Pharos Wireless Broadband Forums

Setting up CPE710, have 2 CPE710. one running in AP mode and the other in Client mode. My use case is the following. Need the 2 CPE701 to connect to each other (done and working). Need to send multipl

Highlighted Thread

By sssp · Latest post 2021-11-04 13:31:59 by shadowwild

1Helpful

2271Views

11Replies

Help with setup of CPE510 as Access Point and CPE210 as Client

I'm in desperate need of assistance in the initial setup of CPE510 and CPE210. After reading a few other posts I'm hoping I have the right equipment for my needs. My goal is to set up two CPE510 as Ac

Highlighted Thread

By MarcotteMW · Latest post 2022-05-31 14:18:14 by Egoconcentrico

3Helpful

4789Views

7Replies

Two CPE210s can't connect well

While waiting for Comcast to connect our house, I'm trying to piggy-back off our neighbor's wi-fi. He kindly let me install a CPE210 configured as an access point on his garage, and I've installed a s

Highlighted Thread

By 88inall · Latest post 2021-09-23 22:33:59 by Sevenyeardust

15Helpful

3403Views

22Replies

Need help choosing CPE for large parking lot

I need to install 2 cameras on each light pole and they will conned to the light pole near the NVR. Please help me choose the right CPEs and number of them. I have used Ubiquiti but Im new to TPLink.

By vivetech · Latest post 3 hours ago by vivetech

0Helpful

22Views

2Replies

2x CPE210 setup regular ping spikes 1500+ms

Hello, I problems with very high ping spikes on my CPE210 setup between 2 houses. The setup is as follows: Fiber modem -> Deco M5 (router for network house 1) -> CPE210 house 1 -> CPE210 house 2 -> D-

Outdoor Wi-Fi Solution

By WilliamG · Latest post 6 hours ago by WilliamG

0Helpful

24Views

2Replies

Low performance on wireless bridge with two CPE710 (AP + Client)

Hi all, after configuring two CPE710 (AP + Client) 200 meters apart, I am experiencing low performance. The devices are matched to 866Mbps RX/TX Rate and are connected to Full-Duplex gigabit ethernet.

Outdoor Wi-Fi Solution

By francesc1 · Latest post 13 hours ago by RickJamesBish

0Helpful

33Views

1Replies

CPE210 AP to two Clients

Hi! I am having a hard time connecting with technical support and looking to see if it's possible to connect two CPE210 to one CPE210 AP. I am currently using Client Mode for the two CPE210s, but not

Outdoor Wi-Fi SolutionPharos ControlRepeater/Bridge Mode

By fancyfaxon · Latest post 19 hours ago by Somnus

0Helpful

23Views

1Replies

N300/CPE510 Beeping twice every minute

Hello, Just noticed one of my CPE510's is beeping twice/2x every minute or so. Both appear to be functioning normally. Both are in AP mode. I found nothing via searches so thought I would try here. Th

By Heimerize · Latest post Yesterday by Somnus

0Helpful

13Views

1Replies

Using two TP-Link Access Points CPE210 on Verizon 5G router

I'm trying to get two CPE210 Access Points attached to my Verizon 5G router and I'm having a problem. First, I'm using the two CPE210 Access Points (AP) as individual Access points where one points to

By pman2022 · Latest post Sunday by pman2022

0Helpful

186Views

10Replies

CPE210 Point to Point over a wide open field about 163ft-185ft, will 2 CPE210's work ?

Hi all, I have 1 CPE210 and was wondering if I should just buy another one or update to newer AP's? Its a short distance and will just be to access a camera and remote heat/humidity sensors in my beeh

By HackerJoe · Latest post Saturday by RickJamesBish

0Helpful

32Views

1Replies