Home

Forums

Stories

Knowledge Base

Business Community > Pharos Wireless Bridges > CPE 210 low mbps in client

< Pharos Wireless Bridges

CPE 210 low mbps in client

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

CPE 210 low mbps in client

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

goryo

2021-06-01 03:06:22 - last edited 2021-06-02 09:45:07

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-06-01

CPE 210 low mbps in client

2021-06-01 03:06:22 - last edited 2021-06-02 09:45:07

Model: CPE210

Hardware Version: V3

Firmware Version: 2.2.0 Build 20190815 Rel. 68786 (0000)

SETUP

1 CPE210 (AP) - connected to PoE adapter -> connected to TL-SF1008D(8 port switch 10/100mbps) -> connected to TP LINK AC1200 (router)

1 CPE210 (CLIENT) - connected to PoE adapter - connected to TL-WR840N (router)

Internet speed provided by ISP: 50Mbps

Distance between two antennas: approx. 500 meters

PROBLEM

The client is only receiving maximum of 3Mbps

Expected connection speed: around 20Mbps

ref.

ap config

client config

3 Reply

Philbert

LV5

2021-06-01 23:23:42 - last edited 2021-06-02 09:45:07

Posts: 2607

Helpful: 1544

Solutions: 273

Stories: 0

Registered: 2020-11-08

Re:CPE 210 low mbps in client

2021-06-01 23:23:42 - last edited 2021-06-02 09:45:07

@goryo

Its been a while since I looked at a CPE, but I would recommend you try the following

Enable MaxStream

Change the bandwidth to 40mhz (anything but 10mhz)

goryo

LV1

2021-06-07 14:28:51 - last edited 2021-06-07 14:29:26

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-06-01

Re:CPE 210 low mbps in client

2021-06-07 14:28:51 - last edited 2021-06-07 14:29:26

@Philbert

I've changed the channel width to 20/40 mhz, and noticed the difference. My client is now reaching around maximum of 30mbps but its not stable. Is there other factors that affect the stability of the connection?

Philbert

LV5

2021-06-07 19:09:17

Posts: 2607

Helpful: 1544

Solutions: 273

Stories: 0

Registered: 2020-11-08

Re:CPE 210 low mbps in client

2021-06-07 19:09:17

@goryo

Hey again

Glad that increased the speed for you!

In relation to stability, you could try the following.

1. Enable MaxStream - seen this help to stabilize speeds in previous setups. Enable and test for a bit, its a TP Link standard but had good success with it.

2. Try changing the channel, as you are running on 2.4ghz you will be using a very congested frequency range. Most people will be broadcasting on 1 6 or 11 personally I would try each one individually see what is best.. OR go to channel 13 if you are allowed in your country, its generally un-used.

Give those at try

CPE 210 low mbps in client

CPE 210 low mbps in client

Information

Voters 0

Tags