Business Community > Switches > SFP/SFP+ compatibility [T1700G]
< Switches

SFP/SFP+ compatibility [T1700G]

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

SFP/SFP+ compatibility [T1700G]

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
SFP/SFP+ compatibility [T1700G]
SFP/SFP+ compatibility [T1700G]
2017-09-18 14:49:14
Model : T1700G-28TQ

Hardware Version :

Firmware Version :

ISP :

Hi !

I am planning to buy some TP-Link T1700G, which have 4 SFP+ ports.
To interconnect these T1700, I naturally will use a GBIC, which is designed for SFP+, due to to higher transmission rate.
But at the ends, I have SG3209 und SG3216 switches, which both have normal SFP ports (no 'plus').
For this lower bandwidth, COULD I use a GBIC of type TL-SM311LM inside the T1700G??
GBICs are not that cheap and I have several TL-SM311LM already, which could be used at one end of the fiber line.
TL-SM311LM are not mentioned in the spec of the T1700G.

Thanks anyway,
Manfred
  0      
 
  0      
 
#1
Options
4 Reply
Re:SFP/SFP+ compatibility [T1700G]
2017-09-19 08:03:23
Generally, 1000BASE-X SFPs should work in a SFP+ port. Since SFP+ GBICs can't work with 1000BASE-X SFP GBICs on the other side of the fiber, the T1700G's SFP+ port must support SFP GBICs, too, since it's data sheet mentions the 1000BASE-X standard explicitly (under "cables").
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#2
Options
Re:SFP/SFP+ compatibility [T1700G]
2017-11-23 16:09:13

mabra wrote

Model : T1700G-28TQ

Hardware Version :

Firmware Version :

ISP :

Hi !

I am planning to buy some TP-Link T1700G, which have 4 SFP+ ports.
To interconnect these T1700, I naturally will use a GBIC, which is designed for SFP+, due to to higher transmission rate.
But at the ends, I have SG3209 und SG3216 switches, which both have normal SFP ports (no 'plus').
For this lower bandwidth, COULD I use a GBIC of type TL-SM311LM inside the T1700G??
GBICs are not that cheap and I have several TL-SM311LM already, which could be used at one end of the fiber line.
TL-SM311LM are not mentioned in the spec of the T1700G.

Thanks anyway,
Manfred


You can check these information from tp-link website
http://static.tp-link.com/JetStream%20-%20FAQ_Hardware.pdf?configurationId=22931

For T1700G-28TQ/T1700X-16TS, the SFP+ port supports 1Gbps. The premise is to set the speed mode as 1000M for the SFP+ port.
  0  
  0  
#3
Options
Re:SFP/SFP+ compatibility [T1700G]
2017-12-03 01:54:32
On a related note, do the SFP ports on TP-Link switches support 1000Base-T Copper?

For instance, a module like the one shown here?
http://us.dlink.com/products/business-solutions/1000base-t-copper-sfp-transceiver/
  0  
  0  
#4
Options
Re:SFP/SFP+ compatibility [T1700G]
2018-01-08 10:20:42

bobbybc wrote

On a related note, do the SFP ports on TP-Link switches support 1000Base-T Copper?

For instance, a module like the one shown here?
http://us.dlink.com/products/business-solutions/1000base-t-copper-sfp-transceiver/


I have not did the test in the past, so I do not know the result. You can do the test:)
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 2812

Replies: 4

Related Articles
SFP
211 0
SFP+ issues linking to SFP device
389 0
Use 1 GIg SFP with SFP+ port
71 0
MC220L temperature SFP
947 1
SFP patch cable
457 0
SFP+ WAN1 Configuration error
98 0
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.