TPlink 3040 v1 восстановление
Эта ветка закрыта для дальнейших ответов. Вы можете создать новую тему, чтобы поделиться своими идеями или задать вопросы.
TPlink 3040 v1 восстановление
модем выпал в какое то состояние и теперь через WEB, telnet? ssh никак не
отзывается...
Припаял COM port, вижу процесс загрузки:
=============================================================================
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc
ve rsion 4.6.3 20120201
(prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Nov 18 04:31
:55 UTC 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz,
Ref:25.00 0MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pag es: 8128
[ 0.000000] Kernel command line: board=TL-MR3040 console=ttyATH0,115200
root fstype=squashfs,jffs2
noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize
32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29008k/32768k available (2209k kernel code, 3760k
reserve d, 412k data, 212k init,
0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
No des=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-MR3040
[ 0.350000] bio: create slab <bio-0> at 0
[ 0.360000] Switching to clocksource MIPS
[ 0.360000] NET: Registered protocol family 2
[ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.370000] TCP established hash table entries: 1024 (order: 1, 8192
bytes)
[ 0.370000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.390000] TCP reno registered
[ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] NET: Registered protocol family 1
[ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.440000] msgmni has been set to 56
[ 0.440000] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 254)
[ 0.450000] io scheduler noop registered
[ 0.450000] io scheduler deadline registered (default)
[ 0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X
UART
[ 0.480000] console [ttyATH0] enabled, bootconsole disabled
[ 0.480000] console [ttyATH0] enabled, bootconsole disabled
[ 0.490000] m25p80 spi0.0: found s25sl032a, expected m25p80
[ 0.500000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
[ 0.500000] 5 tp-link partitions found on MTD device spi0.0
[ 0.510000] Creating 5 MTD partitions on "spi0.0":
[ 0.510000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.520000] 0x000000020000-0x000000109820 : "kernel"
[ 0.520000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.540000] 0x000000109820-0x0000003f0000 : "rootfs"
[ 0.540000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.550000] mtd: partition "rootfs" set to be root filesystem
[ 0.560000] mtd: partition "rootfs_data" created automatically,
ofs=2E0000, len=110000
[ 0.570000] 0x0000002e0000-0x0000003f0000 : "rootfs_data"
[ 0.570000] 0x0000003f0000-0x000000400000 : "art"
[ 0.580000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.600000] ag71xx_mdio: probed
[ 0.610000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.160000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:00
[uid=004dd041, driver=Generic PHY]
[ 1.170000] TCP cubic registered
[ 1.170000] NET: Registered protocol family 17
[ 1.180000] Bridge firewalling registered
[ 1.180000] 8021q: 802.1Q VLAN Support v1.8
[ 1.190000] VFS: Mounted root (squashfs filesystem) readonly on device
31:2.
[ 1.200000] Freeing unused kernel memory: 212k freed
- preinit -
tPress the [f] key and hit [enter] to enter failsafe mode
tpl
- regular preinit -
[ 5.870000] JFFS2 notice: (438) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 20 of xdatum (0 unchecked, 19 orphan) and 29 of
xref (0 dead, 19 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 7.650000] Compat-drivers
backport release: compat-drivers-2012-09-04-2-gddac993
[ 7.650000] Backport based on wireless-testing.git master-2012-09-07
[ 7.660000] compat.git: wireless-testing.git
[ 7.690000] cfg80211: Calling CRDA to update world regulatory domain
[ 7.700000] cfg80211: World regulatory domain updated:
[ 7.700000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 7.710000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 7.720000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 7.720000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 7.730000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 7.740000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 8.090000] usbcore: registered new interface driver usbfs
[ 8.090000] usbcore: registered new interface driver hub
[ 8.100000] usbcore: registered new device driver usb
[ 8.660000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 8.660000] cfg80211: Calling CRDA for country: US
[ 8.670000] cfg80211: Regulatory domain changed to country: US
[ 8.670000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 8.680000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2700 mBm)
[ 8.690000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
1700 mBm)
[ 8.700000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 8.700000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 8.710000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 8.720000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
3000 mBm)
[ 8.780000] PPP generic driver version 2.4.2
[ 9.030000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.260000] NET: Registered protocol family 24
[ 9.270000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.280000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 9.290000] ehci-platform ehci-platform: new USB bus registered, assigned
bus number 1
[ 9.320000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 9.340000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 9.340000] hub 1-0:1.0: USB hub found
[ 9.340000] hub 1-0:1.0: 1 port detected
[ 9.370000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 9.610000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 12.700000] device eth0 entered promiscuous mode
[ 14.440000] cfg80211: Calling CRDA for country: RU
[ 14.450000] cfg80211: Regulatory domain changed to country: RU
[ 14.450000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 14.460000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm)
[ 14.470000] cfg80211: (5735000 KHz - 5835000 KHz @ 20000 KHz), (N/A,
3000 mBm)
[ 16.280000] device wlan0 entered promiscuous mode
[ 16.370000] br-lan: port 2(wlan0) entered forwarding state
[ 16.370000] br-lan: port 2(wlan0) entered forwarding state
Здесь терминал пишет что потерял связь с прибором...
Мне удавалось получить доступ, нажимая вроде F вываливался в командную
строку. На форумах нашел, что надо жать "tpl", но похоже до этого места мой
роутер не догружается. Причем я это все делаю, питая роутер от COM порта, не
включая его питания.
А что дальше? как обновить прошивку или поправить конфиг. Но сначала надо
найти, что там не так. Какова методика поиска?
============================================================================