TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-07-27 05:46:07
Model :

Hardware Version :

Firmware Version :

ISP :

Dear forum readers / writers,

I'm currently struggling with a strange error message popping up when trying to set up 802.11q VLAN: "Amount of VLAN is full" The error message occurs when trying to simply configure a VLAN using VLAN-ID 100, one tagged and two untagged ports. Some tests have shown that the error message neither depends on amount of ports in VLAN nor VLAN-ID or VLAN name.

Just to provide you with an overview of what I'm trying to achieve:

Used enviroment
Switch TL-SG1016PE
AP EAP245
Router FritzBox 7590 (doesn't support VLAN)

Goal
AP provides "main WLAN" without VLAN-ID
[*]AP provides "guest WLAN" with VLAN-ID 100
[*]AP connects to switch's port 5
[*]Switch provides guest WLAN untagged to port 11 (guest WLAN uplink to FritzBox)
[*]Switch provides main WLAN to port 10 (all other traffic uplink to FritzBox)

Did anybody already faced that message? And if so: What am I doing wrong?

Thanks in advance and best regards,
Stephan
  0      
  0      
#1
Options
15 Reply
Same Problem The amount of VLAN is full
2017-07-28 15:01:26
Hello,

i have the same Problem.

When i enter a vlan i got the message : The amount of VLAN is full:

Firmeware of TL-SG1016DE 3.0 is 1.0.1 Build 20170530

Any Idee ?

Thanks Bernd
  0  
  0  
#2
Options
System Reset
2017-08-17 12:47:39
I was having the same issue after a fresh firmware install (Hardware: TL-SG1016DE 3.0, Firmware: 1.0.1 Build 20170530 Rel.39380). I did a system reset and re-enabled 802.1Q VLAN option - that resolved the issue for me. Before the system reset, with 802.1Q VLAN enabled I noticed that the Default_VLAN wasn't listed.
  1  
  1  
#3
Options
Re:TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-08-17 19:57:23
Hello.... just wanted to let the group know I'm experiencing the same issue on a new TL-SG1024DE
An answer to this question would be much appreciated.

Thanks,
Joe
  0  
  0  
#4
Options
Re:TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-08-18 20:35:36
System reset fixed my 802.1Q VLAN too... Default_VLAN was not visible before reset as Davidj2 said...
  0  
  0  
#5
Options
Re:TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-08-21 17:40:54
I think you updated the firmware then met this issue.You only need reset switch , this issue will be solved.
  0  
  0  
#6
Options
Re:TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-08-22 02:00:38
Just to be clear... my situation was with a new switch ( TL-SG1024DE)... not after updating the firmware. The installed firmware was up to date on my new switch... but still required the reset.
  0  
  0  
#7
Options
Re:TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-08-25 09:15:07

AntiJoe wrote

Just to be clear... my situation was with a new switch ( TL-SG1024DE)... not after updating the firmware. The installed firmware was up to date on my new switch... but still required the reset.

Strange, I have a TL-SG1024DE too. A new one of V3, it work just fine to set VLAN. The problem will happen only after I upgrade the firmware to 170530. What's your firmware version?
  0  
  0  
#8
Options
Re:TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-08-30 21:07:25
(Almost the) same problem here - German retail version of the switch.

When I enter a VLAN definition, the answer from the switch is always "failed".

I've tried everything what the support people told me: different browser, remove antivirus software (the switch just generates a GET command and doesn't need any additional software), resetting the switch this way or another. I even exchanged the switch, and went through the same problems.

Now it seems that it is a bug in the firmware. OK, I will wait a few weeks and see if a new firmware is available.

Otherwise the TP-Link hardware is really fine, no questions asked.
  0  
  0  
#9
Options
Re:TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-08-31 10:07:58

Georg wrote

(Almost the) same problem here - German retail version of the switch.

When I enter a VLAN definition, the answer from the switch is always "failed".

I've tried everything what the support people told me: different browser, remove antivirus software (the switch just generates a GET command and doesn't need any additional software), resetting the switch this way or another. I even exchanged the switch, and went through the same problems.

Now it seems that it is a bug in the firmware. OK, I will wait a few weeks and see if a new firmware is available.

Otherwise the TP-Link hardware is really fine, no questions asked.


Hey dude, I think this problem can be solved by reset the device after upgrading to the new firmware. As I can see, some people have the same issue and get recovered. Or maybe we are not the same issue?
We were talking about the 170530 firmware.
  0  
  0  
#10
Options
Re:TL-SG1016PE (Ver. 39357) shows "amount of VLAN is full"
2017-08-31 23:47:10
Hi, Hibixa -


I tried resetting and new configuration a few times in the past, with not effect.

I have re-installed the installed firmware (170530), powered the switch off and on, did a reset and - much to my surprise - I was able to define my VLAN settings.

Thanks for your feedback which gave me the drive to try it again.
  0  
  0  
#11
Options

Information

Helpful: 0

Views: 3223

Replies: 15