Is this the proper way for remote management in ER7206 V1 standalone

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Is this the proper way for remote management in ER7206 V1 standalone

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Is this the proper way for remote management in ER7206 V1 standalone
Is this the proper way for remote management in ER7206 V1 standalone
2023-03-14 03:50:05 - last edited 2023-03-15 05:17:05
Model: ER7206 (TL-ER7206)  
Hardware Version: V1
Firmware Version: 1.2.3 Build 20221104 Rel.41500

ER7206 V1 on `192.168.20.0/24` with IP address `192.168.20.1`

 

Remote management by a PC at the same subnet with IP address of `192.168.20.240/32`

 

Is this correct? If not, I will probably be locked out.

 

Screenshot Screenshot

 

I found extra resource on this topic Configure remote management on SMB router . Not sure how helpful. I don't think this Remote Management is here to secure the page from Local traffic.

 

  0      
  0      
#1
Options
1 Accepted Solution
Re:Is this the proper way for remote management in ER7206 V1 standalone-Solution
2023-03-15 05:11:47 - last edited 2023-03-15 05:17:05

 Hi @YuukiA 

 

Remote Management is used to manage your router from WAN side. It's not used to secure the page from local LAN network. 

 

The subnet/mask should be a WAN side IP(in normal case a public IP), so you can login the router via it's WAN IP address.

 

If you want to login the router from anywhere, you can put in 0.0.0.0/0 as the remote IP, so all IP that can communicate with your router WAN, will be able to open the router login page. 

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
2 Reply
Re:Is this the proper way for remote management in ER7206 V1 standalone-Solution
2023-03-15 05:11:47 - last edited 2023-03-15 05:17:05

 Hi @YuukiA 

 

Remote Management is used to manage your router from WAN side. It's not used to secure the page from local LAN network. 

 

The subnet/mask should be a WAN side IP(in normal case a public IP), so you can login the router via it's WAN IP address.

 

If you want to login the router from anywhere, you can put in 0.0.0.0/0 as the remote IP, so all IP that can communicate with your router WAN, will be able to open the router login page. 

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#2
Options
Re:Is this the proper way for remote management in ER7206 V1 standalone
2023-03-15 05:16:57

  @Hank21 

 

> If you want to login the router from anywhere, you can put in 0.0.0.0/0 as the remote IP, so all IP that can communicate with your router WAN, will be able to open the router login page. 

 

Finally! I understand now. I have set the value to `0.0.0.0/0` and now I can login to the login page from the outside. Thank you so much for your help.

  0  
  0  
#3
Options