EAP 220 Missing from TP-Link Controller (Version: 2.5.4)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP 220 Missing from TP-Link Controller (Version: 2.5.4)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP 220 Missing from TP-Link Controller (Version: 2.5.4)
EAP 220 Missing from TP-Link Controller (Version: 2.5.4)
2020-02-27 01:33:46
Model: EAP220  
Hardware Version: V1
Firmware Version: 2.0.2 Build 20160401 Rel. 65964

Set the channel from auto to manual and then the listed eap220 earlier disappeared from under the 'access point' tab. But the 'client' tab stil showing clients listed under those missing acces point. 

 

Anyone encountered this before and how to bring it back?

 

  0      
  0      
#1
Options
6 Reply
Re:EAP 220 Missing from TP-Link Controller (Version: 2.5.4)
2020-02-27 16:51:31 - last edited 2020-02-27 16:52:37

@theArties, did you select »All« under the »Access Points« tab? Is the EAP220 shown in disconnected or pending state? Or do you say it disappeared completely from all AP lists in the controller?

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#2
Options
Re:EAP 220 Missing from TP-Link Controller (Version: 2.5.4)
2020-02-28 01:51:10

@R1D2 

 

Its selected by default, and yes, click again the 'All' to be sure. 

Guessing this is a layout bug issue; coz when I clicked on either of the sorting button (circled red), it will switch to the other APs.

And note the headers alignment. this is from FF at 100% zoom. 

 

  0  
  0  
#3
Options
Re:EAP 220 Missing from TP-Link Controller (Version: 2.5.4)
2020-02-28 09:22:25

@theArties, what do you mean with »it will switch to the other APs«? If you change the sorting order, the APs appear in another order, but do not disappear.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#4
Options
Re:EAP 220 Missing from TP-Link Controller (Version: 2.5.4)
2020-02-28 10:56:30

@R1D2 Say i have 4 APs- 1,2,3,4

 

When clicked on 'Name/Mac Address', it will show either AP 1, press again AP 2. 

And when clicked on 'TX 2g' or 'TX 5G', it will show either AP 2 or AP 3.

 

Weird right, and it will never show all 4 APs together. 

  0  
  0  
#5
Options
Re:EAP 220 Missing from TP-Link Controller (Version: 2.5.4)
2020-02-28 12:55:05

@theArties, maybe it helps to try another browser; I never experienced such a behavior.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#6
Options
Re:EAP 220 Missing from TP-Link Controller (Version: 2.5.4)
2020-02-29 07:22:17

@theArties 

 

It is truly strange if all APs cannot show up. You can try to reboot the Controller, then check if the problem still exists. 

  0  
  0  
#8
Options

Information

Helpful: 0

Views: 1173

Replies: 6