Business Community > WiFi > EAP 610 an EAP 620 HD POE Injector
< WiFi

EAP 610 an EAP 620 HD POE Injector

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP 610 an EAP 620 HD POE Injector

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP 610 an EAP 620 HD POE Injector
EAP 610 an EAP 620 HD POE Injector
2022-04-10 19:52:38 - last edited 2022-04-11 11:07:18
Model: EAP620 HD  
Hardware Version: V2
Firmware Version: 1.0.3

Hi everyone

 

I am setting up new home network and i have Eap225, Eap610 and Eap620. For eap 610 and 620, i am going to install them remote areas and no power line near them. Also they are far away from my POE+ switch (TL-SG1016PE). I can set up CAT6 cables to the EAPs but power will be an issue. the question is both eap610 and eap620 power consuption around 13w, but they are supporting 802.3at. Can I use TL-POE150S injectors (supporting 802.3af) with Eap610 and Eap620? Or do i need TL-POE160S (802.3at)?

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:EAP 610 an EAP 620 HD POE Injector-Solution
2022-04-11 11:07:04 - last edited 2022-04-11 11:07:18

 Dear @TurboOrdek 

 

No, TL-POE150S injectors are not good for EAP620 HD/660 HD. Although they are not more than 14W they still cannot simple work with 802.3af PoE.

 

TL-POE160S is required.

 

For EAP620 HD v3, there is a passive PoE injector in the box, so you don't need to buy additional one. 

But EAP660HD doesn't support passive PoE and no poe injector in the box.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  2  
  2  
#2
Options
3 Reply
Re:EAP 610 an EAP 620 HD POE Injector-Solution
2022-04-11 11:07:04 - last edited 2022-04-11 11:07:18

 Dear @TurboOrdek 

 

No, TL-POE150S injectors are not good for EAP620 HD/660 HD. Although they are not more than 14W they still cannot simple work with 802.3af PoE.

 

TL-POE160S is required.

 

For EAP620 HD v3, there is a passive PoE injector in the box, so you don't need to buy additional one. 

But EAP660HD doesn't support passive PoE and no poe injector in the box.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  2  
  2  
#2
Options
Re:EAP 610 an EAP 620 HD POE Injector
2022-04-11 14:19:58 - last edited 2022-10-13 11:38:30

EDIT

  0  
  0  
#3
Options
Re:EAP 610 an EAP 620 HD POE Injector
2022-04-13 20:10:13

@TurboOrdek,

 

How long is the run?  PoE is typically good for ~50-60 meters with high quality cable.  That is to say roughly half the distance of the 100 meter Ethernet standard.  Though YMMV depending on which PoE power standard (and thus voltage) is used, the load on the switch, and termination resistance.

 

Better to pull an extension cord along with your Ethernet cable.  Or, better yet, use a directional, outdoor Wifi AP solution aimed in the direction of desired coverage

 

There are various companies that make PoE extenders, too.  Some even claim over 100 meters -- which I don't understand since what's the point of PoE if the data side of things isn't working.  

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 3168

Replies: 3

Related Articles
 EAP-620 HD - Firmware?
2038 0
 EAP 620 no mesh
1075 0
 EAP 620 HD keeps changing ip address of mobile device
412 0
 10% Dropped Packets on EAP 620's
1537 0
Poe for EAP620 HD
603 0
 EAP 115 POE injector
778 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.