Migration

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Migration

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Migration
Migration
2023-08-02 16:20:21 - last edited 2023-08-09 02:28:34
Hardware Version:
Firmware Version: 5.9.31

I am currently using the software controller v5.9.31. I am lookin to impliment a hardware controller oc300 instead. Looking at it, the versions do not line up (v5.9.32) on the oc300. Are these compatable to preform a migration, Software v5.9.31 -> Hardware v5.9.32?

 

Many thanks for any advice.

  0      
  0      
#1
Options
2 Accepted Solutions
Re:Migration-Solution
2023-08-03 06:07:36 - last edited 2023-08-09 02:28:34

Hello @Bretagne,

 

Yes, you can perform the Migration from Software Controller 5.9.31 to OC300 5.9.32. You may refer to this document.

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
Re:Migration-Solution
2023-08-09 02:28:27 - last edited 2023-11-27 12:15:19

Hi @Bretagne,

 

Yes, from Software Controller 5.9.31 to OC300 5.9.32 is OK. You may give it a try.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#4
Options
5 Reply
Re:Migration-Solution
2023-08-03 06:07:36 - last edited 2023-08-09 02:28:34

Hello @Bretagne,

 

Yes, you can perform the Migration from Software Controller 5.9.31 to OC300 5.9.32. You may refer to this document.

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
Re:Migration
2023-08-03 07:02:39

  @Hank21 Thank you. I was hoping that that was the answer. I was only concerned the the version was not an identical match and might cause issues.

So I take it the version is just the v5.xx.xx ?

  0  
  0  
#3
Options
Re:Migration-Solution
2023-08-09 02:28:27 - last edited 2023-11-27 12:15:19

Hi @Bretagne,

 

Yes, from Software Controller 5.9.31 to OC300 5.9.32 is OK. You may give it a try.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#4
Options
Re:Migration
2023-11-27 12:15:49

  @Hank21 Forgot to update the thread. Migration went smoothly with no issues.

  0  
  0  
#5
Options
Re:Migration
2023-11-28 01:01:21

Hi @Bretagne

 

Thank you for your valued feedback! Glad to hear that your concern was resolved finally.

Hope you enjoy the Internet with TP-Link products and have a great day!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#6
Options