Business Community > Controllers > WLAN Schedule Enabled But Not Working
< Controllers

WLAN Schedule Enabled But Not Working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

WLAN Schedule Enabled But Not Working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
WLAN Schedule Enabled But Not Working
WLAN Schedule Enabled But Not Working
2020-09-15 04:16:08 - last edited 2020-09-22 01:06:08
Model: EAP245  
Hardware Version: V3
Firmware Version: 2.21.0

I have two SSIDs defined on this controller with a schedule set to 'radio on' within the schedule.  The access points do not turn off the particular SSID no matter what I try.  I've checked the time zone and the controller time to make sure that the time lines up.  I have not tried the 'radio off' inside scheduled hours.  I am using a custom schedule for the timeframes.  Any words of advice?

 

Omada Controller 4.1.5

Running in Linux LXC container with Ubuntu Base

 

Thanks,

 

Nick

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:WLAN Schedule Enabled But Not Working-Solution
2020-09-15 13:47:45 - last edited 2020-09-22 01:06:08

@neuralp 

 

Are you using DST time zone in your region? I assume it's related to the DST issue. The Omada Controller 4.1.5 doesn't support Daylight Saving Time, as per TP link support, it will be added in the next version. 

Recommended Solution
  2  
  2  
#2
Options
3 Reply
Re:WLAN Schedule Enabled But Not Working-Solution
2020-09-15 13:47:45 - last edited 2020-09-22 01:06:08

@neuralp 

 

Are you using DST time zone in your region? I assume it's related to the DST issue. The Omada Controller 4.1.5 doesn't support Daylight Saving Time, as per TP link support, it will be added in the next version. 

Recommended Solution
  2  
  2  
#2
Options
Re:WLAN Schedule Enabled But Not Working
2020-09-16 07:36:42 - last edited 2020-09-16 07:38:23

 

neuralp wrote

Any words of advice?

 

As @Yannie wrote, this might be related to the TZ/DST issue. Try to set the Controller's (not the Site's) timezone to Universal Time Coordinated (UTC) and specify schedule times in UTC, too. If this works, the issue is related to the TZ setting.

༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  2  
  2  
#3
Options
Re:WLAN Schedule Enabled But Not Working
2020-09-22 01:05:36

@R1D2 

 

Thank you both, I do believe that this is a timezone issue.  I have the timezone set to one off of what I normally would to compensate for the lack of DST, and thus I figured the schedule would abilde by it.  I did notice that it does turn off an hour later, so I will just adjust.  Thanks!

  1  
  1  
#4
Options

Information

Helpful: 1

Views: 1677

Replies: 3

Related Articles
 WLAN Schedule not working consistently
826 0
 WLAN Schedule
1716 0
 WLAN or SSID Schedule
567 0
 WLAN Schedule DOES NOT WORK RELIABLY
909 0
 What is the expect behavior for WLAN Schedule?
357 0
 WLAN Schedule in Omada App
258 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.