Can`t factory reset using USB cable

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Can`t factory reset using USB cable

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Can`t factory reset using USB cable
Can`t factory reset using USB cable
2021-09-06 01:43:31
Model: TL-SG3428MP  
Hardware Version: V1
Firmware Version:

Hi,

 

     I am trying to factory reset a TL-SG3428MP switch using the USB cable. The switch has been previously adopted by an OC200 controller that has been reseted and thus I don`t know its password nor username. I followed the reset instructions found on https://www.tp-link.com/en/support/faq/3146/ , but the switch refuses to enter bootutil. I also tried to press CTRL+B instead of random keystrokes (as suggested on its manual to no avail). 

 

     Could anyone give me further advice on how to reset it?

 

     Thank you

 

  0      
  0      
#1
Options
9 Reply
Re:Can`t factory reset using USB cable
2021-09-06 03:13:44 - last edited 2021-09-06 03:15:27

@GRALVES 

 

Hey,

 

When you power on the switch, did you keep click the keyboard? If no, the switch will enter autoboot process, and you will fail to enter the BootUtil menu.

 

BTW, if the switch refuses to enter BootUtil menu, what did the screen show? Any picture you can provide?

  0  
  0  
#2
Options
Re:Can`t factory reset using USB cable
2021-09-06 03:24:29 - last edited 2021-09-06 03:30:32

@Somnus I tried:

  1) Hitting a key only once

  2) Hitting random keys 

  3) Hitting random keys + ENTER

  4) Hitting CTRL+B several times

 

  At all the times, after the countdown,  I get the following:

 

 

Starting kernel ...

#2006-01-01 08:00:41,[Link]/5/Gi1/0/23 changed state to up.
#2006-01-01 08:00:41,[NETIF]/5/Line protocol on Interface VLAN1, changed state to up.
#2006-01-01 08:00:42,[Link]/5/Gi1/0/21 changed state to up.
#2006-01-01 08:00:42,[ARP]/3/IP address conflict on interface VLAN1 for IP address 0.0.0.0. Conflicting host MAC address is 78:24:af:bd:72:99.
#2006-01-01 08:00:43,[ARP]/3/IP address conflict on interface VLAN1 for IP address 0.0.0.0. Conflicting host MAC address is 78:24:af:bd:72:99.

***************** User Access Login ********************

User:

 

 

  0  
  0  
#3
Options
Re:Can`t factory reset using USB cable
2021-09-06 03:34:17

@GRALVES 

 

The screenshot shows you have IP conflict. What's your topology? And what is the conflicting MAC address for?

  0  
  0  
#4
Options
Re:Can`t factory reset using USB cable
2021-09-06 03:54:33
Hi, the conflicting MAC is from my workstation - I think the IP conflict is because the workstation is configured in promiscuous mode for debbuging purposes. On my current setup I have my router (ER7206) connected to port 23 and my workstation to port 21. All other ports are disconnected.
  0  
  0  
#5
Options
Re:Can`t factory reset using USB cable
2021-09-06 07:12:54
Hi, you should disconnect the router as well. The default IP of the router is also 192.168.0.1, so it will conflict with the switch.
  0  
  0  
#6
Options
Re:Can`t factory reset using USB cable
2021-09-06 13:38:29

@Somnus 

 

I disconnected everything from the switch but the USB cable, had the same issue as before, but without the IP errors:

 

 

  0  
  0  
#7
Options
Re:Can`t factory reset using USB cable
2021-09-07 18:25:38

Couldn`t make it work throught USB, I ordered a cheap USB-RS232 cable and connected throught the RS232 console. Using this I was able to reset the switch on my first try. 

 

  0  
  0  
#8
Options
Re:Can`t factory reset using USB cable
2021-09-08 09:16:26 - last edited 2021-09-08 09:24:04

@GRALVES 

 

So it's the issue of the USB cable? I just saw the note in the FAQ that Micro USB cable is more difficult to enter the BootUtil than RJ45 console cable and USB-to-RS232 cable.

  0  
  0  
#9
Options
Re:Can`t factory reset using USB cable
2021-09-08 16:43:17

@Somnus 

 

I was able to reset it on the first try using the RS232 cable. I think the problem is not on the cable but on the USB port on the switch. If I understood how it was implemented, it looks like the USB-serial IC on the switch only gets powered once the switch is on. There is always a small delay for the workstation to map and load the USB device drive.

 

I think this delay + the time for the IC to power on is greater than the time the switch allows for a key-press to enter the Bootutil. Perhaps it could be solved if tp-link released a firmware with a longer delay - but it needs to be tested. Another option would be, in a latter HW revision, that the USB IC be powered by the USB cable and not by the computer itself. 

  0  
  0  
#10
Options

Information

Helpful: 0

Views: 1178

Replies: 9