Omada Hardware Controller crashed on update 4.4.6

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Omada Hardware Controller crashed on update 4.4.6
Omada Hardware Controller crashed on update 4.4.6
2021-10-25 14:42:54
Model: OC200  
Hardware Version: V1
Firmware Version: 4.4.6

Hi,

 

the omada software crashed on the update to 4.4.6. I had the same problem on update to 4.4.4.

 

The Controller Webinterface doesent work and the controller is not pingable.

  0      
  0      
#1
Options
7 Reply
Re:Omada Hardware Controller crashed on update 4.4.6
2021-10-26 02:01:33

@Christian2705 when did they release 4.4.6 for the OC200?  Or are you stating you tried to load 4.4.6 software on your PC?

  0  
  0  
#2
Options
Re:Omada Hardware Controller crashed on update 4.4.6
2021-10-26 06:15:24

@Fleegle61 my controller showed me that a update is available

  0  
  0  
#3
Options
Re:Omada Hardware Controller crashed on update 4.4.6
2021-10-26 09:22:14

@Christian2705 

 

 

It's a bit wired, I tried the upgrade before with no problems.

Was there any error message shown when you upgrade?

After you upgrade whether the page shows update successfully?

 

BTW, was there any power outages, disconnection or anything like that during upgrade?

  0  
  0  
#4
Options
Re:Omada Hardware Controller crashed on update 4.4.6
2021-10-26 13:35:58

@Christian2705 I saw FAE's post only after you mentioned it.  So TP-LINK was a little slow getting the word out.  I was still on 4.4.4 but went ahead and upgraded to 4.4.6 and had no problems with the upgrade.  

 

I just let it do its thing for about 5-10 minutes and it was fine.  

  0  
  0  
#5
Options
Re:Omada Hardware Controller crashed on update 4.4.6
2021-10-29 03:16:13

@Christian2705 

 

if you're talking about software controller, that's localhost:port# address. Not an IP. Not even ping-able. 

 

Do you mean OC200/OC300? If that's your case, please wait for a longer time. I remember that update will take around 5-10 minutes. You have to wait for the update to finish or will cause a system error. 

  0  
  0  
#6
Options
Re:Omada Hardware Controller crashed on update 4.4.6
2021-10-30 15:18:11 - last edited 2021-10-30 15:19:15

@Christian2705  Have Just upgraded my OC200 to version 4.4.6, Everything appears to have gone smoothly, I started the update from the Controller (Check for updades) under maintenance and just left it for 10 - 15 minutes, when I came back it had returned to the main Login Screen, I logged in and checked to make sure the firmware version had taken, and it shows it's now running version 4.4.6.

 

It's early day's but everything was re-adopted ok, and I checked my wireless networks and vlans, firewall rules etc and everything seems to be in order.

 

I upgraded from version 4.4.4.

 

  

  0  
  0  
#7
Options
Re:Omada Hardware Controller crashed on update 4.4.6
2021-11-09 21:36:47

@Christian2705 

 

Hello did upgrade of two OC200 from version 4.4.4 to 4.4.6

 

One succeeded the update but the other not reachable anymore. The Cloud led not blinking and als not pingable.

 

When I push the reset button wil be the config deleted? From this OC200 i don't have backup?

 

Thanks,

Edwin

  0  
  0  
#8
Options