Omada Software Controller....not workin corretly

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Omada Software Controller....not workin corretly

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Omada Software Controller....not workin corretly
Omada Software Controller....not workin corretly
2022-05-01 18:53:34

hi all .... I have a strange problem with omada via software and not sdn. I have router with ip 192.168.1.1 and if I connect my static pc 192.168.1.240 with open ports directly to the router omada software controller 3.4.2 also works perfectly from a mobile phone with connected access points I have installed mikrotik 4011 and since then omada no longer works, ie I regularly access omada remotely but I see unconnected access points. now the configuration is: main router: 192.168.0.1 with dmz to mikrotik 192.168.0.200 Mikrotik 192.168.1.1 and the same ports of the tim router have been opened on the mikrotik and the pc always has the same ip. so i see controller up but access points not connected. could you help me?

 

access point are: Eap 110 and eap 225

  0      
  0      
#1
Options
10 Reply
Re:Omada Software Controller....not workin corretly
2022-05-06 18:12:25

  @Andrew71 

 

news for me???? help me. please

  0  
  0  
#2
Options
Re:Omada Software Controller....not workin corretly
2022-05-09 05:36:27

  @Andrew71 

Omada Controller software requires two things to work:

1. It must be able to communicate with the AP. You may try ping the EAP IP from controller PC;

2. Software uses port 29810-29814, make sure these ports are available and useable on this PC.

  0  
  0  
#3
Options
Re:Omada Software Controller....not workin corretly
2022-07-30 18:06:50

  @Andrew71 

 

hi mister, thanks for your help but i have still problems attached I put the screen of my omada software controller as follows: router with ip gateway 192.168.1.1 pc where omada is installed: 192.168.1.243 open doors: 29810,29811,29812,29813, 8043, and 8088. the controller points to 192.168.1.243:8043 everything works correctly even from the mobile app. now i changed pc and i installed omada again, with the following parameters: router with ip gateway 192.168.1.1 pc where omada is installed: 192.168.1.238 open doors: 29810,29811,29812,29813, 8343, and 8188. the controller points to 192.168.1.238:8343 my problem is: i did backup and restore, and also migrate site, but eap and sites have been imported, but i see disconnected devices. how can i solve my problem? I look forward to the solution. thanks always. please

File:
Controller.jpgDownload
  0  
  0  
#4
Options
Re:Omada Software Controller....not workin corretly
2022-08-06 17:47:17

  @Andrew71 

 

hi all the forum? ther is news for me???? hlep me please

  0  
  0  
#5
Options
Re:Omada Software Controller....not workin corretly
2022-08-06 19:35:39

  @Andrew71 I think people can't understand you.

 

Is your PC able to ping EAPs? Please attach ouput from ping to each EAP.

  0  
  0  
#6
Options
Re:Omada Software Controller....not workin corretly
2022-08-07 09:46:29

Andrew71 wrote

  @Andrew71 

 

hi all the forum? ther is news for me???? hlep me please

  @Andrew71 

Hi,

can you try these steps:

 

1) update omada software to the latest version

2) update the EAPs to the lastest firmware version

 

Then:

3) from the omada pc ping the EAPs

4) check if the necessary ports are reachable

 

Let us know how it worked out.

Marcus

 

  0  
  0  
#7
Options
Re:Omada Software Controller....not workin corretly
2022-08-07 13:34:47

  @Andrew71 

 

hi, i have tried but not resolve.

i my problem is export backup from old controller and import restore into new controller. the pc is different

  0  
  0  
#8
Options
Re:Omada Software Controller....not workin corretly
2022-08-07 17:26:07

  @Andrew71 

 

I don't see output from ping commands to each EAP from new Omada controller PC.

  0  
  0  
#9
Options
Re:Omada Software Controller....not workin corretly
2022-08-14 18:07:31 - last edited 2022-08-14 18:56:01

  @Andrew71 

hi mister...

thanks for your availability

i have changed all

i reset all device and i insert a new controller software.

but i have also problem

i have reset eap 235 wall

into schedule System-Controller settings i have insert the url of my controller but not adopt. i have used also omada discovery and the result is succeded, but howewer not adopt.

my settings is:

my public ip:8343 my url controller and i connect of remote.

my public ip:29810 insert into eap and into omada discovery with username and password

the port 29810 is open on tcp/udp into ip address my pc of is controller open (port forwarding on router)

 

i have also access from smartphone to controller, but the problem is not adopting the device.

how i ping commands to each EAP from new Omada controller PC?

 

why is not adopt?

 

  0  
  0  
#10
Options
Re:Omada Software Controller....not workin corretly
2022-08-16 18:05:31

  @Andrew71 

 

hi all the forum

i have a question...

i have installed Oc200 Omada Sdn Controller

if i used IP:port for access to controller, the software omada i can delete?

the controller i ping also remote access

one problem:

which port i open for adopt device to remote?

  0  
  0  
#11
Options

Information

Helpful: 0

Views: 568

Replies: 10