Business Community > Switches > Trunk Port
< Switches

Trunk Port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Trunk Port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Trunk Port
Trunk Port
2020-08-13 17:54:16 - last edited 2020-08-21 00:42:47
Model: T1600G-28PS(TL-SG2424P)  
Hardware Version: V3
Firmware Version:

Hello,

 

I have pfsense firewall. and I configure 4 VLANs on it. As mentioned below. Also, I have purchased TP-Link T1600G-28PS managed switch. 

=================

VLAN10 >> 10.10.10.0

VLAN 20 >> 10.10.20.0

VLAN30 >> 10.10.30.0

VLAN50 >> 10.0.0.0

=================

 

Question: I have created 4 VLANs on my PFsense and configured DHCP on it (on a single interface). I have connected it to switch. and I want to provide VLAN 10 to all my Management devices. VLAN20 to VMs which is hosted on Management ESXI Node. and VLAN30 & VLAN 50 to wireless clients. But on the switch, I am not able to see the trunk port option, 

 

Is anyone have any idea about it how to configure it on the T1600G-28PS switch?

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Trunk Port-Solution
2020-08-14 03:20:44 - last edited 2020-08-21 00:42:47

Dear @Rishi_J,

 

Question: I have created 4 VLANs on my PFsense and configured DHCP on it (on a single interface). I have connected it to switch. and I want to provide VLAN 10 to all my Management devices. VLAN20 to VMs which is hosted on Management ESXI Node. and VLAN30 & VLAN 50 to wireless clients. But on the switch, I am not able to see the trunk port option, Is anyone have any idea about it how to configure it on the T1600G-28PS switch?

 

 

No, there is no trunk port option on the T1600 switches anymore. But we can simply specify the port as Tagged Ports when adding it to the corresponding VLAN to achieve the Trunk feature. This configuration example for 802.1Q VLAN may help you better.

 

Best regards!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
1 Reply
Re:Trunk Port-Solution
2020-08-14 03:20:44 - last edited 2020-08-21 00:42:47

Dear @Rishi_J,

 

Question: I have created 4 VLANs on my PFsense and configured DHCP on it (on a single interface). I have connected it to switch. and I want to provide VLAN 10 to all my Management devices. VLAN20 to VMs which is hosted on Management ESXI Node. and VLAN30 & VLAN 50 to wireless clients. But on the switch, I am not able to see the trunk port option, Is anyone have any idea about it how to configure it on the T1600G-28PS switch?

 

 

No, there is no trunk port option on the T1600 switches anymore. But we can simply specify the port as Tagged Ports when adding it to the corresponding VLAN to achieve the Trunk feature. This configuration example for 802.1Q VLAN may help you better.

 

Best regards!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options

Information

Helpful: 0

Views: 1499

Replies: 1

Related Articles
How to configure a Trunk Port
299 1
Trunk port on TL-SG2210P and TL-SG3424
518 0
TRUNK PORT
485 0
trunk port
383 0
Adding Trunk Port
905 0
ACL on switch port to deny traffic to local subnet - except to router, and allow internet
2065 0
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.