TPlink 3040 v1 восстановление

Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.

TPlink 3040 v1 восстановление

Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.
TPlink 3040 v1 восстановление
TPlink 3040 v1 восстановление
2014-02-13 15:04:25
TP link 3040 v1, залил open wrt. Доигрался, что то не так сконфигурировал,

модем выпал в какое то состояние и теперь через WEB, telnet? ssh никак не

отзывается...
Припаял COM port, вижу процесс загрузки:

=============================================================================
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc

ve rsion 4.6.3 20120201

(prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Nov 18 04:31

:55 UTC 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz,

Ref:25.00 0MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total

pag es: 8128
[ 0.000000] Kernel command line: board=TL-MR3040 console=ttyATH0,115200

root fstype=squashfs,jffs2

noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32

bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize

32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29008k/32768k available (2209k kernel code, 3760k

reserve d, 412k data, 212k init,

0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,

No des=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-MR3040
[ 0.350000] bio: create slab <bio-0> at 0
[ 0.360000] Switching to clocksource MIPS
[ 0.360000] NET: Registered protocol family 2
[ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.370000] TCP established hash table entries: 1024 (order: 1, 8192

bytes)
[ 0.370000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.390000] TCP reno registered
[ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] NET: Registered protocol family 1
[ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)

(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.440000] msgmni has been set to 56
[ 0.440000] Block layer SCSI generic (bsg) driver version 0.4 loaded

(major 254)
[ 0.450000] io scheduler noop registered
[ 0.450000] io scheduler deadline registered (default)
[ 0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X

UART
[ 0.480000] console [ttyATH0] enabled, bootconsole disabled
[ 0.480000] console [ttyATH0] enabled, bootconsole disabled
[ 0.490000] m25p80 spi0.0: found s25sl032a, expected m25p80
[ 0.500000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
[ 0.500000] 5 tp-link partitions found on MTD device spi0.0
[ 0.510000] Creating 5 MTD partitions on "spi0.0":
[ 0.510000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.520000] 0x000000020000-0x000000109820 : "kernel"
[ 0.520000] mtd: partition "kernel" must either start or end on erase

block boundary or be smaller than an erase block -- forcing read-only
[ 0.540000] 0x000000109820-0x0000003f0000 : "rootfs"
[ 0.540000] mtd: partition "rootfs" must either start or end on erase

block boundary or be smaller than an erase block -- forcing read-only
[ 0.550000] mtd: partition "rootfs" set to be root filesystem
[ 0.560000] mtd: partition "rootfs_data" created automatically,

ofs=2E0000, len=110000
[ 0.570000] 0x0000002e0000-0x0000003f0000 : "rootfs_data"
[ 0.570000] 0x0000003f0000-0x000000400000 : "art"
[ 0.580000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.600000] ag71xx_mdio: probed
[ 0.610000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.160000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:00

[uid=004dd041, driver=Generic PHY]
[ 1.170000] TCP cubic registered
[ 1.170000] NET: Registered protocol family 17
[ 1.180000] Bridge firewalling registered
[ 1.180000] 8021q: 802.1Q VLAN Support v1.8
[ 1.190000] VFS: Mounted root (squashfs filesystem) readonly on device

31:2.
[ 1.200000] Freeing unused kernel memory: 212k freed
- preinit -
tPress the [f] key and hit [enter] to enter failsafe mode
tpl
- regular preinit -
[ 5.870000] JFFS2 notice: (438) jffs2_build_xattr_subsystem: complete

building xattr subsystem, 20 of xdatum (0 unchecked, 19 orphan) and 29 of

xref (0 dead, 19 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [ 7.650000] Compat-drivers

backport release: compat-drivers-2012-09-04-2-gddac993
[ 7.650000] Backport based on wireless-testing.git master-2012-09-07
[ 7.660000] compat.git: wireless-testing.git
[ 7.690000] cfg80211: Calling CRDA to update world regulatory domain
[ 7.700000] cfg80211: World regulatory domain updated:
[ 7.700000] cfg80211: (start_freq - end_freq @ bandwidth),

(max_antenna_gain, max_eirp)
[ 7.710000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[ 7.720000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,

2000 mBm)
[ 7.720000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,

2000 mBm)
[ 7.730000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[ 7.740000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[ 8.090000] usbcore: registered new interface driver usbfs
[ 8.090000] usbcore: registered new interface driver hub
[ 8.100000] usbcore: registered new device driver usb
[ 8.660000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 8.660000] cfg80211: Calling CRDA for country: US
[ 8.670000] cfg80211: Regulatory domain changed to country: US
[ 8.670000] cfg80211: (start_freq - end_freq @ bandwidth),

(max_antenna_gain, max_eirp)
[ 8.680000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,

2700 mBm)
[ 8.690000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,

1700 mBm)
[ 8.700000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[ 8.700000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[ 8.710000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[ 8.720000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,

3000 mBm)
[ 8.780000] PPP generic driver version 2.4.2
[ 9.030000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.260000] NET: Registered protocol family 24
[ 9.270000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.280000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 9.290000] ehci-platform ehci-platform: new USB bus registered, assigned

bus number 1
[ 9.320000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 9.340000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 9.340000] hub 1-0:1.0: USB hub found
[ 9.340000] hub 1-0:1.0: 1 port detected
[ 9.370000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 9.610000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 12.700000] device eth0 entered promiscuous mode
[ 14.440000] cfg80211: Calling CRDA for country: RU
[ 14.450000] cfg80211: Regulatory domain changed to country: RU
[ 14.450000] cfg80211: (start_freq - end_freq @ bandwidth),

(max_antenna_gain, max_eirp)
[ 14.460000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A,

2000 mBm)
[ 14.470000] cfg80211: (5735000 KHz - 5835000 KHz @ 20000 KHz), (N/A,

3000 mBm)
[ 16.280000] device wlan0 entered promiscuous mode
[ 16.370000] br-lan: port 2(wlan0) entered forwarding state
[ 16.370000] br-lan: port 2(wlan0) entered forwarding state

Здесь терминал пишет что потерял связь с прибором...
Мне удавалось получить доступ, нажимая вроде F вываливался в командную

строку. На форумах нашел, что надо жать "tpl", но похоже до этого места мой

роутер не догружается. Причем я это все делаю, питая роутер от COM порта, не

включая его питания.
А что дальше? как обновить прошивку или поправить конфиг. Но сначала надо

найти, что там не так. Какова методика поиска?

============================================================================
  0      
  0      
#1
Опции

Информация

Поблагодарили: 0

Просмотры: 1905

Ответы: 0