat_rules: apply the redirect_rules state 0 ret 0
start_lan 2762
# wanduck: Got LAN(-1) information:
# Enable direct rule
wanduck(1): SIM or modem is pulled off.
[1 preinit:start_dnsmasq +15] begin
[1 preinit:stop_dnsmasq +15] begin
[1 preinit:stop_dnsmasq +15] end
[1 preinit:start_dnsmasq +16] end
start_lan_port(0) 1
TZ watchdog
decomp: fname=/var/lib/misc/rstats-speed.gz
decomp: gzip -dc /var/lib/misc/rstats-speed.gz > /var/tmp/rstats-uncomp != 0
load: speed_count = 0
load: read source= save_path=
load_history: fname=/var/lib/misc/rstats-history.gz
decomp: fname=/var/lib/misc/rstats-history.gz
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
decomp: fname=/var/lib/misc/rstats-history.gz
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
load_history: load failed
msgget ok
disk_monitor: starting...
disk_monitor: day=5, week=6, time=5:5.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=64800...
disk_monitor: wait_second=64800...
disk_monitor: Pause...
vlan1: cmd=14 (errno 95): Operation not supported
_ifconfig: name=eth1 flags=0000 addr= netmask=
_ifconfig: name=eth2 flags=0000 addr= netmask=
catch_sig(0x0ee9): [watchdog] Handle WPS LED for WPS Stop
[1 preinit:init_nvram +17] init_nvram for model(68)
config_location(0x0045): [tcode] location is []
config_location(0x0048): [tcode] no location setting, using default location
config_location(0x005e): [tcode] config location: [0:ccode]=[E0], [0:regrev]=[943]
config_location(0x0068): [tcode] set_wl_country, 0, [E0], [943]
config_location(0x007e): [tcode] config location 5G: [sb/1/ccode]=[E0], [sb/1/regrev]=[943]
config_location(0x0089): [tcode] set_wl_country, 1, [E0], [943]
set_wltxpower(0x01d8): [rc] no Power Control on this model
generate_wl_para(0x0b6c): unit 0 subunit -1
generate_wl_para(0x0f0a): bw: 0
generate_wl_para(0x0f0c): chanspec: 0
generate_wl_para(0x0f0d): bw_cap: 3
generate_wl_para(0x0f13): obss_coex: 1
wlconf_pre(0x10cb): set vhtmode 0
generate_wl_para(0x0b6c): unit 1 subunit -1
generate_wl_para(0x0f0a): bw: 0
generate_wl_para(0x0f0c): chanspec: 0
generate_wl_para(0x0f0d): bw_cap: 7
generate_wl_para(0x0f13): obss_coex: 0
wlconf_pre(0x10c6): set vhtmode 1
vlan1: cmd=14 (errno 95): Operation not supported
_ifconfig: name=eth1 flags=1243 IFUP addr= netmask=
generate_wl_para(0x0b6c): unit 0 subunit -1
generate_wl_para(0x0f0a): bw: 0
generate_wl_para(0x0f0c): chanspec: 0
generate_wl_para(0x0f0d): bw_cap: 3
generate_wl_para(0x0f13): obss_coex: 1
generate_wl_para(0x0b6c): unit 0 subunit 1
generate_wl_para(0x0b6c): unit 0 subunit 2
generate_wl_para(0x0b6c): unit 0 subunit 3
_ifconfig: name=eth2 flags=1243 IFUP addr= netmask=
generate_wl_para(0x0b6c): unit 1 subunit -1
generate_wl_para(0x0f0a): bw: 0
generate_wl_para(0x0f0c): chanspec: 0
generate_wl_para(0x0f0d): bw_cap: 7
generate_wl_para(0x0f13): obss_coex: 0
generate_wl_para(0x0b6c): unit 1 subunit 1
generate_wl_para(0x0b6c): unit 1 subunit 2
generate_wl_para(0x0b6c): unit 1 subunit 3
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x100a (10)
acsd: Adjusted channel spec: 0x100a (10)
acsd: selected channel spec: 0x100a (10)
acsd: acs_set_chspec: 0x100a (10) for reason APCS_INIT
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0xe06a (100/80)
acsd: Adjusted channel spec: 0xe06a (100/80)
acsd: selected DFS-exit channel spec: 0xe06a (100/80)
acsd: selected channel spec: 0xe06a (100/80)
acsd: Adjusted channel spec: 0xe06a (100/80)
acsd: selected channel spec: 0xe06a (100/80)
acsd: acs_set_chspec: 0xe06a (100/80) for reason APCS_INIT
vlan1: cmd=14 (errno 95): Operation not supported
start_wan: start_wan_if(0)!
[1 preinit:start_wan_if +27] unit=0.
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
update_wan_state(wan0_, 1, 0)
start_wan_if(0x0650): ifup:eth0
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
start_wan_if(0x0654): start auth:0
start_auth:: done
start_wan_if(0x065e): start udhcpc:eth0, 0
start_wan_if(): End.
udhcpc_wan:: deconfig
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
wan_down(eth0)
wan_down(eth0): .
stop_auth:: done
route_manip: cmd=DEL name=eth0 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
[Mastiff]init
start_usb
no tune_bdflush
[1 preinit:init_main +30] recv signal 14 from pid [1:/sbin/preinit] (from user)
udhcpc_wan:: leasefail
RT-AC1200G+ login:
У меня ощущение, что кнопка ресета в тп-линке и асусе сидят на разных gpio, поэтому при холодном старте отрабатывает вход в recovery mode. Как бы победить сию проблему