configure TL-WA5210G with an Apple Airport Extreme

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

configure TL-WA5210G with an Apple Airport Extreme

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
configure TL-WA5210G with an Apple Airport Extreme
configure TL-WA5210G with an Apple Airport Extreme
2013-01-30 11:54:00
Region : UnitedStates

Model : TL-WA5210G

Hardware Version : V2

Firmware Version :

ISP :


I just purchased the TL-WA5210G (with the Omni-directional Antenna (TL-ANT2415D)) to extend the outdoor coverage of my wifi across my 148 acre property. I am using Cat5E outdoor wiring to connect the TL-WA5210G Access Point about 200 feet back to the house where it connects to the following hardware: TP-Link PoE Injector to Apple AirPort Extreme to Exede (SurfBeam 2) Satellite Internet modem.

I am able to plug the Access Point directly into my laptop and access the configuration page, however, I'm not clear which configuration I should choose. Ideally I'd like to have the AP just act as a relay back to the Apple Airport Extreme via the Cat5e cable which is also used as PoE. So in effect, the TP-Link AP relays the SSID as well as the authentication of the Apple Airport Extreme. However, it appears that if I choose Access Point configuration, the AP will only communicate wirelessly back to the Apple Airport Extreme inside the house.

Thoughts on best way to configure the TL-WA5210G?
  0      
  0      
#1
Options
6 Reply
Re:configure TL-WA5210G with an Apple Airport Extreme
2013-01-30 15:13:49
It seems that you want to extend the wifi signal of your root router ?
So you can consider to set it up as a repeater.
The following guide may help you:
http://www.tp-link.com/en/article/?faqid=442
http://www.tp-link.com/en/article/?id=348
  0  
  0  
#2
Options
Re:configure TL-WA5210G with an Apple Airport Extreme
2013-05-04 23:36:18
I don't want to "extend: the wifi. I ran a Cat5 cable about 130 feet from the Airport Express LAN port to a pole just outside my cabin. I want the TP-Link to connect to my network via the LAN and extend my network across my 150 acres via WiFi (I've also purchased the TP-Link Omni directional antenna TL-ANT2415D).

After trying a few of the different options, I finally just set it up as an Access Point. It works when I connect it to my LAN using a 3 foot Cat5 cable inside the cabin. However, I bought it for outside. I disconnect the 3 foot cable and take it outside to the location where I've run about 130 feet of Cat5 cable. I plug it in and all lights (Power and Wireless Signal Strength) light up except the LAN. I don't believe the Cat5 cable is the problem because I tested it with a line tester and I'm currently running a Foscam FI8905E PoE camera from the same 130 foot Cat5 cable and it works perfectly. However, the TP-Link does not work on it.

Any thoughts on what I can do to troubleshoot this issue?
  0  
  0  
#3
Options
Re:configure TL-WA5210G with an Apple Airport Extreme
2013-05-05 01:17:49
  0  
  0  
#4
Options
Re:configure TL-WA5210G with an Apple Airport Extreme
2013-05-06 22:18:45
Am I reading that thread correctly? The Cat5 cable I have installed, which runs other PoE devices just fine, won't work on the TP-Link because it is 'non-branded'? So what brand does it have to be?
  0  
  0  
#5
Options
Re:configure TL-WA5210G with an Apple Airport Extreme
2013-06-12 05:12:59
can someone provide the recommended cat5 cable so I can run my TP-Link TL-WA5210G with Power over Ethernet?
  0  
  0  
#6
Options
Re:configure TL-WA5210G with an Apple Airport Extreme
2013-06-13 19:57:09
RedTailHawk you started this post on 01-30-2013 02:54 and posted again 06-11-2013 21:12 so you have not solved your issue, so strange you have not apply your RMA (Return merchandise authorization) TP-LINK has a 2 year guarantee and its clear you have a bad POE, cant buy a new one, they change all the 5210, to get your RMA you have to talk to 01800 from TP-LINK in your country, once you get your RMA number then you take it to your dealer, and takes about 30 days.
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1085

Replies: 6