TL-SG2428P v4.0 upgrade issues with LACP after V4.06

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-SG2428P v4.0 upgrade issues with LACP after V4.06

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-SG2428P v4.0 upgrade issues with LACP after V4.06
TL-SG2428P v4.0 upgrade issues with LACP after V4.06
2023-12-27 08:23:34
Model: TL-SG2428P  
Hardware Version: V4
Firmware Version: 4.05

After upgrading from V4.05 to 4.06 the switch doesn't work with my 2 LACP anymore. I re-created a 4 port and 2 port LACP configuration but this didn't help. I reversed the firmware back to V4.05 and all was fine again.

  0      
  0      
#1
Options
3 Reply
Re:TL-SG2428P v4.0 upgrade issues with LACP after V4.06
2023-12-28 06:18:08 - last edited 2023-12-28 06:18:17

Hi @JayinNZ,

 

Thank you so much for taking the time to report the issue to our community!

1. What's the physical connection (current topology) of your all devices? (You can draw a diagram of Network Topology simply if you don't mind.)

2. What is the firmware version of your controller?

3. Could you share how you set the LACP?

 

JayinNZ wrote

After upgrading from V4.05 to 4.06 the switch doesn't work with my 2 LACP anymore.

 

4. Please elaborate on the problem phenomenon " doesn't work with my 2 LACP anymore", and how you test.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:TL-SG2428P v4.0 upgrade issues with LACP after V4.06
2023-12-28 06:59:36

  @Hank21 

Here we go with the details:

Both LAGs 1&2 are setup in Omada as aggregating and active LACP:

 

both server run debian and are setup in network bond like:

bond0

After upgrading from V4.05 to V4.06 the LAG/Bond doesn't send/receive any data, it's just dead. Didn't help to re-create the LAG's on Switch. I use

OC200 2.0

Firmware Version

2.11.3 Build 20230906 Rel.36272

 

after reverting everything works as before.

 

Hank21 wrote

Hi @JayinNZ,

 

Thank you so much for taking the time to report the issue to our community!

1. What's the physical connection (current topology) of your all devices? (You can draw a diagram of Network Topology simply if you don't mind.)

2. What is the firmware version of your controller?

3. Could you share how you set the LACP?

 

JayinNZ wrote

After upgrading from V4.05 to 4.06 the switch doesn't work with my 2 LACP anymore.

 

4. Please elaborate on the problem phenomenon " doesn't work with my 2 LACP anymore", and how you test.

 

  0  
  0  
#3
Options
Re:TL-SG2428P v4.0 upgrade issues with LACP after V4.06
2023-12-29 08:24:01

Hi @JayinNZ

 

To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID231254259, please check your email box and ensure the support email is well received. Thanks!

Once the issue is addressed or resolved, welcome to update this topic thread with your solution to help others who may encounter the same issue as you did.

Many thanks for your great cooperation and patience!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options