Controllers

TP-Link Omada Cloud SDN integrates Omada Devices including EAPs, JetStream Switches and Omada Routers, all are centrally managed with an Omada SDN Controller. Anything related to TP-Link's Omada SDN Controller, welcome to ask questions, join discussions and share your experience/knowledge here.
Controllers

Tags

Label

 
I have following configuration for my office. Here, I have statically assigned address (192.168.0.0/16) for my clients below my cisco gateway. Controller gets 192.168.2.112, and ER605 gets 192.168.254
ControllerAdoption
By airplasma · Latest post a week ago by Vincent-TP
0Helpful
113Views
5Replies
Hi all, Im trying to migrate a ER7212 system to an OC200+ER605+SG2008P, because i need the extra capabilities, since the system is gonna be expanding beneath 10 devices shortly. whenever I try to impo
Firmware UpdateControllerAdoptionMigration
By maximosg · Latest post 2 weeks ago by Vincent-TP
1Helpful
271Views
5Replies
I am attempting to add my ER8411 and SG3428MP to the Software controller. I have them all connected directly on the same network, but the devices will not appear in the Software controller for me to a
ControllerAdoption
By Jcount · Latest post 2025-06-11 06:46:52 by Vincent-TP
0Helpful
116Views
1Replies
Omada Software Controller (v.5.15.20.2) Need help with this, I can't add devices to this controller the status always "ADOPT FAILED" and I don't know where the controller get the IP assigned to these
ControllerAdoption
By SCPI_MIS · Latest post 2025-04-30 23:18:11 by GRL
2Helpful
434Views
11Replies
Hello, got strange problem. Got vlan1 with ip on omada 192.168.100.99/24 and try adopt switch TL-SG3428X v1.0 (HW 1.0.2) with ip 192.168.100.54/24 and after adopt, omada reverse ip switch from ip on n
Adoption
By mati1990 · Latest post 2025-04-25 07:13:07 by GRL
0Helpful
464Views
6Replies
hi, why you dont add configurable ports on sites? Controller oc400 has 4 rj45 and 2sfp+ and why need use routing firewalls policy to roks controller with multiple real network? i have almost 100 switc
ControllerAdoption
By mati1990 · Latest post 2025-04-25 06:30:45 by Vincent-TP
1Helpful
155Views
2Replies
Hello, i have installed a software controller in my VLAN20. How can i adopt my SG2008P? I deleted the VLAN1 Interface from the switch at the beginning and only use it in my VLAN 20 (management). The c
ControllerVLAN & Multi-NetworksAdoption
By luck3rhoch3 · Latest post 2025-04-23 08:05:49 by Vincent-TP
0Helpful
238Views
4Replies
Hello, I have 4 different locations on the omada controller,I have a problem with one. Every few days, all devices in that one location stuck in the "adopting". IPsec VPN connection works between thes
ControllerAdoption
By dadziuk · Latest post 2025-04-18 09:11:01 by Vincent-TP
1Helpful
347Views
7Replies
Dear All, According to the release Notes of the ER-7206 V2.20 20250228 this Firmware is fully adapted to Omada SDN 5.15.20.7 and above. Unfortunately this is not fully true and I have explained this i
ControllerFirmware UpdateAdoptionVirtual WAN
By TheMuk · Latest post 2025-04-18 07:35:59 by Vincent-TP
1Helpful
214Views
1Replies
Hello, Good day. Should it be possible to set up the management on VLAN20, or is it strictly required to use VLAN1 for management? I made small home lab, where I tried it. devices: - Omada Controller,
ControllerAdoptionVLAN & Multi-Networks
By Petrmann · Latest post 2025-03-14 18:09:31 by Petrmann
0Helpful
380Views
3Replies
123...
123...