EAP-110 Outdoor AP not retaining configuration on auto nightly reboot
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.EAP-110 Outdoor AP not retaining configuration on auto nightly reboot
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
We are currently using 7 EAP-115 and 1 EAP-110 outdoor APs in our apartment society gates for Wifi Access to MyGate Tablets. Recently we have observed a niggling problem with the EAP-110 outdoor unit that after reboot it does not ratain has its configuration and has to be manually adopted and WLAN group reconfigured. Here is the controller log:
(1) All our APs are configured to restart at 4:00 am in the morning everyday,
(2) The Outdoor AP (70-4F-57-74-40-B2) also follows this routine but when it restarts it does not come back to its configured state like other indoor APs (EAP-115s with macs ending with F2, F8, 4B octets in picture), despite controller being kept on. It just goes into Pending state with the correct IP and connectivity (layer 3 networking sems just fine because it is able to get on the network)..
(3) To bring out of its pending state, we have to
(a) manually adopt the AP
(b) assign it to the correct site and configure the WLAN Group on the AP again
(4) After this the problem goes away for a day or 2 or 3, till it reappears.
This has started happening after we switched from Auranet Controller to latest Omada Controller (now running 3.0.5) OR one of the Omada Controller software upgrades. It was defintely not observed for 6-8 months of operation with the Auranet Controller
Any pointers to debug further or resolve will be appreciated.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi,
I ran the system without controller for 5-6 days and nights. The problem does not repeat. It only happens every 3rd or 4th reboot in our setup if and only if the *controller is running even with updated firmware.
However, with the controller application closed, I can't collect statistics, monitor system, see logs. etc ( a handicapped system), plus their is a latent need of portal and voucher authentication in very near future. so not practical in long term. I am just hoping that atleast even without the controller application running the APs are restarting as scheduled using their local configuration caches.
Also i noticed that on US site, their is a firmware EAP110-Outdoor(EU)_V1_1.2.0 Build 20180418 released on 2018-04-28 available on global site (I normally use the Tp Link India site based on my localization). This seems to be a version ahead of the beta firmware suggested bby Jonas. Does it have all the changes of the beta ?
Regards
Suman @ APRC Telecom WG
- Copy Link
- Report Inappropriate Content
Day 5 now without losing the EAPs association to the Controller v2.7 whith scheduled daily reboots. I have switched off scheduled reboots now, since we usually let our customer's EAPs run for long periods without any scheduled reboots. As I wrote, un-scheduled nightly reboots we observed earlier on our EAP110-Outdoor APs don't happen anymore since update with the beta version.
APRC-P3-Tel wrote
Also i noticed that on US site, their is a firmware EAP110-Outdoor(EU)_V1_1.2.0 Build 20180418 released on 2018-04-28 available on global site (I normally use the Tp Link India site based on my localization). This seems to be a version ahead of the beta firmware suggested bby Jonas.
I think that's a wrong assumption.
First, static.tp-link.com is not a localized US site, but a central site for static files linked to by all country-specific TP-Link sites. Firmware links on EU, US and any other sites always point to static.tp-link.com.
Second, the April 2018 firmware version is what I did run before updating with @jonas' beta version. Both versions share the same version number (1.2.0), but the beta version is dated 2018-08-08, while the official firmware is from 2018-04-28, thus the beta is definitely the newer one. Final official version incorporating beta version changes will be probably 1.3.0 or something if being published.
Third, you always should use country-specific firmware links found on your local TP-Link site (linking to static.tp-link.com). The EU version probably does no apply to local regulations in India.
- Copy Link
- Report Inappropriate Content
I think that's a wrong assumption.
First, static.tp-link.com is not a localized US site, but a central site for static files linked to by all country-specific TP-Link sites. Firmware links on EU, US and any other sites always point to static.tp-link.com.
Second, the April 2018 firmware version is what I did run before updating with @jonas' beta version. Both versions share the same version number (1.2.0), but the beta version is dated 2018-08-08, while the official firmware is from 2018-04-28, thus the beta is definitely the newer one. Final official version incorporating beta version changes will be probably 1.3.0 or something if being published.
Third, you always should use country-specific firmware links found on your local TP-Link site (linking to static.tp-link.com). The EU version probably does no apply to local regulations in India.
Hi R1D2，
Yes, you are right.
1. static.tp-link.com is where we store the software/firmware of our product. In face, the EU and US version EAP110-Outdoor share same firmware (but the default nation code of the products is different), so it is OK for EU or US version customer to use this beta firmware.
2. We have made the beta firmware in 20180808, so it is newer then the official firmware of EAP110-Outdoorv1, it contain all function of the newest official firmware (20180418)
- Copy Link
- Report Inappropriate Content
The problem seems fully solved for us now with the beta firmware and 2+ weeks of observation. Thanks to Jonas and R2D2 for all the help and suggestions.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 5913
Replies: 14
Voters 0
No one has voted for it yet.