Business Community > Switches > Multi Vlan & Inter Vlan- Help me
< Switches

Multi Vlan & Inter Vlan- Help me

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Multi Vlan & Inter Vlan- Help me

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Multi Vlan & Inter Vlan- Help me
Multi Vlan & Inter Vlan- Help me
2018-05-23 19:42:29
Model :

Hardware Version :

Firmware Version :

ISP :

Hi I recently purchased and installed a system as follows:
n. 14 Access Point Cap300
n. 1 Access Point Cap300 Outdoor
n. 1 Ac50 Controller
n. 1 POE SWITCH T2600G-28MPS

This wi-fi network is connected to a router provided by the connection provider. His address as a gateway is 192.168.0.254. On it I can not intervene in any way.

I wanted to configure the access points, controllers and switches in order to have VLAN1 (10.10.10.1-255.255.255.0 GW 10.10.10.1), VLAN2 (10.10.20.1-255.255.255.0 GW 10.10.20.1), VLAN3 (10.10.30.1-255.255).

Manage access point DHCP through the AC50 controller and users' Dhcp via SWITCH T2600G-28MPS. According to the various guides I can configure everything but I can not make the routing from the various gateways (10.10.10.1-10.10.20.1-10.10.30.1) to the gateway (192.168.0.254) and I think the problem is in the T2600G-28MPS

My question is simple, is it possible that T2600G-28MPS (v3) does not do multivlan routing?
  0      
 
  0      
 
#1
Options
3 Reply
Re:Multi Vlan & Inter Vlan- Help me
2018-05-25 14:56:32
As I know, T2600G-28MPS should support multivlan routing. Do you mean that the switch has three VLAN and you have set up the IP address for these VLAN? Maybe you can set up the static routing on the switch to forward the data to 192.168.0.254. And set up the static routing on the router to let the data can be back and set up the multi-nets NAT.
  0  
  0  
#2
Options
Re:Multi Vlan & Inter Vlan- Help me
2018-05-25 18:55:09
The exact configuration is as follows:

SWITCH DOORS 1-3-5-7-9-11-13-15 - VLAN2 10.10.20.1-255.255.255.0 GW 10.10.20.1

SWITCH DOORS 2-4-6-8-10-12-14-17 VLAN3 10.10.30.1-255.255.255.0 GW 10.10.30.1

SWITCH DOORS 18-19-20-21-22-23 VLAN4 10.10.10.1-255.255.255.0 GW 10.10.10.1

DOOR SWITCH 24 VLAN1
192.168.0.252 GW 192.168.0.254

static routing 0.0.0.0 0.0.0.0 192.168.0.254

In port 15, 17, 23 I connected the respective ports of AC50 configuring him with the same three vlan

The access points take the addresses of each vlan subnet in dhcp assigned by the AC50 controller

Computers and smartphones take their addresses from the second vlan dhcp assigned by the switch and have their respective gateway (10.10.10.1)

The cable going to the router at the address 192.168.0.254 is connected to port 24.

All next hope are aimed at 192.168.0.254

The individual networks all arrive at 192.168.0.252 but do not go further. Internal internal dhcp and routing services work because I trace packets up to 192.168.0.252
  0  
  0  
#3
Options
Re:Multi Vlan & Inter Vlan- Help me
2018-06-15 11:05:12
There are two FAQ may be helpful.
https://www.tp-link.com/en/faq-1348.html
https://www.tp-link.com/en/faq-1344.html

I think you also need to configure the VLAN interface for VLAN2/3/4.
And if you want the CAP can access internet, you also need to set up the static routing on the router to let the data can be back and set up the multi-nets NAT.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 2409

Replies: 3

About Us
Press
Copyright © TP-Link Corporation Limited. All rights reserved.