Forums

Stories

Knowledge Base

Business Community > Controllers > Displaying the wrong client IP Address

< Controllers

Displaying the wrong client IP Address

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Displaying the wrong client IP Address

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Tim_Tang

LV1

2023-02-13 05:23:27 - last edited 2023-02-15 05:46:45

Posts: 3

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2021-09-19

Displaying the wrong client IP Address

2023-02-13 05:23:27 - last edited 2023-02-15 05:46:45

Model: OC200

Hardware Version: V1

Firmware Version: 1.21.7 Build 20221206 Rel.58608

I have a NAS previously assigned to a fixed IP address of 10.10.10.100. I changed the NAS IP address to 10.10.10.20. I did this by changing the NAS' static IP address to 10.10.10.20 and enabled fixed address for the client on Omada Controller. Now, the NAS is on 10.10.10.20, and I can access the NAS at that address.

Everything seems to work as it should. HOWEVER, the Omada Controller is still displaying 10.10.10.100 IP address for the client. There is no device at that address. I even tried rebooting the controller. Why the controller is still displaying the old address?

Tim

1 Accepted Solution

Tim_Tang

LV1

2023-02-14 16:09:35 - last edited 2023-02-15 05:46:45

Posts: 3

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2021-09-19

Re:Displaying the wrong client IP Address-Solution

2023-02-14 16:09:35 - last edited 2023-02-15 05:46:45

@Hank21

Ok. Rebooting the Gateway(DHCP server) fixed the problem.

Thanks!

Tim

Recommended Solution

2 Reply

Hank21

2023-02-14 09:03:44

Posts: 3026

Helpful: 659

Solutions: 399

Stories: 8

Registered: 2021-12-13

Re:Displaying the wrong client IP Address

2023-02-14 09:03:44

Dear @Tim_Tang ，

Tim_Tang wrote

Everything seems to work as it should. HOWEVER, the Omada Controller is still displaying 10.10.10.100 IP address for the client. There is no device at that address. I even tried rebooting the controller. Why the controller is still displaying the old address?

Thank you so much for taking the time to report the issue to our community!

1. Could you please reboot the router(DHCP Server) and test again?

2. May I take a look at the Client list which may show this issue?

3. Have you compared the MAC address between IP 10.10.10.100 and your NAS to check if it is still the NAS?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

Tim_Tang

LV1

2023-02-14 16:09:35 - last edited 2023-02-15 05:46:45

Posts: 3

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2021-09-19

Re:Displaying the wrong client IP Address-Solution

2023-02-14 16:09:35 - last edited 2023-02-15 05:46:45

@Hank21

Ok. Rebooting the Gateway(DHCP server) fixed the problem.

Thanks!

Tim

Information

Helpful: 0

Replies: 2

Displaying the wrong client IP Address

Displaying the wrong client IP Address

Information

Voters 0

Tags