Problem with TL-R605 in Omada controller configuration and multiple LAN
Hello,
I have a problem with a TL-R605 in a Omada controller configuration.
I created two lan in Wired Networks>LAN
192.168.0.1 and 192.168.1.1
the second LAN on port 5 (only lan)
but when I connect devices on port 5 they takes ip from the default LAN 192.168.0.1
I don't use any other L3 switches, I only want to use two different network with two unmanaged switches connected to 2 lan port of the R605.
Is this possible?
Some advices?
Thanks
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
The ER605 can only DHCP on one subnet, so you need an Omada compatible switch to do what you want.
- Copy Link
- Report Inappropriate Content
I hope you have looked under Settings / Wired Networks / LAN. Try creating a new LAN, with purpose of "interface" and select the corresponding LAN port, and specify the vlan ID of 1 (since you have no vlans on that interface, but I believe it will still ask you to have a vlan ID, and vlan 1 will mean untagged traffic). Then specify the IP under subnet / gateway (in second subnet) and enable dhcp server and type in the dhcp range etc. This may meet your needs.
Note 4 ports out of 5 are dual personality and marked as WAN / LANx. So those ports can be used for either function. By default LAN network may have all, but first WAN checked in, so you need to first free up port from under LAN wired network and then use this free port to create a new LAN segment on a different subnet than your other LAN segment.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I have a working gateway with latest firmware 1.0.1 and OC300 with 4.2.11 and 12 of EAP245 with 5.0.1, and I have two wireless SSID each with a different subnet (and a management subnet that I have Ip addersses for all network devices, servers and appliances) and wireless clients get IP from the both subnets based on the SSID. One is labeled Private Wi-Fi and other is Guest Wi-Fi. Both interfaces allowed me to set up dhcp scope and I see in the middle of the night, 11 wireless clients, 4 in Guest WiFi subnet of 172.16.xxx.0/24 and 7 in Private subnet of 10.10.xxx.0/24 (I don't have access to the controller but I have access to a server that I can do a IP scan across L3 and see these clients. During the day, I will have 60 plus devices. And this is a business. I am not allowed to send screenshots, else I would have.
And I did not say to uncheck LAN port. There are 3 ports that are labeled WAN/LANx. One is WAN and one is LAN only. Under LAN network, we will have by default LAN port checked in and WAN/LAN1 thru WAN/LAN3 also checked in. We can uncheck one of these dual personality port and should be able to free that one from LAN segment and then use that independently as a second LAN segment.
I do have Qty 4 of 3428XMP switches but I am using them as pure L2 and have no inter-vlan routing or dhcp scopes hosted on the switches.
- Copy Link
- Report Inappropriate Content
You can't uncheck any of the changeable wan/lan ports on the default lan (not talking about lan port, I'm talking about the system generated lan network) and save the change.
Maybe a moderator can answer the question if the ER605 router can DHCP and create multiple subnets, when under Omada control and when not using a switch with DHCP server features.
- Copy Link
- Report Inappropriate Content
Hello,
I can confirm that without a switch you cannot create a separate lan only with the router.
I just bought a TL-SG2008 and now I can separate networks also via interface, not only by vlan.
It was strange for me, because I can't believe that a device like a vpn router cannot do a simple thing like have two separate lan for two different ports, but Tp-Link conceived it like this and we can't do anything else.
Thanks for the support.
- Copy Link
- Report Inappropriate Content
This is annoying as hell. Not just because the lack of a particular feature, but because these limitations do not seem to be mentioned anywhere in their product materials that you'd review before buying. On the specifications page, it even says "DHCP: DHCP Server/Client • DHCP Address Reservation • Multi-net DHCP*** • Multi-IP Interfaces***" with the *** stating that it is a "Controller Mode" feature, and not that it requires an Omada enabled switch.
massimilianop wrote
It was strange for me, because I can't believe that a device like a vpn router cannot do a simple thing like have two separate lan for two different ports, but Tp-Link conceived it like this and we can't do anything else.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 4012
Replies: 7
Voters 0
No one has voted for it yet.