EAP660 slow wifi
EAP660 slow wifi
Hoping someone can help me out. I have the EAP660 HD version and have not been that impressed by it. Most likely something with my configuration I'm guessing (using mostly default settings) but if anyone can provide any tips, I'd appreciate it.
My current setup:
Bell Fibe 940mbps down / 750mbps up
TP-Link Gigabit SFP to RJ45 Fiber Media Converter (MC220L)
Mikrotik HAP AC2 router
TP-Link EAP660 HD access point (5ghz separate band, 80mhz channel width, auto channel selection)
On my OnePlus 7T device, I'm getting speeds of 250mbps-350mbps download on speedtest.
Using the HH3000, same configuration and distance away, I'm getting 650mbps-700-mbps
Any ideas?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@esaad86 I am not an expert at all but just wondering if you ensured that you are connecting to 5gHz. I am sure you have but just wondering. I have a much smaller Eap615-Wall and can consistently get 500Mbps with an iPhone next to it. Alternatively of course is to switch all the different modes in settings.
- Copy Link
- Report Inappropriate Content
@Hendrics yes, I have the bands separated and I'm connected to the 5ghz band
- Copy Link
- Report Inappropriate Content
esaad86 wrote
Using the HH3000, same configuration and distance away, I'm getting 650mbps-700-mbps
That is all I am ever able to get out of my 660 HD with most devices downstream (AP -> Device), mostly Androids, but even a Windows Laptops with Intel AX Adaptors.
The ONLY device I have that will break that limit is my Work iPhone, its able to hit about 600mbps somewhat regularly.
This is with different FW version, 80mhz, rural area with no interference and different channels.
While these 660HDs have good signal and can allow devices to work at great distances, the speed is just not there.
I have seen others mention this is due to the AP not transmitting using MIMO even when devices support 2x2.
On the other hand, the devices with the 300mbps +/- downstream limit can upload at about double that in the 600mbps, which seems to lend credabilit yto those reports.
- Copy Link
- Report Inappropriate Content
@Napsterbater yeah, my best case scenario right now in direct line of sight of the eap I get 400mbps download and 600mbps upload. Frustrating as I'm replacing the wifi on my hap ac2 which was averaging almost the same and it's only ac1200. Pretty disappointed with it tbh. Tried an Asus xt4 3 node mesh with wired backhaul and I'm getting over 700mbps download (ax1800). Thought it was something in my configuration because specs of the eap660 are much better than all these other devices I've tried
- Copy Link
- Report Inappropriate Content
@esaad86 Maybe try to change the Channel to 36 or 48 to see if there is any difference?
- Copy Link
- Report Inappropriate Content
Using my house as an example
Omada Controller v5.4.6
3x EAP660HD on firmware v1.1.1 Build 20220118 Rel. 60852
-all APs connected at 2.5gb
I have 3 5ghz SSIDs being broadcast
-802.11r is enabled
-all have minimum data rate control enabled and set to 54Mbps
-Require clients to use rates at or above the specified value
I have 1 2.4ghz SSID being broadcast
-no special options enabled
Fast Roaming is enabled
AI Roaming is enabled
DTIM Period for 2.4 and 5ghz is set to 2 from the default of 1.
Airtime Fairness for 2.4 and 5ghz is enabled
2.4ghz is set to 20mhz
5ghz is set to 80mhz
Channels manually set for each AP as best as can be for 2.4 and 5ghz to limit overlapping.
I am in a typical suburban area in the midwest. So I do see other wireless networks around me.
I get iperf3 numbers from intel ax adapters and ax phones (like one plus 8t and pixel 6) consistently over 800mbps with bursts over 1gbps to my local file/media server connected via 10gb. This is also with 75+ wireless devices connected. Doing internet speed tests to openspeedtest or fast.com gives me the same results (at least for download as I'm not lucky enough to have fiber in my area, stuck with over provisioned cable). All of that with sub 80ms latency as well.
This, just to say, the EAP660HD is def capable of faster speeds than you are seeing. If you are expecting consistently faster than 800mbps over wifi, you will need an AP that is 160mhz and clients that are the same kind of 160mhz (80+80 vs 160mhz). You also need to realize that business APs, like the EAP660HD are built more towards density vs single client speed. In any case, I am able to cap 80mhz channel bandwidth with 75+ devices connected across 3 APs.
- Copy Link
- Report Inappropriate Content
@Somnus tried but it results in lower speeds
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I'm just using the software controller. It's a free download, so I'd say it's worth a try. You could also run the new AI Optimizer in v5.4.6 to see if that helps out at all.
In terms of DFS channels, I doubt the current hardware revision EAP660HDs will get DFS channels with firmware updates... at least not in the US. As it would require TP-Link to recertify them with the FCC.... unless I just missed the DFS channels in their current certifications. If they were in current certifications I'm not sure why they wouldn't have been released with them. In anycase, would be great to see usable DFS channels though.
- Copy Link
- Report Inappropriate Content
@Vilmalith The controller is going to have zero effect on speed.
This has already been shoen to be an issue with the 660HDs spicificly, and potinally other APs.
Many have resported this issue via these forms and reddit, and one person was able to show its becuase the AP is not properly transmitting to many clients with MIMO so you only get half the expected realistic speed on those deivces.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 3453
Replies: 16