Network past thru EAP 245 V3, issues with ccam frame rate
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.Network past thru EAP 245 V3, issues with ccam frame rate
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello.
What is the built in switch capacity of EAP245 V3 ? (I mean the usage of the second Lan port forwarding the first lan PoE port)
I got issues with surveillance cam (slow frame rate) once I had connected 2 EAP245 into the network.
Here is my topology :
Main Router TL-ER6120 V1 with 2 Switch directly connected on it (TL-SG108PE & TL-SG1024)
2XEAP245 + Dlink Cam + OC200 connected to TL-SG108PE
Cascaded switch TL-SG108 connected to 1 EAP245 on the second port Lan
1 Axis Cam connected with CPL and linked with TL-SG1024
Camera server surveillance connected to TL-SG1024
No issue at all with the axis cam that is linked directly to the TL-SG1024 and got route without past thru network device where is connected EAP245.
Verry low frame rate performance with Dlink cam that is connected to the same switch use by 2 EAP245.
If I disconnect the 2 EAP245 and use other AP from other made (Asus RT-AC66U) with the same topology
I got better frame rate with my Dlink lan cabeled than the Axis with CPL link.
I tried to give best priority port on uplink port of the TL-SG108PE connected to the Router- no success
Tried to disable IGMP Snooping from switch.
Tried to give QOS for the Cam.
nothing fixed the issue.
Is there anny chance to get back my good network performance once i use EAP245 ?
Thank for any advise or helps with this.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Pascal wrote
Pascal wrote
- Lan Ports EAP
OK, If I understand your explain,there is no forwarding limitation speed with Past Thru the Lan port.
Then No agregation possibility ?
and seem to use the old way HUB lan ?
You mean if you do not use the RTSP/RTP protocols and use the MJPEG mode, then the camera if working well.: YES
But if you use H264 mode, then the video of camera has no lags and shows smoothly? NO, the video of the camera goes terrible, losing frame, slow motion, saccaded.
- the Dlink cam is DCS-4701E with latest firmware
with EAP presence:
-video H264 with RTSP/RTP, the stream start well during 1 or two minutes (good frame rate, no saccad) after then video suffer lags and saccad with lost of some frame.even with 7 frames/sec.-video MJPEG, no issues at all, stream is good and no frame lost, got 25frames/sec.
Without EAP presence
the H264 video stream is working well, no saccad, no lost frame and use 15 frames/sec
Also Users complains about no possibility to access internet without raison, the device is connected to the EAP245 and got verry good Wifi signal and less than 3M far from the EAP. They need to switch Off they Wifi and switch it back on tho be able to surf on the web again till the next time they are blocked again.
The Issue seem to be only with the access points that are on the Lan segment connected with the past Thru lan port.
By experience with SONOS, I had disconnect the SONOS to be sure there is not STP issue or loop between the SONOS net and our intranet, but the problems are still there.
I will now put back the OLD Asus RT-AC66U as termination of this lan segment, and put back the Netrgear GS510T in the midle of this segment. The EAP-245 experience is deffinitly not a success, as it is not affect only the Cam frame rate but all internet experience with Wifi devices.
- Copy Link
- Report Inappropriate Content
I finaly purshased the TL-ER6120 V3 (remove the NAT bottleneck issue)
Swap the GS510TP with an TL-GS1016PE. (better Gps switch capacity)
disable WiFi of the SONOS near the EAP (all cabeled now)
will see now if I still got frame rate issue and loosing internet acces.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 3505
Replies: 12
Voters 0
No one has voted for it yet.