Business Community > Pharos Wireless Bridges > CPE210 with Deco P9
< Pharos Wireless Bridges

CPE210 with Deco P9

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

CPE210 with Deco P9

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
CPE210 with Deco P9
CPE210 with Deco P9
2020-11-16 15:16:23
Model: CPE210  
Hardware Version: V3
Firmware Version: 
Hello,
I have already installed many CPE210 in Client mode without any problem.
Now I want to use CPE210 to connect a IPcam to Deco P9.
But impossible

 

test:

WWW <=ok=> InternetBox <=ok=> CPE210<=ok=> IPcam

WWW <=ok=> InternetBox <=ok=> Deco P9 <=ko???=> CPE210<=ok=> IPcam

 

Firmwares:

DecoP9 = 1.1.2 Build 20200918 Rel. 74476

CPE210 V3.2EU = 2.2.2 Build 20200612 Rel. 38101 (4555)

 

Thanks for your help

 

  0      
 
  0      
 
#1
Options
6 Reply
Re:CPE210 with Deco P9
2020-11-20 01:26:59

Dear @DK26,

 

Now I want to use CPE210 to connect a IPcam to Deco P9. But impossible

test:

WWW <=ok=> InternetBox <=ok=> CPE210<=ok=> IPcam

WWW <=ok=> InternetBox <=ok=> Deco P9 <=ko???=> CPE210<=ok=> IPcam

 

So you are trying to connect the CPE210 to Deco P9 on 2.4GHz WiFi and then feed the Internet from CPE210 to IPcam by a cable, right?

 

How far is the IPcam away from the CPE210? How far is the CPE210 away from the Deco P9? Any obstacles?

Would the CPE210 in Client mode be able to detect the 2.4GHz WiFi from Deco P9? How about the signal strength?

 

When you use a smartphone (or laptop) standing near the location where you want to install the CPE210, are you able to get a good signal strength from Deco P9 on 2.4GHz WiFi? Please provide as much info as you can for further suggestions. Thank you.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:CPE210 with Deco P9
2020-11-21 17:57:13 - last edited 2020-11-21 18:01:05

@Fae 

 

So you are trying to connect the CPE210 to Deco P9 on 2.4GHz WiFi and then feed the Internet from CPE210 to IPcam by a cable, right? Exactly

 

How far is the IPcam away from the CPE210? There is 2 mètres cable between the IPcam and the CPE21

 

How far is the CPE210 away from the Deco P9? Any obstacles? In the final position, it will be 10 meters with one wall. First of all, I test with only 2 meters without obstacle

 

Would the CPE210 in Client mode be able to detect the 2.4GHz WiFi from Deco P9? Yes, there is 2 BSSID including one withour SSID

 

How about the signal strength? 70 SNR(db)

 

When you use a smartphone (or laptop) standing near the location where you want to install the CPE210, are you able to get a good signal strength from Deco P9 on 2.4GHz WiFi? Yes, i can see the Deco P9 on 2.4GHz WiFi

 

 

I can fill in the fields of Wirless Client Setting but then i click "Next", the CPE210 don't connect to the DecoP9.

But I can connect the CPE210 to another wifi also right next to it

  0  
  0  
#3
Options
Re:CPE210 with Deco P9
2020-11-30 07:39:28

Dear @DK26,

 

Do you have any advanced settings such as access control, MAC filtering configured on the Deco P9?

Have you tested with other CPE210 that you have to check if other CPEs can connect to the Deco P9 on 2.4GHz?

 

I can fill in the fields of Wirless Client Setting but then i click "Next", the CPE210 don't connect to the DecoP9.

 

Please check whether the wireless LED indicators would light up on the CPE210 after you finish the settings.

 

After you configure the CPE210 in Client mode, remember to change the IP settings of the PC back to DHCP(Obtain IP address automatically) and then check the connection.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options
Re:CPE210 with Deco P9
2020-12-06 11:02:29 - last edited 2020-12-06 11:03:03

 

Do you have any advanced settings such as access control, MAC filtering configured on the Deco P9?

No filter

 

Have you tested with other CPE210 that you have to check if other CPEs can connect to the Deco P9 on 2.4GHz?

I have made test with and without 5GHz of the Deco P9

OK, i 'm waiting a second CPE

 

Please check whether the wireless LED indicators would light up on the CPE210 after you finish the settings.

When i connect the CPE210 to the wifi of my internet box (SSIS "Bbox", SNR 58), all is ok.

 

I have 3 Deco P9. When i choose best wifi of the Deco P9 (SSIS "WifiP9", SNR 55) then i click on "Apply", the leds turn off:

 

This is my SSID survey:

  0  
  0  
#5
Options
Re:CPE210 with Deco P9
2020-12-18 06:47:22

Dear @DK26,

 

Would it help if you change the channel width to 20MHz? How about changing WDS from Auto to Disable?

 

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#6
Options
Re:CPE210 with Deco P9
2021-03-08 08:10:30

Hello,

 

I changed the channel width to 20MHz, WDS from Auto to Disable to no avail.
I tested with another CPE 210 but not better.

 

After many many trying, i resolved my problem in one minute with one Ubiquiti Loco M2.
Very strange.

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1061

Replies: 6

About Us
Press
Copyright © TP-Link Corporation Limited. All rights reserved.