Business Community > Switches > How to get the MAC address table from a SG3216 switch via SNMP?
< Switches

How to get the MAC address table from a SG3216 switch via SNMP?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to get the MAC address table from a SG3216 switch via SNMP?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to get the MAC address table from a SG3216 switch via SNMP?
How to get the MAC address table from a SG3216 switch via SNMP?
2017-08-12 11:57:45
Model :

Hardware Version :

Firmware Version :

ISP :

Hello !

I have some SG3109 switchs which are monitoed to its known MAC addresses. This works, just as an example, using linux snmpwalk command, like this:
>snmpwalk -v 2c -c public 192.168.1.2 .1.3.6.1.2.1.17.4.3
and one can even pick the mac addresses directly.

Astounding for me, querying the bigger switches I have in use (SG3216) , which I bought later (some time after the SG3109) fails!
Does that mean, the snmp bridge MIB is not supported on this switch?
What so about the TL1600 - which is probably my next candidate.

But from a security perspective, a LAN has to be watched for foreign addresses and so I hasitate to buy a new switch from
TP-LINK, because I am unable to find the reason:
- not supported ??
- how to configure the switch to access this OID: .1.3.6.1.2.1.17.4.3

Thanks anyway,
Manfred

Note: There are several "standards" to this, see: http://cric.grenoble.cnrs.fr/Administrateurs/Outils/MIBS/?oid=1.3.6.1.2.1.4.22
- IP-MIB (CISCO)
- RFC1213-MIB (DELL)
- IP-MIB (DELL)
- IP-MIB (ietf)
- RFC1213-MIB (ietf)
  0      
 
  0      
 
#1
Options
4 Reply
Re:How to get the MAC address table from a SG3216 switch via SNMP?
2017-09-11 09:50:15
hey dude, I think you are using the wrong oid value, I suggest you go to their official website to download the MIB files, the MIB files can tell you the correct OIDs of the nodes.
  0  
  0  
#2
Options
Re:How to get the MAC address table from a SG3216 switch via SNMP?
2017-09-18 14:35:53
Hi,

and thanks for your reply.

ChimB wrote

hey dude, I think you are using the wrong oid value, I suggest you go to their official website to download the MIB files, the MIB files can tell you the correct OIDs of the nodes.


I do not believe that. If you are doing a snmp-walk, you'll find usually all presented value. THEIR MIB would not be neccessary
for this and this works with all switches, ehich provide the mac-address-table, at least, all of these, I've seen so far.
If this is not true, let me know!
The MIB is only valuable, if you have a full-fledged management system

And: If someone claims to be manageble, why does he not implement existing standards?

Regards,
Manfred
  0  
  0  
#3
Options
Re:How to get the MAC address table from a SG3216 switch via SNMP?
2017-09-19 09:44:41
hey dude, I think you can test this in an easiest way, just run the wireshark, then use snmp to get this OID value, then look for the packets captured in the wireshark, and you will know if this OID really exists or not.:)
  0  
  0  
#4
Options
Re:How to get the MAC address table from a SG3216 switch via SNMP?
2017-09-19 09:45:24
hey dude, I think you can test this in an easiest way, just run the wireshark, then use snmp to get this OID value, then look for the packets captured in the wireshark, and you will know if this OID really exists or not.:)

mabra wrote

Hi,

and thanks for your reply.



I do not believe that. If you are doing a snmp-walk, you'll find usually all presented value. THEIR MIB would not be neccessary
for this and this works with all switches, ehich provide the mac-address-table, at least, all of these, I've seen so far.
If this is not true, let me know!
The MIB is only valuable, if you have a full-fledged management system

And: If someone claims to be manageble, why does he not implement existing standards?

Regards,
Manfred
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 2445

Replies: 4

Related Articles
MAC address Table in TL-SG1428PE
191 0
Omada: how to view switch MAC address to port table? (aka CAM table)
2403 0
 MAC address table present anywhere in SNMP MIB?
1495 0
 MAC table for SG108E 2.0
2737 0
MAC address filter per device
2997 0
 Only MAC Address
354 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.