VPN IP Pool range always from xxx.xxx.xxx.1

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

VPN IP Pool range always from xxx.xxx.xxx.1

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
VPN IP Pool range always from xxx.xxx.xxx.1
VPN IP Pool range always from xxx.xxx.xxx.1
2022-03-25 08:25:03 - last edited 2022-03-29 02:40:55
Model: ER605 (TL-R605)  
Hardware Version: V1
Firmware Version: 1.2.0

Hello,

I am using ER605 with L2TP/IPSec VPN server under the Omada SDN Linux Controller V5.1.7 and I have discovered, that IP Pool for VPN clients is always starts from xxx.xxx.xxx.1. Is it any chance how to change it?

 

I have set IP Pool xxx.xxx.xxx.220/24 in the VPN settings but it is always getting IPs to the clients from the start of subnet xxx.xxx.xxx.1 and this mess my IP address segmentation.

 

How can I set up the IP Range from the IP address xxx.xxx.xxx.220?

  0      
  0      
#1
Options
1 Accepted Solution
Re:VPN IP Pool range always from xxx.xxx.xxx.1-Solution
2022-03-25 15:14:34 - last edited 2022-03-29 02:40:55

Libik wrote

Hello,

I am using ER605 with L2TP/IPSec VPN server under the Omada SDN Linux Controller V5.1.7 and I have discovered, that IP Pool for VPN clients is always starts from xxx.xxx.xxx.1. Is it any chance how to change it?

 

I have set IP Pool xxx.xxx.xxx.220/24 in the VPN settings but it is always getting IPs to the clients from the start of subnet xxx.xxx.xxx.1 and this mess my IP address segmentation.

 

How can I set up the IP Range from the IP address xxx.xxx.xxx.220?

  @Libik  Not sure about xxx.xxx.xxx.220.   Try setting for xxx.xxx.xxx.224/27  -- this should give you up to 30 usable addresses, within the range xxx.xxx.xxx.225 to xxx.xxx.xxx.254.

 

Broadcast address is xxx.xxx.xxx.255

Recommended Solution
  1  
  1  
#2
Options
2 Reply
Re:VPN IP Pool range always from xxx.xxx.xxx.1-Solution
2022-03-25 15:14:34 - last edited 2022-03-29 02:40:55

Libik wrote

Hello,

I am using ER605 with L2TP/IPSec VPN server under the Omada SDN Linux Controller V5.1.7 and I have discovered, that IP Pool for VPN clients is always starts from xxx.xxx.xxx.1. Is it any chance how to change it?

 

I have set IP Pool xxx.xxx.xxx.220/24 in the VPN settings but it is always getting IPs to the clients from the start of subnet xxx.xxx.xxx.1 and this mess my IP address segmentation.

 

How can I set up the IP Range from the IP address xxx.xxx.xxx.220?

  @Libik  Not sure about xxx.xxx.xxx.220.   Try setting for xxx.xxx.xxx.224/27  -- this should give you up to 30 usable addresses, within the range xxx.xxx.xxx.225 to xxx.xxx.xxx.254.

 

Broadcast address is xxx.xxx.xxx.255

Recommended Solution
  1  
  1  
#2
Options
Re:VPN IP Pool range always from xxx.xxx.xxx.1
2022-03-25 16:27:17

  @GaelForce 

That does not come to my mind and it is working. Thank you for your help.

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 604

Replies: 2