Access modem behind wan port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Access modem behind wan port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Access modem behind wan port
Access modem behind wan port
2013-02-08 03:52:20 - last edited 2021-08-21 03:18:52
Region : Greece

Model : TL-R480T+

Hardware Version : V5

Firmware Version : 5.0.0 Build 20120307 Rel.58769s

ISP : Wind


Hello....

How can I access the ADSL modem which is connected to a WAN port?

My configuration is:
Router : 192.168.2.1/255.255.255.0
Modem at WAN1: 192.168.0.1
Modem at WAN2: 192.168.1.1

The WAN ports are configured with static IP: 192.168.0.100 and 192.168.1.100
All the computers after the router have IP: 192.168.2.x

Thanks in advance !!!!
  0      
  0      
#1
Options
5 Reply
Re:Access modem behind wan port
2013-02-08 15:28:55 - last edited 2021-08-21 03:18:52
What is the brand of the modem ? and the lan IP of the modem ???
  0  
  0  
#2
Options
Re:Access modem behind wan port
2013-02-08 16:10:34 - last edited 2021-08-21 03:18:52
I have 2 modems SAGEM 1500.
The LAN IP of the modem is 192.168.0.1 at WAN1 and 192.168.1.1 at WAN2.
  0  
  0  
#3
Options
Re:Access modem behind wan port
2013-02-12 23:56:08 - last edited 2021-08-21 03:18:52
Any help will be very acceptable !!!
  0  
  0  
#4
Options
Re:Access modem behind wan port
2013-03-14 03:17:32 - last edited 2021-08-21 03:18:52
If the WAN ports are configured to use static IP addresses then it should be accessible through normal web browser interface, like http://192.168.1.1 for WAN2. Make sure that modem connected to WAN1 have the IP address in the rang 192.168.0.0. You can check this by pinging the modem through the diagnostic utility given in Miantenance > Diagnostic > Ping of the loadbalancer. Select the WAN 1 for pinging Modem1 and give its IP address. Before ping make sure that the modem is on and properly the cable is pluged in and the WAN port have link up status . After ping If the timeout is shown in the results, modem does not have the IP address in the network address space of the WAN interface to which it is connected.
  0  
  0  
#5
Options
Re:Access modem behind wan port
2013-05-01 04:59:33 - last edited 2021-08-21 03:18:52
On my setup :

DSL MODEM 1 on WAN 1:
IP Address: 10.0.1.50
Subnet Mask: 255.255.0.0
Gateway: 10.0.0.1

DSL MODEM 2 on WAN 2:
IP Address: 172.16.1.50
Subnet Mask: 255.255.0.0
Gateway: 172.16.0.1

TL-R480T+ on LAN: 192.168.2.1

I can see any of the devices on each of the gateways IPs
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1665

Replies: 5

Related Articles