Only 300 MNbit instead of 1Gbit ER707 using LAN Port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Only 300 MNbit instead of 1Gbit ER707 using LAN Port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Only 300 MNbit instead of 1Gbit ER707 using LAN Port
Only 300 MNbit instead of 1Gbit ER707 using LAN Port
2023-07-27 17:23:24

Hi,

i have an ER707-M2 and use only the first WAN port for WAN.   The other ports are configured as LAN Ports.    But i only get anout 300 Mbit insetad of 1000 Mbit when doing speed test ...   HArdware Offload is on ... Using it with an OC300 and controller 5.9.

 

Any idea ?  No Qos and so on turned on 

  0      
  0      
#1
Options
6 Reply
Re:Only 300 MNbit instead of 1Gbit ER707 using LAN Port
2023-07-27 17:50:41

It is really getting bad with TP Link.    When using the ER707 in Standalone Mode i can tur on Flow Control .... And then i get full speed ....   But Flow Control isnt in Omada already  ...   I think i will switch to another manufacturer... That is too silly what tp link does.  

  0  
  0  
#2
Options
Re:Only 300 MNbit instead of 1Gbit ER707 using LAN Port
2023-07-27 18:56:49 - last edited 2023-07-27 19:20:26

  @Daniel2908 

I have only 500/500 but have full speed. Use 2.5gb wan port. Dynamic ip so its strange that you only have 300 Mbps. 

Controller 5.12. 

Firware is 1.1.0

 

EIDIT:

Flow controll is not supported for ER707-M2 in controller 5.12 only ER605v2.

so we have to wait for a firmware update for ER707-M2

 

ER605v2

 

ER707-M2

 

 

 

  0  
  0  
#3
Options
Re:Only 300 MNbit instead of 1Gbit ER707 using LAN Port
2023-07-28 04:32:13

Thank you for your information. That shows me again how ... TP LINK Omada is... Thank you. Inreally hoped it would be better with 5.11 and 5.12 but now i know it won't

  0  
  0  
#4
Options
Re:Only 300 MNbit instead of 1Gbit ER707 using LAN Port
2023-07-28 06:10:20

Hello @Daniel2908

 

Thanks for reporting this issue to TP-Link community!

 

May I know which port you have tried to enable the Flow Control?

Could you tell us who is your Internet Service Provider?

Could you share a screenshot of the speed test result? Did you use the Iperf to test the speed?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options
Re:Only 300 MNbit instead of 1Gbit ER707 using LAN Port
2023-07-28 06:39:41

I can enable flow control on the ER707 only in standalone mode .  With Omada COntroller 5.9.2 (OC300) there is no option to enable flow control in the omada controller or device settings. 

  0  
  0  
#6
Options
Re:Only 300 MNbit instead of 1Gbit ER707 using LAN Port
2023-07-28 07:29:32

I packed the ER707 and the OC300 too and will send everything back. No desire to annoy me further about the missing functions and the constant callbacks of firmware updates. 

  0  
  0  
#7
Options