Business Community > Switches > T1500G-10MPS is loosing Static IP-Address after Power-Cycle
< Switches

T1500G-10MPS is loosing Static IP-Address after Power-Cycle

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

T1500G-10MPS is loosing Static IP-Address after Power-Cycle

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
T1500G-10MPS is loosing Static IP-Address after Power-Cycle
T1500G-10MPS is loosing Static IP-Address after Power-Cycle
2017-06-04 20:02:25
Model : T1500G-10MPS

Hardware Version : 1.0

Firmware Version : 1.0.0 Build 20160913 Rel.52092(s)

ISP :

I configured a T1500G-10MPS System IP to a static IP-Address and saved the config.
After the IP-Address is changed, everything works perfectly fine until the Switch is powered cyled.
I saved the changed config using the Web-Interface and also using the CLI (there is no difference in the result).

All other changes that were made (VLANS, Port-Config, DeviceName, Location & Description) are saved and
still OK after the switch was powered off and on again.

Only the static-IP Address is gone and the switch boots up with the default (192.168.0.1) IP-Address.

Current workaround is to set the Switch IP-Address-Mode to DHCP and assign a reserved IP-Address which works
(even when the switch is power-cycled). After reboot the Switch still shows DHCP but I want to set a static-IP and
I think the switch should remeber this address even if power is gone for 1 Minute.

Any Idea?
  0      
 
  0      
 
#1
Options
3 Reply
BUG T1500G-10MPS / cannot set gateway address / looses ip address
2017-06-27 20:09:29
I have the same problem.
But only if I enter a default gateway via Webfrontend. The switch generates a configuration with e.g.

interface VLAN 1
ip address 192.168.2.100 255.255.255.0 192.168.2.1

Which is incorrect according to the documentation (this should be "ip address 192.168.2.100 255.255.255.0 gateway 192.168.2.1"). Nevertheless, none of the commands work if you enter them on the command line (Error "too many parameters").

If you reset / reboot the switch with this config written the ip address is not set because - I think - the switch cannot interprete the command.

I found no way to set a default gateway on a T1500G-10MPS :( :( (even with ip settings from DHCP the switch is not reachable over the default gateway which is configured in the dhcp options)
  0  
  0  
#2
Options
Re:T1500G-10MPS is loosing Static IP-Address after Power-Cycle
2017-10-29 07:21:45
I know that this is an old topic, but I'm looking to get this exact same switch. Do you think the latest firmware, 170607, fixes this issue? It says "1. Fixed the Bug that can't display the System IP page under certain circumstance"

http://www.tp-link.com/us/download/T1500G-10MPS.html#Firmware
  0  
  0  
#3
Options
Re:T1500G-10MPS is loosing Static IP-Address after Power-Cycle
2017-12-04 18:45:26
I can confirm that applying the 170607 firmware fixes this issue of loosing IP address and some other setting e.g. time zone.
BUT Be Aware :- my 1st attempt at that effectively left the switch useless, the upgrade didn't take effect and POE no longer available on any of the ports, so now useless.
I got a slightly newer replacement from Amazon, had the same issues, but this time was fixed by the firmware upgrade.
1st unit Serial Number: 21746........
2nd unit Serial Number: 21764.......
This will be far too late a reply for bobbybc, but thought worth posting in case others search for the problem...
  1  
  1  
#4
Options

Information

Helpful: 0

Views: 1221

Replies: 3

About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.